lkml.org 
[lkml]   [2009]   [Mar]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Subject[Bug #11550] pnp: Huge number of "io resource overlap" messages
    Date
    On Friday 26 September 2008, Bjorn Helgaas wrote:
    > http://bugzilla.kernel.org/show_bug.cgi?id=11550

    Sorry for having to revive this old thread. In November 2008 I reported
    that this issue had been solved for me as a result of 1f98757776ea, but I
    now find that was due to faulty testing. (I suspect that changing the BIOS
    setting that affects this issue on my Toshiba laptop only takes effect
    after a cold boot, not a normal reboot.)

    The problem was that with the BIOS setting for "Device config" set to
    "Setup by OS", I get 78 messages like:
    pnp 00:08: io resource (0x2e-0x2f) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x2e-0x2f) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling

    If the BIOS setting is set to "All Devices", the problem does not occur.

    The origin of these messages was bisected to:
    commit aee3ad815dd291a7193ab01da0f1a30c84d00061
    Author: Bjorn Helgaas <bjorn.helgaas@hp.com>
    Date: Fri Jun 27 16:56:57 2008 -0600
    PNP: replace pnp_resource_table with dynamically allocated resources

    Last analysis from Bjorn was:
    > The problem seems to be that Frans has some PCI devices that are not
    > configured by the BIOS, and their BARs contain zero. A PNP quirk
    > checks for overlaps of PCI devices and PNP devices, and those zero-
    > valued BARs of course conflict with the PNP motherboard devices that
    > describe legacy hardware.
    >
    > Here's another approach based on section 3.5 of the PCI Firmware spec.
    > It says:
    >
    > Since not all devices may be configured prior to the operating
    > system handoff, the operating system needs to know whether a
    > specific BAR register has been configured by firmware. The operating
    > system makes the determination by checking the I/O Enable, and
    > Memory Enable bits in the device's command register, and Expansion
    > ROM BAR enable bits. If the enable bit is set, then the corresponding
    > resource register has been configured.
    >
    > So instead of checking whether the BAR contains zero, the patch below
    > checks the I/O, Mem, and ROM BAR enable bits to determine whether a
    > BAR is enabled.

    Below the then proposed patch from Bjorn, rediffed against 2.6.29-rc7.
    I've verified that the patch still solves the issue for me. Attached
    dmesg output for 2.6.29-rc7 without and with the patch.

    Bjorn, could you please consider this patch for inclusion again?

    Original thread: http://marc.info/?l=linux-kernel&m=122095745403793&w=4

    TIA and sorry for the confusion,
    FJP


    diff --git a/drivers/pci/setup-res.c b/drivers/pci/setup-res.c
    index 32e8d88..e63f800 100644
    --- a/drivers/pci/setup-res.c
    +++ b/drivers/pci/setup-res.c
    @@ -26,6 +26,28 @@
    #include "pci.h"


    +int pci_resource_enabled(struct pci_dev *dev, int bar)
    +{
    + u16 command = 0;
    + u32 addr = 0;
    +
    + pci_read_config_word(dev, PCI_COMMAND, &command);
    +
    + if (pci_resource_flags(dev, bar) & IORESOURCE_IO)
    + return command & PCI_COMMAND_IO;
    +
    + if (command & PCI_COMMAND_MEMORY) {
    + if (bar == PCI_ROM_RESOURCE) {
    + pci_read_config_dword(dev, dev->rom_base_reg, &addr);
    + return addr & PCI_ROM_ADDRESS_ENABLE;
    + }
    +
    + return 1;
    + }
    +
    + return 0;
    +}
    +
    void pci_update_resource(struct pci_dev *dev, int resno)
    {
    struct pci_bus_region region;
    diff --git a/drivers/pnp/quirks.c b/drivers/pnp/quirks.c
    index 8473fe5..1f37988 100644
    --- a/drivers/pnp/quirks.c
    +++ b/drivers/pnp/quirks.c
    @@ -247,6 +247,9 @@ static void quirk_system_pci_resources(struct pnp_dev *dev)
    for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) {
    unsigned long type;

    + if (!pci_resource_enabled(pdev, i))
    + continue;
    +
    type = pci_resource_flags(pdev, i) &
    (IORESOURCE_IO | IORESOURCE_MEM);
    if (!type || pci_resource_len(pdev, i) == 0)
    diff --git a/include/linux/pci.h b/include/linux/pci.h
    index c927ae9..9848ac2 100644
    --- a/include/linux/pci.h
    +++ b/include/linux/pci.h
    @@ -870,6 +870,8 @@ static inline int pci_proc_domain(struct pci_bus *bus)
    }
    #endif /* CONFIG_PCI_DOMAINS */

    +extern int pci_resource_enabled(struct pci_dev *dev, int bar);
    +
    #else /* CONFIG_PCI is not enabled */

    /*
    @@ -1050,6 +1052,9 @@ static inline struct pci_dev *pci_get_bus_and_slot(unsigned int bus,
    unsigned int devfn)
    { return NULL; }

    +static inline int pci_resource_enabled(struct pci_dev *dev, int bar)
    +{ return 0; }
    +
    #endif /* CONFIG_PCI */

