lkml.org 
[lkml]   [2009]   [Jan]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Subjectscheduler nice 19 versus 'idle' behavior / static low-priority scheduling
From
Date
All (though perhaps of special interest to a few such as Ingo, Peter,
and David),

I am posting regarding an issue I have been dealing with recently,
though this post is not really a request for troubleshooting. Instead
I'd like to ramble for just a moment about my understanding of the
current 2.6 scheduler, describe the behavior I'm seeing, and discuss a
couple of the architectural solutions I've considered, as well as pose
the question whether anyone else views this as a general-case problem
worthy of being addressed, or whether this is something that gets
ignored by and large. It is my hope that this is not too off-topic for
this group.

First, let me explain the issue I encountered. I am running a relatively
powerful system for a home desktop, an Intel Core 2 Quad Q9450 with 4 GB
of RAM. If it matters for the discussion, it also has 4 drives in an
mdraid raid-5 array, and decent I/O throughput. In normal circumstances
it is quite responsive as a desktop (kde 3.5.4 atm). It is further a
very carefully configured kernel build, including only those things
which I truly need, and excluding everything else. I often use it to
watch DVD movies, and have had no trouble with performance in general.

Recently I installed the Folding@Home client, which many of you may be
familiar with, intended to utilize spare CPU cycles to perform protein
folding simulations in order to further medical research. It is not a
multi-threaded client at this point, so it simply runs four instances on
my system, since it has four cores. It is configured to run at
nice-level 19.

Because it is heavily optimized, and needs little external data to
perform its work, it spends almost all of its time cpu-bound, with
little to no io-wait or blocking on network calls, etc. I had been
using it for about a week with no real difficulty until I went to watch
another DVD and found that the video was slightly stuttery/jerky so long
as foldingathome was running in the background. Once I shut it down,
the video playback resumed its normal smooth form.

There are a couple simple solutions to this:

Substantially boosting the process priority of the mplayer process also
returns the video to smooth playback, but this is undesirable in that it
requires manual intervention each time, and root privileges. It fails to
achieve what I want, which is for the foldingathome computation to not
interfere with anything else I may try to do. I want my compiles to be
as *exactly* as fast as they were without it as possible, etc.

Stopping foldingathome before I do something performance sensitive is
also possible, but again smacks of workaround rather than solution. The
scheduler should be able to resolve the goal without me stopping the
other work.

I have done a bit of research on how the kernel scheduler works, and why
I am seeing this behavior. I had previously, apparently ignorantly,
equated 'nice 19' with being akin to Microsoft Windows' 'idle' thread
priority, and assumed it would never steal CPU cycles from a process
with a higher(lower, depending on nomenclature) priority.

It is my current understanding that when mplayer is running (also
typically CPU bound, occassionally it becomes I/O bound briefly), one of
the instances of foldingathome, which is sharing the CPU (core) with
mplayer starts getting starved, and the scheduler dynamically rewards it
with up to four additional priority levels based on the time remaining
in its quantum which it was not allowed to execute for.

At this point, when mplayer blocks for just a moment, say to page in the
data for the next video frame, foldingathome gets scheduled again, and
gets to run for at least MIN_TIMESLICE (plus, due to the lack of kernel
pre-emptibility, possibly longer). It appears that it takes too long to
switch back to mplayer and the result is the stuttering picture I
observe.

I have tried adjusting CONFIG_HZ_xxx from 300 (where I had it) to 1000,
and noted some improvement, but not complete remedy.

In my prior searching on this, I found only one poster with the same
essential problem (from 2004, and regarding distributed.net in the
background, which is essentially the same problem). The only technical
answer given him was to perhaps try tuning the MIN_TIMESLICE value
downward. It is my understanding that this parameter is relatively
important in order to avoid cache thrashing, and I do not wish to alter
it and have not so far.

Given all of the above, I am unconvinced that I see a good overall
solution. However, one thing that seems to me a glaring weakness of the
scheduler is that only realtime priority threads can be given static
priorities. What I really want for foldingathome, and similar tasks, is
static, low priority. Something that would not boost up, no matter how
well behaved it was or how much it had been starved, or how close to the
same memory segments the needed code was.

I think that there are probably (at least) three approaches here. One I
consider unnacceptable at the outset, which is to alter the semantics of
nice 19 such that it does not boost. Since this would break existing
assumptions and code, I do not think it is feasible.

Secondly, one could add additional nice levels which would correspond to
new static priorities below the bottom of the current user ones. This
should not interfere with the O(1) scheduler implementation as I
understand it, because current I believe 5 32-bit words are used to flag
the queue usage, and 140 priorities leaves 20 more bits available for
new priorities. This has its own problems however, in that existing
tools which examine process priorities could break on priorities outside
the known 'nice' range of -20 to 19.

Finally, new scheduling classes could be introduced, together with new
system calls so that applications could select a different scheduling
class at startup. In this way, applications could volunteer to use a
scheduling class which never received dynamic 'reward' boosts that would
raise their priorities. I believe Solaris has done this since Solaris
9, with the 'FX' scheduling class.

Stepping back:

1) Is my problem 'expected' based on others' understanding of the
current design of the scheduler, or do I have a one-off problem to
troubleshoot here?

2) Am I overlooking obvious alternative (but clean) fixes?

3) Does anyone else see the need for static, but low process priorities?

4) What is the view of introducing a new scheduler class to handle this?

I welcome any further feedback on this. I will try to follow replies
on-list, but would appreciate being CC'd off-list as well. Please make
the obvious substitution to my email address in order to bypass the
spam-killer.

Thanks,
Nathanael Hoyle




\
 
 \ /
  Last update: 2009-01-30 06:53    [W:0.155 / U:0.136 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site