Messages in this thread | | | Date | Wed, 13 Oct 2010 22:26:02 +0100 (BST) | From | fabio tirapelle <> | Subject | Hauppauge WinTV-HVR-1120 on Unbuntu 10.04 |
| |
Yesterday I have installed (added not substituted) a new tuner: Hauppauge Nova-T Stick 3 Today the WinTV-HVR-1120 doesn't works. I attach my /var/log/messages
lsusb
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 15c2:0036 SoundGraph Inc. Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 2040:7070 Hauppauge Nova-T Stick 3 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
lscpi
00:00.0 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP78S [GeForce 8200] LPC Bridge (rev a2) 00:01.1 SMBus: nVidia Corporation MCP78S [GeForce 8200] SMBus (rev a1) 00:01.2 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller (rev a1) 00:01.3 Co-processor: nVidia Corporation MCP78S [GeForce 8200] Co-Processor (rev a2) 00:01.4 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller (rev a1) 00:02.0 USB Controller: nVidia Corporation MCP78S [GeForce 8200] OHCI USB 1.1 Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP78S [GeForce 8200] EHCI USB 2.0 Controller (rev a1) 00:04.0 USB Controller: nVidia Corporation MCP78S [GeForce 8200] OHCI USB 1.1 Controller (rev a1) 00:04.1 USB Controller: nVidia Corporation MCP78S [GeForce 8200] EHCI USB 2.0 Controller (rev a1) 00:06.0 IDE interface: nVidia Corporation MCP78S [GeForce 8200] IDE (rev a1) 00:07.0 Audio device: nVidia Corporation MCP72XE/MCP72P/MCP78U/MCP78S High Definition Audio (rev a1) 00:08.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Bridge (rev a1) 00:09.0 IDE interface: nVidia Corporation MCP78S [GeForce 8200] SATA Controller (non-AHCI mode) (rev a2) 00:0a.0 Ethernet controller: nVidia Corporation MCP77 Ethernet (rev a2) 00:0b.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express Bridge (rev a1) 00:10.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express Bridge (rev a1) 00:12.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express Bridge (rev a1) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:06.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d1) 01:07.0 Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card (rev 02) 02:00.0 VGA compatible controller: nVidia Corporation C77 [GeForce 8200] (rev a2)
> ----- Messaggio originale ----- > > Da: Bjorn Helgaas <bjorn.helgaas@hp.com> > > A: fabio tirapelle <ftirapelle@yahoo.it> > > Cc: linux-kernel@vger.kernel.org; Michael Krufky <mkrufky@kernellabs.com> > > Inviato: Mer 13 ottobre 2010, 21:54:31 > > Oggetto: Re: Hauppauge WinTV-HVR-1120 on Unbuntu 10.04 > > > > On Wednesday, October 13, 2010 01:02:11 pm fabio tirapelle wrote: > > > After upgrading from Ubuntu 9.10 to Ubuntu 10.04 my Hauppauge >WinTV-HVR-1120 > > > > > > (sometimes) doesn't work correctly. > > > I get random the following errors: > > > > > > tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer returned: -5 > > > tda18271_init: error -5 on line 826 > > > tda18271_tune: error -5 on line 904 > > > tda18271_set_params: error -5 on line 985 > > > > I cc'd Michael since he made several recent tda18271 changes. > > > > This page: http://cvs.linuxtv.org/wiki/index.php/Zolid_Hybrid_TV_Tuner > > suggests that the card might work, despite the error messages. Does > > yours work? > > > > I see that tda18271_write_regs() uses i2c_transfer(), which uses the > > adap->algo->master_xfer function pointer, but I don't know enough to > > figure out which master_xfer implementation might be used on your > > system. A complete dmesg log and lspci output might have a hint. > > > > Can you reproduce this on an upstream kernel? It would be good to > > make sure that it's not something introduced by an Ubuntu patch or > > fixed since the Ubuntu kernel snapshot. > > > > Bjorn > > > > > Part of dmesg of 11-OCT-2010 > > > > > > [ 53.216153] DVB: registering new adapter (saa7133[0]) > > > [ 53.216156] DVB: registering adapter 2 frontend 0 (NXP TDA10048HN > >DVB-T)... > > > [ 53.840013] tda10048_firmware_upload: waiting for firmware upload > > > (dvb-fe-tda10048-1.0.fw)... > > > [ 53.840019] saa7134 0000:01:06.0: firmware: requesting > >dvb-fe-tda10048-1.0.fw > > > [ 53.880505] tda10048_firmware_upload: firmware read 24878 bytes. > > > [ 53.880509] tda10048_firmware_upload: firmware uploading > > > [ 58.280136] tda10048_firmware_upload: firmware uploaded > > > [ 59.024537] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 59.024541] tda18271c2_rf_tracking_filters_correction: error -5 on >line > > >264 > > > [ 59.420153] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 59.420157] tda18271_toggle_output: error -5 on line 47 > > > [ 91.004019] Clocksource tsc unstable (delta = -295012684 ns) > > > [ 256.293639] eth0: link up. > > > [ 256.294750] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > > > [ 263.523498] eth0: link down. > > > [ 265.258740] eth0: link up. > > > [ 266.460026] eth0: no IPv6 routers present > > > [ 9869.636167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 9869.636178] tda18271_init: error -5 on line 826 > > > [ 9872.636220] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 9872.636232] tda18271_toggle_output: error -5 on line 47 > > > [ 9998.240167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 9998.240178] tda18271_init: error -5 on line 826 > > > [10001.240179] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [10001.240190] tda18271_toggle_output: error -5 on line 47 > > > > > > And this is the dmesg of today: even the same errors. > > > > > > [ 741.252183] tda18271_init: error -5 on line 826 > > > [ 741.252188] tda18271_tune: error -5 on line 904 > > > [ 741.252193] tda18271_set_params: error -5 on line 985 > > > [ 742.268174] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 742.268184] tda18271_init: error -5 on line 826 > > > [ 742.268189] tda18271_tune: error -5 on line 904 > > > [ 742.268194] tda18271_set_params: error -5 on line 985 > > > [ 743.284174] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 743.284184] tda18271_init: error -5 on line 826 > > > [ 743.284190] tda18271_tune: error -5 on line 904 > > > [ 743.284194] tda18271_set_params: error -5 on line 985 > > > [ 744.300169] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 744.300180] tda18271_init: error -5 on line 826 > > > [ 744.300185] tda18271_tune: error -5 on line 904 > > > [ 744.300190] tda18271_set_params: error -5 on line 985 > > > [ 745.320172] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 745.320183] tda18271_init: error -5 on line 826 > > > [ 745.320188] tda18271_tune: error -5 on line 904 > > > [ 745.320193] tda18271_set_params: error -5 on line 985 > > > [ 746.336174] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 746.336185] tda18271_init: error -5 on line 826 > > > [ 746.336190] tda18271_tune: error -5 on line 904 > > > [ 746.336195] tda18271_set_params: error -5 on line 985 > > > [ 747.352170] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 747.352181] tda18271_init: error -5 on line 826 > > > [ 747.352187] tda18271_tune: error -5 on line 904 > > > [ 747.352192] tda18271_set_params: error -5 on line 985 > > > [ 748.368172] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 748.368183] tda18271_init: error -5 on line 826 > > > [ 748.368188] tda18271_tune: error -5 on line 904 > > > [ 748.368193] tda18271_set_params: error -5 on line 985 > > > [ 749.384179] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 749.384191] tda18271_init: error -5 on line 826 > > > [ 749.384196] tda18271_tune: error -5 on line 904 > > > [ 749.384202] tda18271_set_params: error -5 on line 985 > > > [ 750.400172] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 750.400182] tda18271_init: error -5 on line 826 > > > [ 750.400188] tda18271_tune: error -5 on line 904 > > > [ 750.400194] tda18271_set_params: error -5 on line 985 > > > [ 751.424170] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > [ 751.424181] tda18271_init: error -5 on line 826 > > > [ 751.424186] tda18271_tune: error -5 on line 904 > > > [ 751.424192] tda18271_set_params: error -5 on line 985 > > > [ 752.440172] tda18271_write_regs: ERROR: idx = 0x5, len = 1, >i2c_transfer > > > > > returned: -5 > > > > > > > > > > > > > > > > > > Any ideas? > > > Thanks > > > > > > > > > > > > > > > > >
[unhandled content-type:application/zip]
| |