    /* Include architecture-dependent settings and functions */
    Linux version 2.6.29-rc7 (root@aragorn) (gcc version 4.3.3 (Debian 4.3.3-5) ) #25 SMP Wed Mar 4 13:04:29 CET 2009
    KERNEL supported cpus:
    Intel GenuineIntel
    AMD AuthenticAMD
    NSC Geode by NSC
    Cyrix CyrixInstead
    Centaur CentaurHauls
    Transmeta GenuineTMx86
    Transmeta TransmetaCPU
    UMC UMC UMC UMC
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e0000 - 00000000000eee00 (reserved)
    BIOS-e820: 00000000000eee00 - 00000000000ef000 (ACPI NVS)
    BIOS-e820: 00000000000ef000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001ef40000 (usable)
    BIOS-e820: 000000001ef40000 - 000000001ef50000 (ACPI data)
    BIOS-e820: 000000001ef50000 - 000000001f000000 (reserved)
    BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
    BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved)
    BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
    BIOS-e820: 00000000ffe80000 - 0000000100000000 (reserved)
    DMI 2.3 present.
    last_pfn = 0x1ef40 max_arch_pfn = 0x100000
    x86 PAT enabled: cpu 0, old 0x7010600070106, new 0x7010600070106
    kernel direct mapping tables up to 1ef40000 @ 7000-c000
    RAMDISK: 1eb65000 - 1ef2f4b4
    ACPI: RSDP 000F0180, 0014 (r0 TOSHIB)
    ACPI: RSDT 1EF40000, 0038 (r1 TOSHIB 750 970814 TASM 4010000)
    ACPI: FACP 1EF40060, 0084 (r2 TOSHIB 750 20030101 TASM 4010000)
    FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4)
    ACPI: DSDT 1EF40558, 4B72 (r1 TOSHIB A000C 20031216 MSFT 100000E)
    ACPI: FACS 000EEE00, 0040
    ACPI: SSDT 1EF402CA, 0082 (r1 TOSHIB A000C 20030917 MSFT 100000E)
    ACPI: DBGP 1EF400E4, 0034 (r1 TOSHIB 750 970814 TASM 4010000)
    ACPI: BOOT 1EF40038, 0028 (r1 TOSHIB 750 970814 TASM 4010000)
    ACPI: APIC 1EF40118, 0062 (r1 TOSHIB 750 970814 TASM 4010000)
    ACPI: Local APIC address 0xfee00000
    0MB HIGHMEM available.
    495MB LOWMEM available.
    mapped low ram: 0 - 1ef40000
    low ram: 00000000 - 1ef40000
    bootmap 00002000 - 00005de8
    (9 early reservations) ==> bootmem [0000000000 - 001ef40000]
    #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
    #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
    #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
    #3 [0000100000 - 0000498804] TEXT DATA BSS ==> [0000100000 - 0000498804]
    #4 [001eb65000 - 001ef2f4b4] RAMDISK ==> [001eb65000 - 001ef2f4b4]
    #5 [0000499000 - 000049c000] INIT_PG_TABLE ==> [0000499000 - 000049c000]
    #6 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
    #7 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
    #8 [0000002000 - 0000006000] BOOTMAP ==> [0000002000 - 0000006000]
    Zone PFN ranges:
    DMA 0x00000000 -> 0x00001000
    Normal 0x00001000 -> 0x0001ef40
    HighMem 0x0001ef40 -> 0x0001ef40
    Movable zone start PFN for each node
    early_node_map[2] active PFN ranges
    0: 0x00000000 -> 0x0000009f
    0: 0x00000100 -> 0x0001ef40
    On node 0 totalpages: 126687
    free_area_init_node: node 0, pgdat c03cf520, node_mem_map c1000000
    DMA zone: 32 pages used for memmap
    DMA zone: 0 pages reserved
    DMA zone: 3967 pages, LIFO batch:0
    Normal zone: 959 pages used for memmap
    Normal zone: 121729 pages, LIFO batch:31
    ACPI: PM-Timer IO Port: 0xd808
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
    ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Enabling APIC mode: Flat. Using 1 I/O APICs
    Using ACPI (MADT) for SMP configuration information
    SMP: Allowing 2 CPUs, 1 hotplug CPUs
    nr_irqs_gsi: 24
    PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
    PM: Registered nosave memory: 00000000000e0000 - 00000000000ee000
    PM: Registered nosave memory: 00000000000ee000 - 00000000000ef000
    PM: Registered nosave memory: 00000000000ef000 - 0000000000100000
    Allocating PCI resources starting at 20000000 (gap: 1f000000:dfc00000)
    NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
    PERCPU: Allocating 32768 bytes of per cpu data
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125696
    Kernel command line: root=/dev/mapper/strider-root ro vga=791 quiet
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    PID hash table entries: 2048 (order: 11, 8192 bytes)
    TSC: PIT calibration matches PMTIMER. 1 loops
    Detected 2793.043 MHz processor.
    Console: colour dummy device 80x25
    console [tty0] enabled
    Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Memory: 494568k/507136k available (1860k kernel code, 12052k reserved, 1112k data, 268k init, 0k highmem)
    virtual kernel memory layout:
    fixmap : 0xfff51000 - 0xfffff000 ( 696 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xdf740000 - 0xff7fe000 ( 512 MB)
    lowmem : 0xc0000000 - 0xdef40000 ( 495 MB)
    .init : 0xc03ef000 - 0xc0432000 ( 268 kB)
    .data : 0xc02d127d - 0xc03e75ec (1112 kB)
    .text : 0xc0100000 - 0xc02d127d (1860 kB)
    Checking if this processor honours the WP bit even in supervisor mode...Ok.
    Calibrating delay loop (skipped), value calculated using timer frequency.. 5586.08 BogoMIPS (lpj=11172172)
    Security Framework initialized
    SELinux: Disabled at boot.
    Mount-cache hash table entries: 512
    CPU: Trace cache: 12K uops, L1 D cache: 8K
    CPU: L2 cache: 512K
    [ds] using Netburst configuration
    CPU: Hyper-Threading is disabled
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
    CPU0: Thermal monitoring enabled
    Checking 'hlt' instruction... OK.
    SMP alternatives: switching to UP code
    ACPI: Core revision 20081204
    ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    CPU0: Mobile Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
    Brought up 1 CPUs
    Total of 1 processors activated (5586.08 BogoMIPS).
    CPU0 attaching NULL sched-domain.
    net_namespace: 996 bytes
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: PCI BIOS revision 2.10 entry at 0xfd2fe, last bus=3
    PCI: Using configuration type 1 for base access
    bio: create slab <bio-0> at 0
    ACPI: EC: Look up EC in DSDT
    ACPI Warning (dsobject-0502): Package List length (F) larger than NumElements count (2), truncated
    [20081204]
    ACPI: Interpreter enabled
    ACPI: (supports S0 S3 S4 S5)
    ACPI: Using IOAPIC for interrupt routing
    ACPI: No dock devices found.
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    pci 0000:00:02.0: reg 10 32bit mmio: [0xd8000000-0xdfffffff]
    pci 0000:00:02.0: reg 14 32bit mmio: [0xd0000000-0xd007ffff]
    pci 0000:00:02.0: reg 18 io port: [0xeff8-0xefff]
    pci 0000:00:02.0: supports D1
    pci 0000:00:02.1: reg 10 32bit mmio: [0x20000000-0x27ffffff]
    pci 0000:00:02.1: reg 14 32bit mmio: [0x2c000000-0x2c07ffff]
    pci 0000:00:02.1: supports D1
    pci 0000:00:1d.0: reg 20 io port: [0xcfe0-0xcfff]
    pci 0000:00:1d.1: reg 20 io port: [0xcf80-0xcf9f]
    pci 0000:00:1d.7: reg 10 32bit mmio: [0x000000-0x0003ff]
    pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    pci 0000:00:1d.7: PME# disabled
    HPET not enabled in BIOS. You might try hpet=force boot option
    pci 0000:00:1f.0: quirk: region d800-d87f claimed by ICH4 ACPI/GPIO/TCO
    pci 0000:00:1f.0: quirk: region eec0-eeff claimed by ICH4 GPIO
