Messages in this thread | | | Date | Sun, 10 Feb 2008 11:07:57 +0100 | From | Olaf Hering <> | Subject | pci_proc_init: proc_dir_entry '00' already registered |
| |
Current Linus tree gives this new warning during bootup:
+proc_dir_entry '00' already registered +Call Trace: +[c00000007b0dfba0] [c00000000000e4b0] .show_stack+0x70/0x1bc (unreliable) +[c00000007b0dfc50] [c0000000000f2714] .proc_register+0x130/0x210 +[c00000007b0dfd00] [c0000000000f299c] .proc_mkdir_mode+0x40/0x70 +[c00000007b0dfd80] [c000000000276ed8] .pci_proc_attach_device+0xac/0x144 +[c00000007b0dfe20] [c0000000005bdb3c] .pci_proc_init+0x74/0xac +[c00000007b0dfea0] [c0000000005a27ac] .kernel_init+0x1d0/0x394 +[c00000007b0dff90] [c00000000001e258] .kernel_thread+0x4c/0x68
Its a dualcore G5.
DART table allocated at: c00000007f000000 Using PowerMac machine description Page orders: linear mapping = 24, virtual = 12, io = 12 Found initrd at 0xc000000001300000:0xc000000001559c00 Found U4 memory controller & host bridge @ 0xf8000000 revision: 0x42 Mapped at 0xd000080080000000 Found a Shasta mac-io controller, rev: 0, mapped at 0xd000080080041000 PowerMac motherboard: PowerMac G5 Dual Core DART IOMMU initialized for U4 type chipset console [udbg0] enabled CPU maps initialized for 1 thread per core (thread shift is 0) Starting Linux PPC64 #221 SMP Sun Feb 10 10:50:00 CET 2008 ----------------------------------------------------- ppc64_pft_size = 0x0 physicalMemorySize = 0x80000000 htab_address = 0xc00000007c000000 htab_hash_mask = 0x3ffff ----------------------------------------------------- Linux version 2.6.24-g5-00000-g25f6663 (olaf@g5) (gcc version 4.1.0 (SUSE Linux)) #221 SMP Sun Feb 10 10:50:00 CET 2008 [boot]0012 Setup Arch Entering add_active_range(0, 0, 524288) 0 entries of 256 used Found U4-PCIE PCI host bridge. Firmware bus number: 0->255 PCI host bridge /pci@0,f0000000 ranges: MEM 0x00000000f1000000..0x00000000f1ffffff -> 0x00000000f1000000 IO 0x00000000f0000000..0x00000000f07fffff -> 0x0000000000000000 MEM 0x0000000090000000..0x00000000afffffff -> 0x0000000090000000 Can't get bus-range for /ht@0,f2000000, assume bus 0 Found U3-HT PCI host bridge. Firmware bus number: 0->239 PCI host bridge /ht@0,f2000000 (primary) ranges: SMU: Driver 0.7 (c) 2005 Benjamin Herrenschmidt, IBM Corp. nvram: Checking bank 0... nvram: gen0=208, gen1=209 nvram: Active bank is: 1 nvram: OF partition at 0x410 nvram: XP partition at 0x1020 nvram: NR partition at 0x1120 Top of RAM: 0x80000000, Total RAM: 0x80000000 Memory hole size: 0MB Zone PFN ranges: DMA 0 -> 524288 Normal 524288 -> 524288 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 524288 On node 0 totalpages: 524288 DMA zone: 7168 pages used for memmap DMA zone: 0 pages reserved DMA zone: 517120 pages, LIFO batch:31 Normal zone: 0 pages used for memmap Movable zone: 0 pages used for memmap [boot]0015 Setup Done Built 1 zonelists in Zone order, mobility grouping on. Total pages: 517120 Kernel command line: root=UUID=a77c3a2a-dd4a-4cf6-8c74-287c49897b10 sysrq=1 quiet video=nvidiafb:1024x768@85,bpp:16 panic=12 mpic: Setting up MPIC " MPIC 1 " version 1.2 at f8040000, max 4 CPUs mpic: ISU size: 124, shift: 7, mask: 7f mpic: Initializing for 124 sources mpic: Setting up HT PICs workarounds for U3/U4 mpic: - HT:07.0 [0x90] vendor 106b device 0053 has 86 irqs PID hash table entries: 4096 (order: 12, 32768 bytes) time_init: decrementer frequency = 33.333333 MHz time_init: processor frequency = 2300.000000 MHz clocksource: timebase mult[7800001] shift[22] registered clockevent: decrementer mult[888] shift[16] cpu[0] Console: colour dummy device 