lkml.org 
[lkml]   [2009]   [Jun]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 08/11] Blackfin Serial Driver: handle irregular DMA register status in auto start mode
Date
From: Sonic Zhang <sonic.zhang@analog.com>

This bug is caused by irregular behavior of DMA register CURR_X_COUNT
and CURR_Y_COUNT when an auto restart uart rx DMA run to last byte in
DMA buffer, trigger the interrupt and stay at this possiton. The status
of current x and y is 0:7 instead of 512:8 or 0:8. The driver doesn't
take care of this case when calculating the position.

URL: http://blackfin.uclinux.org/gf/tracker/5063
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reported-by: Tomasz Motylewski <t.motylewski@bfad.de>
---
drivers/serial/bfin_5xx.c | 7 ++++---
1 files changed, 4 insertions(+), 3 deletions(-)

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index 676efda..854e96d 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -490,7 +490,7 @@ void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
- if (uart->rx_dma_nrows == DMA_RX_YCOUNT)
+ if (uart->rx_dma_nrows == DMA_RX_YCOUNT || x_pos == 0)
uart->rx_dma_nrows = 0;
x_pos = DMA_RX_XCOUNT - x_pos;
if (x_pos == DMA_RX_XCOUNT)
@@ -546,15 +546,16 @@ static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id)
{
struct bfin_serial_port *uart = dev_id;
unsigned short irqstat;
- int pos;
+ int x_pos, pos;

spin_lock(&uart->port.lock);
irqstat = get_dma_curr_irqstat(uart->rx_dma_channel);
clear_dma_irqstat(uart->rx_dma_channel);

uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
+ x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
- if (uart->rx_dma_nrows == DMA_RX_YCOUNT)
+ if (uart->rx_dma_nrows == DMA_RX_YCOUNT || x_pos == 0)
uart->rx_dma_nrows = 0;

pos = uart->rx_dma_nrows * DMA_RX_XCOUNT;
--
1.6.3.1


\
 
 \ /
  Last update: 2009-06-02 09:17    [W:0.089 / U:0.568 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site