    pci 0000:00:1f.1: reg 10 io port: [0xbff8-0xbfff]
    pci 0000:00:1f.1: reg 14 io port: [0xbff4-0xbff7]
    pci 0000:00:1f.1: reg 18 io port: [0xbfe8-0xbfef]
    pci 0000:00:1f.1: reg 1c io port: [0xbfe4-0xbfe7]
    pci 0000:00:1f.1: reg 20 io port: [0xbfa0-0xbfaf]
    pci 0000:00:1f.1: reg 24 32bit mmio: [0x2c080400-0x2c0807ff]
    pci 0000:00:1f.5: reg 10 io port: [0x00-0xff]
    pci 0000:00:1f.5: reg 14 io port: [0x00-0x3f]
    pci 0000:00:1f.5: reg 18 32bit mmio: [0x000000-0x0001ff]
    pci 0000:00:1f.5: reg 1c 32bit mmio: [0x000000-0x0000ff]
    pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
    pci 0000:00:1f.5: PME# disabled
    pci 0000:00:1f.6: reg 10 io port: [0x00-0xff]
    pci 0000:00:1f.6: reg 14 io port: [0x00-0x7f]
    pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold
    pci 0000:00:1f.6: PME# disabled
    pci 0000:01:08.0: reg 10 32bit mmio: [0xcffff000-0xcfffffff]
    pci 0000:01:08.0: reg 14 io port: [0xcf40-0xcf7f]
    pci 0000:01:08.0: supports D1 D2
    pci 0000:01:08.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:01:08.0: PME# disabled
    pci 0000:01:0b.0: reg 10 32bit mmio: [0x000000-0x000fff]
    pci 0000:00:1e.0: transparent bridge
    pci 0000:00:1e.0: bridge io port: [0xc000-0xcfff]
    pci 0000:00:1e.0: bridge 32bit mmio: [0xcff00000-0xcfffffff]
    pci_bus 0000:00: on NUMA node 0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *11)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *11)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *11)
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *11)
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *11)
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *11)
    ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11)
    ACPI: Power Resource [PFAN] (off)
    PCI: Using ACPI for IRQ routing
    pci 0000:00:1d.0: BAR 4: can't allocate resource
    pci 0000:00:1d.1: BAR 4: can't allocate resource
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp 00:08: io resource (0x10-0x1f) overlaps 0000:00:1d.0 BAR 4 (0x0-0x1f), disabling
    pnp 00:08: io resource (0x10-0x1f) overlaps 0000:00:1d.1 BAR 4 (0x0-0x1f), disabling
    pnp 00:08: io resource (0x2e-0x2f) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x62-0x62) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x66-0x66) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x80-0x80) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x84-0x86) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x88-0x88) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x8c-0x8e) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0xe0-0xef) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x10-0x1f) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x24-0x25) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x28-0x29) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x2c-0x2d) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x30-0x31) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x34-0x35) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x38-0x39) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x3c-0x3d) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x50-0x53) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x63-0x63) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x65-0x65) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x72-0x77) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x90-0x9f) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0xa4-0xa5) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0xa8-0xa9) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0xac-0xad) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0xb0-0xb5) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0xb8-0xb9) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0xbc-0xbd) overlaps 0000:00:1f.5 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x2e-0x2f) overlaps 0000:00:1f.5 BAR 1 (0x0-0x3f), disabling
    pnp 00:08: io resource (0x10-0x1f) overlaps 0000:00:1f.5 BAR 1 (0x0-0x3f), disabling
    pnp 00:08: io resource (0x24-0x25) overlaps 0000:00:1f.5 BAR 1 (0x0-0x3f), disabling
    pnp 00:08: io resource (0x28-0x29) overlaps 0000:00:1f.5 BAR 1 (0x0-0x3f), disabling
    pnp 00:08: io resource (0x2c-0x2d) overlaps 0000:00:1f.5 BAR 1 (0x0-0x3f), disabling
    pnp 00:08: io resource (0x30-0x31) overlaps 0000:00:1f.5 BAR 1 (0x0-0x3f), disabling
    pnp 00:08: io resource (0x34-0x35) overlaps 0000:00:1f.5 BAR 1 (0x0-0x3f), disabling
    pnp 00:08: io resource (0x38-0x39) overlaps 0000:00:1f.5 BAR 1 (0x0-0x3f), disabling
    pnp 00:08: io resource (0x3c-0x3d) overlaps 0000:00:1f.5 BAR 1 (0x0-0x3f), disabling
    pnp 00:08: io resource (0x2e-0x2f) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x62-0x62) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x66-0x66) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x80-0x80) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x84-0x86) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x88-0x88) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x8c-0x8e) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0xe0-0xef) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x10-0x1f) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x24-0x25) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x28-0x29) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x2c-0x2d) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x30-0x31) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x34-0x35) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x38-0x39) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x3c-0x3d) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x50-0x53) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x63-0x63) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x65-0x65) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x72-0x77) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x90-0x9f) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0xa4-0xa5) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0xa8-0xa9) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0xac-0xad) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0xb0-0xb5) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0xb8-0xb9) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0xbc-0xbd) overlaps 0000:00:1f.6 BAR 0 (0x0-0xff), disabling
    pnp 00:08: io resource (0x2e-0x2f) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp 00:08: io resource (0x62-0x62) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp 00:08: io resource (0x66-0x66) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp 00:08: io resource (0x10-0x1f) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp 00:08: io resource (0x24-0x25) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp 00:08: io resource (0x28-0x29) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp 00:08: io resource (0x2c-0x2d) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp 00:08: io resource (0x30-0x31) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp 00:08: io resource (0x34-0x35) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp 00:08: io resource (0x38-0x39) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp 00:08: io resource (0x3c-0x3d) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp 00:08: io resource (0x50-0x53) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp 00:08: io resource (0x63-0x63) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp 00:08: io resource (0x65-0x65) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp 00:08: io resource (0x72-0x77) overlaps 0000:00:1f.6 BAR 1 (0x0-0x7f), disabling