80x25 console handover: boot [udbg0] -> real [tty0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Memory: 2005248k/2097152k available (5984k kernel code, 91208k reserved, 940k data, 489k bss, 216k init) Calibrating delay loop... 66.56 BogoMIPS (lpj=332800) Mount-cache hash table entries: 256 device-tree: Duplicate name in /ht@0,f2000000/pci@8/mac-io@7/i2c@18000, renamed to "i2c-bus@0#1" PowerMac SMP probe found 2 cpus KeyWest i2c @0xf8001003 irq 16 /u4@0,f8000000/i2c@f8001000 channel 1 bus /u4@0,f8000000/i2c@f8001000/i2c-bus@1 KeyWest i2c @0x80018000 irq 27 /ht@0,f2000000/pci@8/mac-io@7/i2c@18000 channel 0 bus /ht@0,f2000000/pci@8/mac-io@7/i2c@18000/i2c-bus@0 channel 0 bus /ht@0,f2000000/pci@8/mac-io@7/i2c@18000/i2c-bus@0 SMU i2c /smu@0,0/smu-i2c-control@0 channel b bus /smu@0,0/smu-i2c-control@0/i2c-bus@b channel e bus /smu@0,0/smu-i2c-control@0/i2c-bus@e Processor timebase sync using platform function mpic: requesting IPIs ... Processor 1 found. clockevent: decrementer mult[888] shift[16] cpu[1] Brought up 2 CPUs net_namespace: 304 bytes NET: Registered protocol family 16 PCI: Probing PCI hardware IOMMU table initialized, virtual merging enabled PCI: Closing bogus Apple Firmware region 2 on bus 0x0a PCI: Closing bogus Apple Firmware region 2 on bus 0x02 PCI: Closing bogus Apple Firmware region 2 on bus 0x01 PCI: Closing bogus Apple Firmware region 2 on bus 0x03 PCI: Cannot allocate resource region 0 of device 0000:0a:00.0, will remap PCI: Cannot allocate resource region 1 of device 0000:0a:00.0, will remap PCI: Cannot allocate resource region 3 of device 0000:0a:00.0, will remap PCI: Bridge: 0000:00:0b.0 IO window: 0000-ffff MEM window: 0xa8000000-0xa9ffffff PREFETCH window: 0x0000000090000000-0x00000000a7ffffff PCI: Bridge: 0001:00:01.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0001:00:02.0 IO window: disabled. MEM window: 0xfa500000-0xfa5fffff PREFETCH window: disabled. PCI: Bridge: 0001:00:03.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0001:00:04.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0001:00:05.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0001:00:06.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0001:00:07.0 IO window: disabled. MEM window: 0xfa000000-0xfa3fffff PREFETCH window: disabled. PCI: Bridge: 0001:00:08.0 IO window: disabled. MEM window: 0x80000000-0x800fffff PREFETCH window: disabled. PCI: Bridge: 0001:00:09.0 IO window: disabled. MEM window: 0xfa400000-0xfa4fffff PREFETCH window: disabled. PCI: Probing PCI hardware done Registering pmac pic with sysfs... SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 Time: timebase clocksource has been installed. Switched to high resolution mode on CPU 0 Switched to high resolution mode on CPU 1 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered Unpacking initramfs... done Freeing initrd memory: 2407k freed nvram_init: Could not find nvram partition for nvram buffered error logging. Registering G5 CPU frequency driver Frequency method: SCOM, Voltage method: GPIO Low: 1150 Mhz, High: 2300 Mhz, Cur: 2300 MHz Installing knfsd (copyright (C) 1996 okir@monad.swb.de). SGI XFS with large block/inode numbers, no debug enabled io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) proc_dir_entry '00' already registered Call Trace: [c00000007b0dfba0] [c00000000000e4b0] .show_stack+0x70/0x1bc (unreliable) [c00000007b0dfc50] [c0000000000f2714] .proc_register+0x130/0x210 [c00000007b0dfd00] [c0000000000f299c] .proc_mkdir_mode+0x40/0x70 [c00000007b0dfd80] [c000000000276ed8] .pci_proc_attach_device+0xac/0x144 [c00000007b0dfe20] [c0000000005bdb3c] .pci_proc_init+0x74/0xac [c00000007b0dfea0] [c0000000005a27ac] .kernel_init+0x1d0/0x394 [c00000007b0dff90] [c00000000001e258] .kernel_thread+0x4c/0x68 nvidiafb: Device ID: 10de0141 nvidiafb: CRTC0 analog found nvidiafb: CRTC1 analog found i2c-adapter i2c-0: unable to read EDID block. i2c-adapter i2c-0: unable to read EDID block. i2c-adapter i2c-0: unable to read EDID block. nvidiafb: Found OF EDID for head 1 nvidiafb: EDID found from BUS1 nvidiafb: EDID found from BUS2 nvidiafb: CRTC 0 appears to have a CRT attached nvidiafb: Using CRT on CRTC 0 Console: switching to colour frame buffer device 128x48 nvidiafb: PCI nVidia NV14 framebuffer (64MB @ 0x90000000) Generic RTC Driver v1.07 loop: module loaded tg3.c:v3.87 (December 20, 2007) eth0: Tigon3 [partno(BCM95780) rev 8003 PHY(5780)] (PCIX:133MHz:64-bit) 10/100/1000Base-T Ethernet 00:14:51:68:b7:00 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1] eth0: dma_rwctrl[76144000] dma_mask[40-bit] eth1: Tigon3 [partno(BCM95780) rev 8003 PHY(5780)] (PCIX:133MHz:64-bit) 10/100/1000Base-T Ethernet 00:14:51:68:b7:01 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1] eth1: dma_rwctrl[76144000] dma_mask[40-bit] usbcore: registered new interface driver asix Linux video capture interface: v2.00 usbcore: registered new interface driver zr364xx /home/olaf/kernel/linux-2.6/drivers/media/video/zr364xx.c: Zoran 364xx module loaded MacIO PCI driver attached to Shasta chipset windfarm: initializing for dual-core desktop G5 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PCI: Enabling device 0001:03:0d.0 (0004 -> 0006) ide0: Found Apple Shasta ATA-6 controller, bus ID 3, irq 38 Probing IDE interface ide0... hda: HL-DT-ST DVD-RW GWA-4165B, ATAPI CD/DVD-ROM drive hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 hda: UDMA/66 mode selected ide0 at 0xd0000800822fa000-0xd0000800822fa007,0xd0000800822fa160 on irq 38 hda: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods sata_svw 0001:03:0c.0: version 2.3 scsi0 : sata_svw scsi1 : sata_svw scsi2 : sata_svw scsi3 : sata_svw ata1: SATA max UDMA/133 mmio m8192@0xfa402000 port 0xfa402000 irq 18 ata2: SATA max UDMA/133 mmio m8192@0xfa402000 port 0xfa402100 irq 18 ata3: SATA max UDMA/133 mmio m8192@0xfa402000 port 0xfa402200 irq 18 ata4: SATA max UDMA/133 mmio m8192@0xfa402000 port 0xfa402300 irq 18 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7: WDC WD2500JS-41MVB1, 10.02E01, max UDMA/133 ata1.00: 488397168 sectors, multi 0: LBA48 ata1.00: configured for UDMA/133 ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata2.00: ATA-7: Maxtor 6V250F0, VA111630, max UDMA/133 ata2.00: 490234752 sectors, multi 16: LBA48 NCQ (depth 0/32) ata2.00: configured for UDMA/133 ata3: SATA link down (SStatus 0 SControl 0) ata4: SATA link down (SStatus 0 SControl 0) scsi 0:0:0:0: Direct-Access ATA WDC WD2500JS-41M 10.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6 sda7 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 1:0:0:0: Direct-Access ATA Maxtor 6V250F0 VA11 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 490234752 512-byte hardware sectors (251000 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sdb] 490234752 512-byte hardware sectors (251000 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: [mac] sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 sdb11 sdb12 sd 1:0:0:0: [sdb] Attached SCSI disk sd 1:0:0:0: Attached scsi generic sg1 type 0 PCI: Enabling device 0001:03:0e.0 (0000 -> 0002) firewire_ohci: Added fw-ohci device 0001:03:0e.0, OHCI version 1.0 video1394: Installed video1394 module ieee1394: raw1394: /dev/raw1394 