Messages in this thread | | | Date | Fri, 22 Feb 2008 15:08:30 +0100 (CET) | From | Unknown <> | Subject | PROBLEM: 2.4.36.1 hangs. |
| |
1) 2.4.36.1 hangs (probably during ext2_readdir())
2) 2.4.36.1 hangs during compilation of lighttpd-1.4.18. It is probably during ext2_readdir() but I cannot confirm that.. Currently it only happens during compilation of lighttpd-1.4.18, always in the same place. Kernel 2.4.36 w/ same options (make oldconfig) works fine.
Last few lines of 'strace -f make' just before hang: [pid 12817] open(".", O_RDONLY|O_NONBLOCK|O_LARGEFILE|O_DIRECTORY) = 3 [pid 12817] fstat64(3, {st_mode=S_IFDIR|0777, st_size=8192, ...}) = 0 [pid 12817] fcntl64(3, F_SETFD, FD_CLOEXEC) = 0 [pid 12817] getdents64(3, /* 114 entries */, 4096) = 4088 [pid 12817] getdents64(3, /* 63 entries */, 4096) = 2424 [pid 12817] getdents64(3,
3) ext2fs
4) None.
5) None. Kernel just hangs.
6) cd /home/root/src/lighttpd-1.4.18 N=lighttpd AP="/usr/local/$N" EP="/usr/local" ETC="/etc/$N" ./configure --prefix=$AP --bindir=$EP/bin --sbindir=$EP/sbin \ --libexecdir=$EP/libexec --mandir=$EP/man --sysconfdir=$ETC --disable-ipv6 make
7.1) Slackware-11.0 Linux darkstar 2.4.36.1 #2 Fri Feb 22 14:13:50 CET 2008 i686 pentium3 i386 GNU/Linux
Gnu C 3.4.6 Gnu make 3.81 binutils 2.15.92.0.2 util-linux 2.12r mount 2.12r modutils 2.4.27 e2fsprogs 1.38 Linux C Library 2.3.6 Dynamic linker (ldd) 2.3.6 Procps 3.2.7 Net-tools 1.60 Kbd 74: Sh-utils 5.97 Modules Loaded
7.2) processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 8 model name : Pentium III (Coppermine) stepping : 10 cpu MHz : 930.329 cache size : 256 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr sse bogomips : 1854.66
7.3) None 7.4) # cat /proc/ioports: 0000-001f : dma1 0020-003f : pic1 0040-0043 : timer0 0050-0053 : timer1 0060-006f : keyboard 0080-008f : dma page reg 00a0-00bf : pic2 00c0-00df : dma2 00f0-00ff : fpu 01f0-01f7 : ide0 03c0-03df : vga+ 03f6-03f6 : ide0 03f8-03ff : serial(auto) 0cf8-0cff : PCI conf1 1000-100f : Intel Corp. 82801AA IDE 1000-1007 : ide0 1008-100f : ide1 1400-141f : Intel Corp. 82801AA USB 1800-180f : Intel Corp. 82801AA SMBus 2400-243f : Intel Corp. 82557/8/9 [Ethernet Pro 100] 2400-243f : eepro100 f000-f07f : motherboard f000-f003 : PM1a_EVT_BLK f004-f005 : PM1a_CNT_BLK f008-f00b : PM_TMR f028-f02b : GPE0_BLK f02c-f02f : GPE1_BLK f100-f10f : motherboard f180-f1bf : motherboard f800-f81f : motherboard f820-f82f : motherboard fe00-fe00 : motherboard
# cat /proc/iomem 00000000-0009ebff : System RAM 0009ec00-0009ffff : reserved 000a0000-000bffff : Video RAM area 000c0000-000c7fff : Video ROM 000c8000-000c97ff : Extension ROM 000f0000-000fffff : System ROM 00100000-1feeffff : System RAM 00100000-0027773b : Kernel code 0027773c-002c52e3 : Kernel data 1fef0000-1fefefff : ACPI Tables 1feff000-1fefffff : ACPI Non-volatile Storage 1ff00000-1fffffff : reserved f4000000-f407ffff : Intel Corp. 82810E DC-133 CGC [Chipset Graphics Controller] f4100000-f411ffff : Intel Corp. 82557/8/9 [Ethernet Pro 100] f4120000-f4120fff : Intel Corp. 82557/8/9 [Ethernet Pro 100] f4120000-f4120fff : eepro100 f8000000-fbffffff : Intel Corp. 82810E DC-133 CGC [Chipset Graphics Controller] ffb80000-ffbfffff : reserved fff00000-ffffffff : reserved
7.5) # lspci 00:00.0 Host bridge: Intel Corporation 82810E DC-133 GMCH [Graphics Memory Controller Hub] (rev 03) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0
00:01.0 VGA compatible controller: Intel Corporation 82810E DC-133 CGC [Chipset Graphics Controller] (rev 03) (prog-if 00 [VGA]) Subsystem: Siemens Nixdorf AG Unknown device 004a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M] Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=512K] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 PCI bridge: Intel Corporation 82801AA PCI Bridge (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 00002000-00002fff Memory behind bridge: f4100000-f41fffff Prefetchable memory behind bridge: fff00000-000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801AA ISA Bridge (LPC) (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801AA IDE (rev 02) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801AA IDE Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 4: I/O ports at 1000 [size=16]
00:1f.2 USB Controller: Intel Corporation 82801AA USB (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801AA USB Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin D routed to IRQ 9 Region 4: I/O ports at 1400 [size=32]
00:1f.3 SMBus: Intel Corporation 82801AA SMBus (rev 02) Subsystem: Intel Corporation 82801AA SMBus Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 5 Region 4: I/O ports at 1800 [size=16]
01:08.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 09) Subsystem: Siemens Nixdorf AG Unknown device 004b Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 9 Region 0: Memory at f4120000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 2400 [size=64] Region 2: Memory at f4100000 (32-bit, non-prefetchable) [size=128K] Expansion ROM at <unassigned> [disabled] [size=1M] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
7.6) None
7.7) Box has been tested via memtest86+ 15 hrs of test running, no errors
| |