    pnp: PnP ACPI: found 10 devices
    ACPI: ACPI bus type pnp unregistered
    PnPBIOS: Disabled by ACPI PNP
    system 00:00: iomem range 0x0-0x9ffff could not be reserved
    system 00:00: iomem range 0xe0000-0xeffff could not be reserved
    system 00:00: iomem range 0xf0000-0xfffff could not be reserved
    system 00:00: iomem range 0x100000-0x1ef3ffff could not be reserved
    system 00:00: iomem range 0x1ef40000-0x1ef4ffff could not be reserved
    system 00:00: iomem range 0x1ef50000-0x1effffff has been reserved
    system 00:00: iomem range 0xfec10000-0xfec1ffff has been reserved
    system 00:00: iomem range 0xfeda0000-0xfedbffff has been reserved
    system 00:00: iomem range 0xfec00000-0xfec00fff has been reserved
    system 00:00: iomem range 0xfee00000-0xfee00fff has been reserved
    system 00:00: iomem range 0xffb00000-0xffbfffff has been reserved
    system 00:00: iomem range 0xffe80000-0xffffffff has been reserved
    system 00:08: ioport range 0x1e0-0x1ef has been reserved
    system 00:08: ioport range 0x480-0x48f has been reserved
    system 00:08: ioport range 0x680-0x6ff has been reserved
    system 00:08: ioport range 0x800-0x80f has been reserved
    system 00:08: ioport range 0xd800-0xd87f has been reserved
    system 00:08: ioport range 0xd880-0xd89f has been reserved
    system 00:08: ioport range 0xd8a0-0xd8bf has been reserved
    system 00:08: ioport range 0xe000-0xe07f has been reserved
    system 00:08: ioport range 0xe080-0xe0ff has been reserved
    system 00:08: ioport range 0xe400-0xe47f has been reserved
    system 00:08: ioport range 0xe480-0xe4ff has been reserved
    system 00:08: ioport range 0xe800-0xe87f has been reserved
    system 00:08: ioport range 0xe880-0xe8ff has been reserved
    system 00:08: ioport range 0xec00-0xec7f has been reserved
    system 00:08: ioport range 0xec80-0xecff has been reserved
    system 00:08: ioport range 0xeeac-0xeeac has been reserved
    system 00:08: ioport range 0xeeb0-0xeebf has been reserved
    system 00:08: ioport range 0xeec0-0xeeff has been reserved
    system 00:08: ioport range 0x4d0-0x4d1 has been reserved
    pci 0000:01:0b.0: CardBus bridge, secondary bus 0000:02
    pci 0000:01:0b.0: IO window: 0x00c000-0x00c0ff
    pci 0000:01:0b.0: IO window: 0x00c400-0x00c4ff
    pci 0000:01:0b.0: PREFETCH window: 0x28000000-0x2bffffff
    pci 0000:01:0b.0: MEM window: 0x30000000-0x33ffffff
    pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
    pci 0000:00:1e.0: IO window: 0xc000-0xcfff
    pci 0000:00:1e.0: MEM window: 0xcff00000-0xcfffffff
    pci 0000:00:1e.0: PREFETCH window: 0x00000028000000-0x0000002bffffff
    pci 0000:00:1e.0: setting latency timer to 64
    pci 0000:01:0b.0: enabling device (0000 -> 0003)
    pci 0000:01:0b.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    pci_bus 0000:00: resource 0 io: [0x00-0xffff]
    pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
    pci_bus 0000:01: resource 0 io: [0xc000-0xcfff]
    pci_bus 0000:01: resource 1 mem: [0xcff00000-0xcfffffff]
    pci_bus 0000:01: resource 2 mem: [0x28000000-0x2bffffff]
    pci_bus 0000:01: resource 3 io: [0x00-0xffff]
    pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffff]
    pci_bus 0000:02: resource 0 io: [0xc000-0xc0ff]
    pci_bus 0000:02: resource 1 io: [0xc400-0xc4ff]
    pci_bus 0000:02: resource 2 mem: [0x28000000-0x2bffffff]
    pci_bus 0000:02: resource 3 mem: [0x30000000-0x33ffffff]
    NET: Registered protocol family 2
    IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
    TCP: Hash tables configured (established 16384 bind 16384)
    TCP reno registered
    NET: Registered protocol family 1
    checking if image is initramfs... it is
    Freeing initrd memory: 3881k freed
    Simple Boot Flag at 0x7c set to 0x1
    audit: initializing netlink socket (disabled)
    type=2000 audit(1236175417.524:1): initialized
    VFS: Disk quotas dquot_6.5.2
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    msgmni has been set to 973
    alg: No test for stdrng (krng)
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    pci 0000:00:02.0: Boot video device
    pci 0000:01:08.0: Firmware left e100 interrupts enabled; disabling
    vesafb: framebuffer at 0xd8000000, mapped to 0xdf780000, using 3072k, total 16192k
    vesafb: mode is 1024x768x16, linelength=2048, pages=9
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    Console: switching to colour frame buffer device 128x48
    fb0: VESA VGA frame buffer device
    isapnp: Scanning for PnP cards...
    Switched to high resolution mode on CPU 0
    isapnp: No Plug & Play device found
    Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
    serial 0000:00:1f.6: power state changed by ACPI to D0
    serial 0000:00:1f.6: enabling device (0000 -> 0001)
    serial 0000:00:1f.6: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    serial 0000:00:1f.6: PCI INT B disabled
    brd: module loaded
    e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI
    e100: Copyright(c) 1999-2006 Intel Corporation
    e100 0000:01:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    e100 0000:01:08.0: PME# disabled
    e100: eth0: e100_probe: addr 0xcffff000, irq 20, MAC addr 00:08:0d:17:bf:f5
    console [netcon0] enabled
    netconsole: network logging started
    PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    cpuidle: using governor ladder
    cpuidle: using governor menu
    TCP bic registered
    NET: Registered protocol family 17
    Using IPI No-Shortcut mode
    Freeing unused kernel memory: 268k freed
    input: AT Translated Set 2 keyboard as /class/input/input0
    fan PNP0C0B:00: registered as cooling_device0
    ACPI: Fan [FAN] (off)
    ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    processor ACPI_CPU:00: registered as cooling_device1
    thermal LNXTHERM:01: registered as thermal_zone0
    ACPI: Thermal Zone [THRM] (58 C)
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    ehci_hcd 0000:00:1d.7: enabling device (0000 -> 0002)
    ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
    ehci_hcd 0000:00:1d.7: setting latency timer to 64
    ehci_hcd 0000:00:1d.7: EHCI Host Controller
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:1d.7: debug port 1
    ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
    ehci_hcd 0000:00:1d.7: irq 23, io mem 0x2c080000
    uhci_hcd: USB Universal Host Controller Interface driver
    ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 6 ports detected
    uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    uhci_hcd 0000:00:1d.0: setting latency timer to 64
    uhci_hcd 0000:00:1d.0: UHCI Host Controller
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:1d.0: irq 16, io base 0x000018c0
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
    uhci_hcd 0000:00:1d.1: setting latency timer to 64
    uhci_hcd 0000:00:1d.1: UHCI Host Controller