device initialized PCI: Enabling device 0001:01:0b.2 (0004 -> 0006) ehci_hcd 0001:01:0b.2: EHCI Host Controller ehci_hcd 0001:01:0b.2: new USB bus registered, assigned bus number 1 ehci_hcd 0001:01:0b.2: irq 70, io mem 0x80080000 ehci_hcd 0001:01:0b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 5 ports detected usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.24-g5-00000-g25f6663 ehci_hcd usb usb1: SerialNumber: 0001:01:0b.2 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0001:01:0b.0 (0000 -> 0002) ohci_hcd 0001:01:0b.0: OHCI Host Controller ohci_hcd 0001:01:0b.0: new USB bus registered, assigned bus number 2 ohci_hcd 0001:01:0b.0: irq 70, io mem 0x80082000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.24-g5-00000-g25f6663 ohci_hcd usb usb2: SerialNumber: 0001:01:0b.0 PCI: Enabling device 0001:01:0b.1 (0000 -> 0002) ohci_hcd 0001:01:0b.1: OHCI Host Controller ohci_hcd 0001:01:0b.1: new USB bus registered, assigned bus number 3 ohci_hcd 0001:01:0b.1: irq 70, io mem 0x80081000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected firewire_core: created new fw device fw0 (0 config rom retries, S800) firewire_core: phy config: card 0, new root=ffc1, gap_count=5 usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: OHCI Host Controller usb usb3: Manufacturer: Linux 2.6.24-g5-00000-g25f6663 ohci_hcd usb usb3: SerialNumber: 0001:01:0b.1 usb 2-1: new full speed USB device using ohci_hcd and address 2 usb 2-1: configuration #1 chosen from 2 choices usb 2-1: New USB device found, idVendor=06cd, idProduct=0110 usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-1: Product: Keyspan USB Serial Adapter usb 2-1: Manufacturer: Keyspan, a division of InnoSys Inc. usb 3-2: new full speed USB device using ohci_hcd and address 2 usb 3-2: configuration #1 chosen from 1 choice hub 3-2:1.0: USB hub found hub 3-2:1.0: 3 ports detected usb 3-2: New USB device found, idVendor=05ac, idProduct=1003 usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 3-2: Product: Hub in Apple Extended USB Keyboard usb 3-2: Manufacturer: Mitsumi Electric usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usb 3-2.1: new low speed USB device using ohci_hcd and address 3 usb 3-2.1: configuration #1 chosen from 1 choice usb 3-2.1: New USB device found, idVendor=05ac, idProduct=0304 usb 3-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 3-2.1: Product: Apple Optical USB Mouse usb 3-2.1: Manufacturer: Mitsumi Electric usb 3-2.3: new full speed USB device using ohci_hcd and address 4 usb 3-2.3: configuration #1 chosen from 1 choice usb 3-2.3: New USB device found, idVendor=05ac, idProduct=020b usb 3-2.3: New USB device strings: Mfr=1, Product=3, SerialNumber=0 usb 3-2.3: Product: Apple Extended USB Keyboard usb 3-2.3: Manufacturer: Mitsumi Electric usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver libusual usbcore: registered new interface driver usbserial /home/olaf/kernel/linux-2.6/drivers/usb/serial/usb-serial.c: USB Serial Driver core /home/olaf/kernel/linux-2.6/drivers/usb/serial/usb-serial.c: USB Serial support registered for Keyspan - (without firmware) /home/olaf/kernel/linux-2.6/drivers/usb/serial/usb-serial.c: USB Serial support registered for Keyspan 1 port adapter /home/olaf/kernel/linux-2.6/drivers/usb/serial/usb-serial.c: USB Serial support registered for Keyspan 2 port adapter /home/olaf/kernel/linux-2.6/drivers/usb/serial/usb-serial.c: USB Serial support registered for Keyspan 4 port adapter keyspan 2-1:1.0: Keyspan 2 port adapter converter detected usb 2-1: Keyspan 2 port adapter converter now attached to ttyUSB0 usb 