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1d.1: irq 19, io base 0x000018e0
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    Uniform Multi-Platform E-IDE driver
    piix 0000:00:1f.1: IDE controller (0x8086:0x24ca rev 0x03)
    PIIX_IDE 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    piix 0000:00:1f.1: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xbfa0-0xbfa7
    ide1: BM-DMA at 0xbfa8-0xbfaf
    Probing IDE interface ide0...
    Marking TSC unstable due to TSC halts in idle
    hda: HTS541080G9AT00, ATA DISK drive
    hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
    hda: UDMA/100 mode selected
    Probing IDE interface ide1...
    Clocksource tsc unstable (delta = -496610873 ns)
    hdc: TOSHIBA DVD-ROM SD-R6112, ATAPI CD/DVD-ROM drive
    hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
    hdc: UDMA/33 mode selected
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    ide1 at 0x170-0x177,0x376 on irq 15
    SCSI subsystem initialized
    libata version 3.00 loaded.
    ide-gd driver 1.18
    hda: max request size: 512KiB
    ide-cd driver 5.00
    hda: 156301488 sectors (80026 MB) w/7539KiB Cache, CHS=16383/255/63
    hda: cache flushes supported
    hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
    ide-cd: hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
    Uniform CD-ROM driver Revision: 3.20
    device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
    kjournald starting. Commit interval 5 seconds
    EXT3-fs: mounted filesystem with ordered data mode.
    udevd version 125 started
    input: Power Button (FF) as /class/input/input1
    ACPI: Power Button (FF) [PWRF]
    input: Lid Switch as /class/input/input2
    ACPI: Lid Switch [LID]
    input: Power Button (CM) as /class/input/input3
    ACPI: Power Button (CM) [PWRB]
    ACPI Warning (nspredef-0940): \_SB_.BAT1._BIF: Return Package type mismatch at index 12 - found Integer, expected String/Buffer [20081204]
    ACPI: Battery Slot [BAT1] (battery present)
    ACPI: AC Adapter [ADP1] (on-line)
    Linux agpgart interface v0.103
    acpi device:0f: registered as cooling_device2
    input: Video Bus as /class/input/input4
    ACPI: Video Device [VGA] (multi-head: yes rom: yes post: no)
    parport_pc 00:09: activated
    parport_pc 00:09: reported by Plug and Play ACPI
    parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
    iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
    iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0xd860)
    iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    input: PC Speaker as /class/input/input5
    agpgart-intel 0000:00:00.0: Intel 855GM Chipset
    agpgart-intel 0000:00:00.0: detected 16252K stolen memory
    agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xd8000000
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    rtc_cmos 00:07: RTC can wake from S4
    rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one year, 114 bytes nvram
    toshiba_acpi: Toshiba Laptop ACPI Extras version 0.19
    toshiba_acpi: HCI method: \_SB_.VALZ.GHCI
    yenta_cardbus 0000:01:0b.0: CardBus bridge found [1179:0001]
    yenta_cardbus 0000:01:0b.0: ISA IRQ mask 0x0c38, PCI irq 18
    yenta_cardbus 0000:01:0b.0: Socket status: 30000020
    yenta_cardbus 0000:01:0b.0: pcmcia: parent PCI bridge I/O window: 0xc000 - 0xcfff
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc000-0xcfff: clean.
    yenta_cardbus 0000:01:0b.0: pcmcia: parent PCI bridge Memory window: 0xcff00000 - 0xcfffffff
    yenta_cardbus 0000:01:0b.0: pcmcia: parent PCI bridge Memory window: 0x28000000 - 0x2bffffff
    Intel ICH 0000:00:1f.5: power state changed by ACPI to D0
    Intel ICH 0000:00:1f.5: enabling device (0000 -> 0003)
    Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    Intel ICH 0000:00:1f.5: setting latency timer to 64
    input: PS/2 Mouse as /class/input/input6
    input: AlpsPS/2 ALPS GlidePoint as /class/input/input7
    pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
    pci 0000:02:00.0: reg 10 32bit mmio: [0x000000-0x00ffff]
    cfg80211: Using static regulatory domain info
    cfg80211: Regulatory domain: EU
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2482000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
    (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
    (5490000 KHz - 5710000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
    ath5k 0000:02:00.0: enabling device (0000 -> 0002)
    ath5k 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    ath5k 0000:02:00.0: registered as 'phy0'
    wmaster0 (ath5k): not using net_device_ops yet
    phy0: Selected rate control algorithm 'minstrel'
    wlan0 (ath5k): not using net_device_ops yet
    ath5k phy0: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43)
    ath5k phy0: RF2112B 2GHz radio found (0x46)
    udev: renamed network interface wlan0 to ath0
    intel8x0_measure_ac97_clock: measured 55377 usecs
    intel8x0: clocking to 48000
    Intel ICH Modem 0000:00:1f.6: power state changed by ACPI to D0
    Intel ICH Modem 0000:00:1f.6: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    Intel ICH Modem 0000:00:1f.6: setting latency timer to 64
    EXT3 FS on dm-1, internal journal
    loop: module loaded
    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on dm-7, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on dm-5, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on dm-2, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on dm-3, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    Adding 1048568k swap on /dev/mapper/strider-swap_crypt. Priority:-1 extents:1 across:1048568k
    ADDRCONF(NETDEV_UP): ath0: link is not ready
    ath0: authenticate with AP 00:14:c1:38:e5:15
    ath0: authenticated
    ath0: associate with AP 00:14:c1:38:e5:15
    ath0: RX AssocResp from 00:14:c1:38:e5:15 (capab=0x411 status=0 aid=2)
    ath0: associated
    ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
    lp0: using parport0 (interrupt-driven).
    ppdev: user-space parallel port driver
    ADDRCONF(NETDEV_UP): eth0: link is not ready
    ath0: no IPv6 routers present
    ADDRCONF(NETDEV_UP): eth0: link is not ready
    CPU0 attaching NULL sched-domain.
    CPU0 attaching NULL sched-domain.
    Linux version 2.6.29-rc7 (root@aragorn) (gcc version 4.3.3 (Debian 4.3.3-5) ) #10 SMP Wed Mar 4 20:32:19 CET 2009
    KERNEL supported cpus:
    Intel GenuineIntel
    AMD AuthenticAMD
    NSC Geode by NSC
    Cyrix CyrixInstead
    Centaur CentaurHauls
    Transmeta GenuineTMx86
    Transmeta TransmetaCPU
    UMC UMC UMC UMC
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e0000 - 00000000000eee00 (reserved)
    BIOS-e820: 00000000000eee00 - 00000000000ef000 (ACPI NVS)
    BIOS-e820: 00000000000ef000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001ef40000 (usable)
    BIOS-e820: 000000001ef40000 - 000000001ef50000 (ACPI data)
    BIOS-e820: 000000001ef50000 - 000000001f000000 (reserved)
    BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
    BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved)
    BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
    BIOS-e820: 00000000ffe80000 - 0000000100000000 (reserved)
    DMI 2.3 present.
    last_pfn = 0x1ef40 max_arch_pfn = 0x100000
    x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    kernel direct mapping tables up to 1ef40000 @ 7000-c000
    RAMDISK: 1eb65000 - 1ef2f40f
    ACPI: RSDP 000F0180, 0014 (r0 TOSHIB)
    ACPI: RSDT 1EF40000, 0038 (r1 TOSHIB 750 970814 TASM 4010000)
    ACPI: FACP 1EF40060, 0084 (r2 TOSHIB 750 20030101 TASM 4010000)
    FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4)
    ACPI: DSDT 1EF40558, 4B72 (r1 TOSHIB A000C 20031216 MSFT 100000E)
    ACPI: FACS 000EEE00, 0040
    ACPI: SSDT 1EF402CA, 0082 (r1 TOSHIB A000C 20030917 MSFT 100000E)
    ACPI: DBGP 1EF400E4, 0034 (r1 TOSHIB 750 970814 TASM 4010000)
    ACPI: BOOT 1EF40038, 0028 (r1 TOSHIB 750 970814 TASM 4010000)
    ACPI: APIC 1EF40118, 0062 (r1 TOSHIB 750 970814 TASM 4010000)
    ACPI: Local APIC address 0xfee00000
    0MB HIGHMEM available.
    495MB LOWMEM available.
    mapped low ram: 0 - 1ef40000
    low ram: 00000000 - 1ef40000
    bootmap 00002000 - 00005de8
    (9 early reservations) ==> bootmem [0000000000 - 001ef40000]
    #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
    #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
    #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
    #3 [0000100000 - 0000498804] TEXT DATA BSS ==> [0000100000 - 0000498804]
    #4 [001eb65000 - 001ef2f40f] RAMDISK ==> [001eb65000 - 001ef2f40f]
    #5 [0000499000 - 000049c000] INIT_PG_TABLE ==> [0000499000 - 000049c000]
    #6 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
    #7 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
    #8 [0000002000 - 0000006000] BOOTMAP ==> [0000002000 - 0000006000]
    Zone PFN ranges:
    DMA 0x00000000 -> 0x00001000
    Normal 0x00001000 -> 0x0001ef40
    HighMem 0x0001ef40 -> 0x0001ef40
    Movable zone start PFN for each node
    early_node_map[2] active PFN ranges
    0: 0x00000000 -> 0x0000009f
    0: 0x00000100 -> 0x0001ef40
    On node 0 totalpages: 126687
    free_area_init_node: node 0, pgdat c03cf520, node_mem_map c1000000
    DMA zone: 32 pages used for memmap
    DMA zone: 0 pages reserved
    DMA zone: 3967 pages, LIFO batch:0
    Normal zone: 959 pages used for memmap
    Normal zone: 121729 pages, LIFO batch:31
    ACPI: PM-Timer IO Port: 0xd808
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
    ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Enabling APIC mode: Flat. Using 1 I/O APICs
    Using ACPI (MADT) for SMP configuration information
    SMP: Allowing 2 CPUs, 1 hotplug CPUs
    nr_irqs_gsi: 24
    PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
    PM: Registered nosave memory: 00000000000e0000 - 00000000000ee000
    PM: Registered nosave memory: 00000000000ee000 - 00000000000ef000
    PM: Registered nosave memory: 00000000000ef000 - 0000000000100000
    Allocating PCI resources starting at 20000000 (gap: 1f000000:dfc00000)
    NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
    PERCPU: Allocating 32768 bytes of per cpu data
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125696
    Kernel command line: root=/dev/mapper/strider-root rootdelay=10 ro vga=791 quiet
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    PID hash table entries: 2048 (order: 11, 8192 bytes)
    Fast TSC calibration using PIT
    Detected 2793.051 MHz processor.
    Console: colour dummy device 80x25
    console [tty0] enabled
    Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Memory: 494568k/507136k available (1860k kernel code, 12052k reserved, 1112k data, 268k init, 0k highmem)
    virtual kernel memory layout:
    fixmap : 0xfff51000 - 0xfffff000 ( 696 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xdf740000 - 0xff7fe000 ( 512 MB)
    lowmem : 0xc0000000 - 0xdef40000 ( 495 MB)
    .init : 0xc03ef000 - 0xc0432000 ( 268 kB)
    .data : 0xc02d130d - 0xc03e75ec (1112 kB)
    .text : 0xc0100000 - 0xc02d130d (1860 kB)
    Checking if this processor honours the WP bit even in supervisor mode...Ok.
    Calibrating delay loop (skipped), value calculated using timer frequency.. 5586.10 BogoMIPS (lpj=11172204)
    Security Framework initialized
    SELinux: Disabled at boot.
    Mount-cache hash table entries: 512
    CPU: Trace cache: 12K uops, L1 D cache: 8K
    CPU: L2 cache: 512K
    [ds] using Netburst configuration
    CPU: Hyper-Threading is disabled
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
    CPU0: Thermal monitoring enabled
    Checking 'hlt' instruction... OK.
    SMP alternatives: switching to UP code
    ACPI: Core revision 20081204
    ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    CPU0: Mobile Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
    Brought up 1 CPUs
    Total of 1 processors activated (5586.10 BogoMIPS).
    CPU0 attaching NULL sched-domain.
    net_namespace: 996 bytes
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: PCI BIOS revision 2.10 entry at 0xfd2fe, last bus=3
    PCI: Using configuration type 1 for base access
    bio: create slab <bio-0> at 0
    ACPI: EC: Look up EC in DSDT
    ACPI Warning (dsobject-0502): Package List length (F) larger than NumElements count (2), truncated
    [20081204]
    ACPI: Interpreter enabled
    ACPI: (supports S0 S3 S4 S5)
    ACPI: Using IOAPIC for interrupt routing
    ACPI: No dock devices found.
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    pci 0000:00:02.0: reg 10 32bit mmio: [0xd8000000-0xdfffffff]
    pci 0000:00:02.0: reg 14 32bit mmio: [0xd0000000-0xd007ffff]
    pci 0000:00:02.0: reg 18 io port: [0xeff8-0xefff]
    pci 0000:00:02.0: supports D1
    pci 0000:00:02.1: reg 10 32bit mmio: [0x000000-0x7ffffff]
    pci 0000:00:02.1: reg 14 32bit mmio: [0x000000-0x07ffff]
    pci 0000:00:02.1: supports D1
    pci 0000:00:1d.0: reg 20 io port: [0xcfe0-0xcfff]
    pci 0000:00:1d.1: reg 20 io port: [0xcf80-0xcf9f]
    pci 0000:00:1d.7: reg 10 32bit mmio: [0x000000-0x0003ff]
    pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    pci 0000:00:1d.7: PME# disabled
    HPET not enabled in BIOS. You might try hpet=force boot option
    pci 0000:00:1f.0: quirk: region d800-d87f claimed by ICH4 ACPI/GPIO/TCO
    pci 0000:00:1f.0: quirk: region eec0-eeff claimed by ICH4 GPIO
    pci 0000:00:1f.1: reg 10 io port: [0xbff8-0xbfff]
    pci 0000:00:1f.1: reg 14 io port: [0xbff4-0xbff7]
    pci 0000:00:1f.1: reg 18 io port: [0xbfe8-0xbfef]
    pci 0000:00:1f.1: reg 1c io port: [0xbfe4-0xbfe7]
    pci 0000:00:1f.1: reg 20 io port: [0xbfa0-0xbfaf]
    pci 0000:00:1f.1: reg 24 32bit mmio: [0x000000-0x0003ff]
    pci 0000:00:1f.5: reg 10 io port: [0x00-0xff]
    pci 0000:00:1f.5: reg 14 io port: [0x00-0x3f]
    pci 0000:00:1f.5: reg 18 32bit mmio: [0x000000-0x0001ff]
    pci 0000:00:1f.5: reg 1c 32bit mmio: [0x000000-0x0000ff]
    pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
    pci 0000:00:1f.5: PME# disabled
    pci 0000:00:1f.6: reg 10 io port: [0x00-0xff]
    pci 0000:00:1f.6: reg 14 io port: [0x00-0x7f]
    pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold
    pci 0000:00:1f.6: PME# disabled
    pci 0000:01:08.0: reg 10 32bit mmio: [0xcffff000-0xcfffffff]
    pci 0000:01:08.0: reg 14 io port: [0xcf40-0xcf7f]
    pci 0000:01:08.0: supports D1 D2
    pci 0000:01:08.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:01:08.0: PME# disabled