2-1: Keyspan 2 port adapter converter now attached to ttyUSB1 usbcore: registered new interface driver keyspan /home/olaf/kernel/linux-2.6/drivers/usb/serial/keyspan.c: v1.1.5:Keyspan USB to Serial Converter Driver mice: PS/2 mouse device common for all mice PowerMac i2c bus smu 14 registered wf_sat: creating sat at address b0 PowerMac i2c bus smu 11 registered PowerMac i2c bus mac-io 0 registered PowerMac i2c bus mac-io 0 registered found max6690, loc=BACKSIDE addr=0x98 found max6690, loc=TUNNEL addr=0x9c PowerMac i2c bus u4 1 registered usbcore: registered new interface driver hiddev input: Mitsumi Electric Apple Optical USB Mouse as /class/input/input0 input: USB HID v1.10 Mouse [Mitsumi Electric Apple Optical USB Mouse] on usb-0001:01:0b.1-2.1 input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input1 input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:01:0b.1-2.3 input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input2 input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:01:0b.1-2.3 usbcore: registered new interface driver usbhid /home/olaf/kernel/linux-2.6/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.16rc2 (Thu Jan 31 16:40:16 2008 UTC). usbcore: registered new interface driver snd-usb-audio usbcore: registered new interface driver snd-usb-usx2y snd-aoa-fabric-layout: found bus with layout 68 snd-aoa-fabric-layout: Using PMF GPIOs snd-aoa-codec-onyx: found pcm3052 snd-aoa-fabric-layout: platform-onyx-codec-ref doesn't match! snd-aoa: fabric didn't like codec onyx snd-aoa-codec-onyx: found pcm3052 snd-aoa-fabric-layout: can use this codec snd-aoa-codec-onyx: attached to onyx codec via i2c snd-aoa-codec-onyx: created and attached onyx instance ALSA device list: #0: SoundByLayout TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. Freeing unused kernel memory: 216k freed ioctl32(showconsole:476): Unknown cmd fd(0) cmd(40045432){t:'T';sz:4} arg(ffcd8bb8) on /dev/console ioctl32(showconsole:479): Unknown cmd fd(0) cmd(40045432){t:'T';sz:4} arg(ffdafbb8) on /dev/console windfarm: CPUs control loops started. sat 0 partition c8: c8 6 2 7f ff 2 ff 1 fb bf 0 41 0 20 0 0 0 7 89 37 0 a0 0 0 ioctl32(showconsole:838): Unknown cmd fd(0) cmd(40045432){t:'T';sz:4} arg(ffefbbb8) on /dev/console sat 0 partition c4: c4 4 1 7f 22 11 e0 e6 ff 55 7b 12 ec 11 0 0 ioctl32(showconsole:870): Unknown cmd fd(0) cmd(40045432){t:'T';sz:4} arg(ffc87b18) on /dev/console Adding 1048568k swap on /dev/sdb3. Priority:-1 extents:1 across:1048568k ioctl32(showconsole:897): Unknown cmd fd(0) cmd(40045432){t:'T';sz:4} arg(ffb73aa8) on /dev/console (deleted) sat 0 partition c9: c9 6 2 7f ff 2 ff 1 fb bf 0 41 0 20 0 0 0 7 89 37 0 a0 0 0 sat 0 partition c5: c5 4 1 7f 22 11 e0 e6 ff 55 7b 12 ec 11 0 0 windfarm: Backside control loop started. windfarm: Slots control loop started. windfarm: Drive bay control loop started. ioctl32(showconsole:1781): Unknown cmd fd(0) cmd(40045432){t:'T';sz:4} arg(ffbf2aa8) on /dev/console (deleted) XFS mounting filesystem sdb11 Ending clean XFS mount for filesystem: sdb11 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. ioctl32(showconsole:1953): Unknown cmd fd(0) cmd(40045432){t:'T';sz:4} arg(ff976ab8) on /dev/console (deleted) ioctl32(showconsole:2058): Unknown cmd fd(0) cmd(40045432){t:'T';sz:4} arg(ffa39af8) on /dev/console tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is on for TX and on for RX. ioctl32(showconsole:2641): Unknown cmd fd(0) cmd(40045432){t:'T';sz:4} arg(fff16a88) on /dev/tty0 ioctl32(showconsole:3052): Unknown cmd fd(0) cmd(40045432){t:'T';sz:4} arg(ffedaac8) on /dev/tty0
| |