    pci 0000:01:0b.0: reg 10 32bit mmio: [0x000000-0x000fff]
    pci 0000:00:1e.0: transparent bridge
    pci 0000:00:1e.0: bridge io port: [0xc000-0xcfff]
    pci 0000:00:1e.0: bridge 32bit mmio: [0xcff00000-0xcfffffff]
    pci_bus 0000:00: on NUMA node 0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *11)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *11)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *11)
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *11)
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *11)
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *11)
    ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11)
    ACPI: Power Resource [PFAN] (off)
    PCI: Using ACPI for IRQ routing
    pci 0000:00:1d.0: BAR 4: can't allocate resource
    pci 0000:00:1d.1: BAR 4: can't allocate resource
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp 00:08: io resource (0x10-0x1f) overlaps 0000:00:1d.0 BAR 4 (0x0-0x1f), disabling
    pnp 00:08: io resource (0x10-0x1f) overlaps 0000:00:1d.1 BAR 4 (0x0-0x1f), disabling
    pnp: PnP ACPI: found 10 devices
    ACPI: ACPI bus type pnp unregistered
    PnPBIOS: Disabled by ACPI PNP
    system 00:00: iomem range 0x0-0x9ffff could not be reserved
    system 00:00: iomem range 0xe0000-0xeffff could not be reserved
    system 00:00: iomem range 0xf0000-0xfffff could not be reserved
    system 00:00: iomem range 0x100000-0x1ef3ffff could not be reserved
    system 00:00: iomem range 0x1ef40000-0x1ef4ffff could not be reserved
    system 00:00: iomem range 0x1ef50000-0x1effffff has been reserved
    system 00:00: iomem range 0xfec10000-0xfec1ffff has been reserved
    system 00:00: iomem range 0xfeda0000-0xfedbffff has been reserved
    system 00:00: iomem range 0xfec00000-0xfec00fff has been reserved
    system 00:00: iomem range 0xfee00000-0xfee00fff has been reserved
    system 00:00: iomem range 0xffb00000-0xffbfffff has been reserved
    system 00:00: iomem range 0xffe80000-0xffffffff has been reserved
    system 00:08: ioport range 0x1e0-0x1ef has been reserved
    system 00:08: ioport range 0x480-0x48f has been reserved
    system 00:08: ioport range 0x680-0x6ff has been reserved
    system 00:08: ioport range 0x800-0x80f has been reserved
    system 00:08: ioport range 0xd800-0xd87f has been reserved
    system 00:08: ioport range 0xd880-0xd89f has been reserved
    system 00:08: ioport range 0xd8a0-0xd8bf has been reserved
    system 00:08: ioport range 0xe000-0xe07f has been reserved
    system 00:08: ioport range 0xe080-0xe0ff has been reserved
    system 00:08: ioport range 0xe400-0xe47f has been reserved
    system 00:08: ioport range 0xe480-0xe4ff has been reserved
    system 00:08: ioport range 0xe800-0xe87f has been reserved
    system 00:08: ioport range 0xe880-0xe8ff has been reserved
    system 00:08: ioport range 0xec00-0xec7f has been reserved
    system 00:08: ioport range 0xec80-0xecff has been reserved
    system 00:08: ioport range 0xeeac-0xeeac has been reserved
    system 00:08: ioport range 0xeeb0-0xeebf has been reserved
    system 00:08: ioport range 0xeec0-0xeeff has been reserved
    system 00:08: ioport range 0x4d0-0x4d1 has been reserved
    pci 0000:01:0b.0: CardBus bridge, secondary bus 0000:02
    pci 0000:01:0b.0: IO window: 0x00c000-0x00c0ff
    pci 0000:01:0b.0: IO window: 0x00c400-0x00c4ff
    pci 0000:01:0b.0: PREFETCH window: 0x28000000-0x2bffffff
    pci 0000:01:0b.0: MEM window: 0x30000000-0x33ffffff
    pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
    pci 0000:00:1e.0: IO window: 0xc000-0xcfff
    pci 0000:00:1e.0: MEM window: 0xcff00000-0xcfffffff
    pci 0000:00:1e.0: PREFETCH window: 0x00000028000000-0x0000002bffffff
    pci 0000:00:1e.0: setting latency timer to 64
    pci 0000:01:0b.0: enabling device (0000 -> 0003)
    pci 0000:01:0b.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    pci_bus 0000:00: resource 0 io: [0x00-0xffff]
    pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
    pci_bus 0000:01: resource 0 io: [0xc000-0xcfff]
    pci_bus 0000:01: resource 1 mem: [0xcff00000-0xcfffffff]
    pci_bus 0000:01: resource 2 mem: [0x28000000-0x2bffffff]
    pci_bus 0000:01: resource 3 io: [0x00-0xffff]
    pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffff]
    pci_bus 0000:02: resource 0 io: [0xc000-0xc0ff]
    pci_bus 0000:02: resource 1 io: [0xc400-0xc4ff]
    pci_bus 0000:02: resource 2 mem: [0x28000000-0x2bffffff]
    pci_bus 0000:02: resource 3 mem: [0x30000000-0x33ffffff]
    NET: Registered protocol family 2
    IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
    TCP: Hash tables configured (established 16384 bind 16384)
    TCP reno registered
    NET: Registered protocol family 1
    checking if image is initramfs... it is
    Freeing initrd memory: 3881k freed
    Simple Boot Flag at 0x7c set to 0x1
    audit: initializing netlink socket (disabled)
    type=2000 audit(1236195728.528:1): initialized
    VFS: Disk quotas dquot_6.5.2
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    msgmni has been set to 973
    alg: No test for stdrng (krng)
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    pci 0000:00:02.0: Boot video device
    pci 0000:01:08.0: Firmware left e100 interrupts enabled; disabling
    vesafb: framebuffer at 0xd8000000, mapped to 0xdf780000, using 3072k, total 16192k
    vesafb: mode is 1024x768x16, linelength=2048, pages=9
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    Console: switching to colour frame buffer device 128x48
    fb0: VESA VGA frame buffer device
    isapnp: Scanning for PnP cards...
    Switched to high resolution mode on CPU 0
    isapnp: No Plug & Play device found
    Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
    serial 0000:00:1f.6: power state changed by ACPI to D0
    serial 0000:00:1f.6: enabling device (0000 -> 0001)
    serial 0000:00:1f.6: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    serial 0000:00:1f.6: PCI INT B disabled
    brd: module loaded
    e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI
    e100: Copyright(c) 1999-2006 Intel Corporation
    e100 0000:01:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    e100 0000:01:08.0: PME# disabled
    e100: eth0: e100_probe: addr 0xcffff000, irq 20, MAC addr 00:08:0d:17:bf:f5
    console [netcon0] enabled
    netconsole: network logging started
    PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    cpuidle: using governor ladder
    cpuidle: using governor menu
    TCP bic registered
    NET: Registered protocol family 17
    Using IPI No-Shortcut mode
    Freeing unused kernel memory: 268k freed
    input: AT Translated Set 2 keyboard as /class/input/input0
    fan PNP0C0B:00: registered as cooling_device0
    ACPI: Fan [FAN] (off)
    ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    processor ACPI_CPU:00: registered as cooling_device1
    thermal LNXTHERM:01: registered as thermal_zone0
    ACPI: Thermal Zone [THRM] (33 C)
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    ehci_hcd 0000:00:1d.7: enabling device (0000 -> 0002)
    ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
    ehci_hcd 0000:00:1d.7: setting latency timer to 64
    ehci_hcd 0000:00:1d.7: EHCI Host Controller
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:1d.7: debug port 1
    ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
    ehci_hcd 0000:00:1d.7: irq 23, io mem 0x2c080000
    uhci_hcd: USB Universal Host Controller Interface driver
    ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 6 ports detected
    uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    uhci_hcd 0000:00:1d.0: setting latency timer to 64
    uhci_hcd 0000:00:1d.0: UHCI Host Controller
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:1d.0: irq 16, io base 0x000018c0
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
    uhci_hcd 0000:00:1d.1: setting latency timer to 64
    uhci_hcd 0000:00:1d.1: UHCI Host Controller
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1d.1: irq 19, io base 0x000018e0
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    Uniform Multi-Platform E-IDE driver
    piix 0000:00:1f.1: IDE controller (0x8086:0x24ca rev 0x03)
    PIIX_IDE 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    piix 0000:00:1f.1: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xbfa0-0xbfa7
    ide1: BM-DMA at 0xbfa8-0xbfaf
    Probing IDE interface ide0...
    Marking TSC unstable due to TSC halts in idle
    hda: HTS541080G9AT00, ATA DISK drive
    hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
    hda: UDMA/100 mode selected
    Probing IDE interface ide1...
    Clocksource tsc unstable (delta = -496546074 ns)
    hdc: TOSHIBA DVD-ROM SD-R6112, ATAPI CD/DVD-ROM drive
    hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
    hdc: UDMA/33 mode selected
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    ide1 at 0x170-0x177,0x376 on irq 15
    SCSI subsystem initialized
    libata version 3.00 loaded.
    ide-gd driver 1.18
    hda: max request size: 512KiB
    ide-cd driver 5.00
    hda: 156301488 sectors (80026 MB) w/7539KiB Cache, CHS=16383/255/63
    hda: cache flushes supported
    hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
    ide-cd: hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
    Uniform CD-ROM driver Revision: 3.20
    device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
    kjournald starting. Commit interval 5 seconds
    EXT3-fs: mounted filesystem with ordered data mode.
    udevd version 125 started
    Linux agpgart interface v0.103
    input: Power Button (FF) as /class/input/input1
    ACPI: Power Button (FF) [PWRF]
    input: Lid Switch as /class/input/input2
    ACPI: Lid Switch [LID]
    input: Power Button (CM) as /class/input/input3
    ACPI: Power Button (CM) [PWRB]
    ACPI: AC Adapter [ADP1] (on-line)
    ACPI Warning (nspredef-0940): \_SB_.BAT1._BIF: Return Package type mismatch at index 12 - found Integer, expected String/Buffer [20081204]
    ACPI: Battery Slot [BAT1] (battery present)
    agpgart-intel 0000:00:00.0: Intel 855GM Chipset
    agpgart-intel 0000:00:00.0: detected 16252K stolen memory
    agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xd8000000
    acpi device:0f: registered as cooling_device2
    input: Video Bus as /class/input/input4
    ACPI: Video Device [VGA] (multi-head: yes rom: yes post: no)
    parport_pc 00:09: activated
    parport_pc 00:09: reported by Plug and Play ACPI
    parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
    rtc_cmos 00:07: RTC can wake from S4
    rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one year, 114 bytes nvram
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    input: PC Speaker as /class/input/input5
    iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
    iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0xd860)
    iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    toshiba_acpi: Toshiba Laptop ACPI Extras version 0.19
    toshiba_acpi: HCI method: \_SB_.VALZ.GHCI
    yenta_cardbus 0000:01:0b.0: CardBus bridge found [1179:0001]
    yenta_cardbus 0000:01:0b.0: ISA IRQ mask 0x0c38, PCI irq 18
    yenta_cardbus 0000:01:0b.0: Socket status: 30000020
    yenta_cardbus 0000:01:0b.0: pcmcia: parent PCI bridge I/O window: 0xc000 - 0xcfff
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc000-0xcfff: clean.
    yenta_cardbus 0000:01:0b.0: pcmcia: parent PCI bridge Memory window: 0xcff00000 - 0xcfffffff
    yenta_cardbus 0000:01:0b.0: pcmcia: parent PCI bridge Memory window: 0x28000000 - 0x2bffffff
    Intel ICH Modem 0000:00:1f.6: power state changed by ACPI to D0
    Intel ICH Modem 0000:00:1f.6: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    Intel ICH Modem 0000:00:1f.6: setting latency timer to 64
    Intel ICH 0000:00:1f.5: power state changed by ACPI to D0
    Intel ICH 0000:00:1f.5: enabling device (0000 -> 0003)
    Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    Intel ICH 0000:00:1f.5: setting latency timer to 64
    input: PS/2 Mouse as /class/input/input6
    input: AlpsPS/2 ALPS GlidePoint as /class/input/input7
    pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
    pci 0000:02:00.0: reg 10 32bit mmio: [0x000000-0x00ffff]
    cfg80211: Using static regulatory domain info
    cfg80211: Regulatory domain: EU
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2482000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
    (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
    (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
    (5490000 KHz - 5710000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
    pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
    ath5k 0000:02:00.0: enabling device (0000 -> 0002)
    ath5k 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    ath5k 0000:02:00.0: registered as 'phy0'
    wmaster0 (ath5k): not using net_device_ops yet
    phy0: Selected rate control algorithm 'minstrel'
    wlan0 (ath5k): not using net_device_ops yet
    ath5k phy0: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43)
    ath5k phy0: RF2112B 2GHz radio found (0x46)
    udev: renamed network interface wlan0 to ath0
    intel8x0_measure_ac97_clock: measured 55358 usecs
    intel8x0: clocking to 48000
    EXT3 FS on dm-1, internal journal
    loop: module loaded
    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on dm-7, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on dm-5, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on dm-2, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on dm-3, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    Adding 1048568k swap on /dev/mapper/strider-swap_crypt. Priority:-1 extents:1 across:1048568k
    ADDRCONF(NETDEV_UP): ath0: link is not ready
    ath0: authenticate with AP 00:14:c1:38:e5:15
    ath0: authenticated
    ath0: associate with AP 00:14:c1:38:e5:15
    ath0: RX AssocResp from 00:14:c1:38:e5:15 (capab=0x411 status=0 aid=2)
    ath0: associated
    ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
    lp0: using parport0 (interrupt-driven).
    ppdev: user-space parallel port driver
    ADDRCONF(NETDEV_UP): eth0: link is not ready
    ADDRCONF(NETDEV_UP): eth0: link is not ready
    ath0: no IPv6 routers present
    CPU0 attaching NULL sched-domain.
    CPU0 attaching NULL sched-domain.
    \
     
     \ /
      Last update: 2009-03-04 21:19    [W:0.138 / U:121.600 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site