lkml.org 
[lkml]   [2007]   [Aug]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/2] Replace CONFIG_USB_OHCI with CONFIG_USB_OHCI_HCD in a few overlooked files
Date
Finish the rename of CONFIG_USB_OHCI to CONFIG_USB_OHCI_HCD, which started
in 2005 (before 2.6.12-rc2). The patch in this message has not been applied yet;
moreover, it is not something to fix afterwards. I've verified that no more
instances of 'CONFIG_USB_[UOE]HCI\>' exist in the source tree.

http://www.linux-mips.org/archives/linux-mips/2005-06/msg00060.html

I'm also sending a script to detect undefined Kconfig variables in next patch.

Thanks to my colleague Giuseppe Patanè for the original report: he discovered
the original mail (above) and for verified that the fix had not yet been
applied.

Cc: Giuseppe Patanè <giuseppe.patane@tvblob.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
---

arch/mips/au1000/mtx-1/board_setup.c | 4 ++--
arch/mips/au1000/pb1000/board_setup.c | 6 +++---
arch/mips/au1000/pb1100/board_setup.c | 4 ++--
arch/mips/au1000/pb1500/board_setup.c | 6 +++---
4 files changed, 10 insertions(+), 10 deletions(-)

diff --git a/arch/mips/au1000/mtx-1/board_setup.c b/arch/mips/au1000/mtx-1/board_setup.c
index 7bc5af8..1688ca9 100644
--- a/arch/mips/au1000/mtx-1/board_setup.c
+++ b/arch/mips/au1000/mtx-1/board_setup.c
@@ -54,11 +54,11 @@ void board_reset (void)

void __init board_setup(void)
{
-#ifdef CONFIG_USB_OHCI
+#ifdef CONFIG_USB_OHCI_HCD
// enable USB power switch
au_writel( au_readl(GPIO2_DIR) | 0x10, GPIO2_DIR );
au_writel( 0x100000, GPIO2_OUTPUT );
-#endif // defined (CONFIG_USB_OHCI)
+#endif // defined (CONFIG_USB_OHCI_HCD)

#ifdef CONFIG_PCI
#if defined(__MIPSEB__)
diff --git a/arch/mips/au1000/pb1000/board_setup.c b/arch/mips/au1000/pb1000/board_setup.c
index 824cfaf..f25b38f 100644
--- a/arch/mips/au1000/pb1000/board_setup.c
+++ b/arch/mips/au1000/pb1000/board_setup.c
@@ -54,7 +54,7 @@ void __init board_setup(void)
au_writel(0, SYS_PINSTATERD);
udelay(100);

-#ifdef CONFIG_USB_OHCI
+#ifdef CONFIG_USB_OHCI_HCD
/* zero and disable FREQ2 */
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0xFFF00000;
@@ -102,7 +102,7 @@ void __init board_setup(void)
/*
* Route 48MHz FREQ2 into USB Host and/or Device
*/
-#ifdef CONFIG_USB_OHCI
+#ifdef CONFIG_USB_OHCI_HCD
sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
#endif
au_writel(sys_clksrc, SYS_CLKSRC);
@@ -116,7 +116,7 @@ void __init board_setup(void)
au_writel(pin_func, SYS_PINFUNC);
au_writel(0x2800, SYS_TRIOUTCLR);
au_writel(0x0030, SYS_OUTPUTCLR);
-#endif // defined (CONFIG_USB_OHCI)
+#endif // defined (CONFIG_USB_OHCI_HCD)

// make gpio 15 an input (for interrupt line)
pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x100);
diff --git a/arch/mips/au1000/pb1100/board_setup.c b/arch/mips/au1000/pb1100/board_setup.c
index 6bc1f8e..3205f88 100644
--- a/arch/mips/au1000/pb1100/board_setup.c
+++ b/arch/mips/au1000/pb1100/board_setup.c
@@ -54,7 +54,7 @@ void __init board_setup(void)
au_writel(0, SYS_PININPUTEN);
udelay(100);

-#ifdef CONFIG_USB_OHCI
+#ifdef CONFIG_USB_OHCI_HCD
{
u32 pin_func, sys_freqctrl, sys_clksrc;

@@ -98,7 +98,7 @@ void __init board_setup(void)
pin_func |= 0x8000;
au_writel(pin_func, SYS_PINFUNC);
}
-#endif // defined (CONFIG_USB_OHCI)
+#endif // defined (CONFIG_USB_OHCI_HCD)

/* Enable sys bus clock divider when IDLE state or no bus activity. */
au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
diff --git a/arch/mips/au1000/pb1500/board_setup.c b/arch/mips/au1000/pb1500/board_setup.c
index c9b6556..118e32a 100644
--- a/arch/mips/au1000/pb1500/board_setup.c
+++ b/arch/mips/au1000/pb1500/board_setup.c
@@ -56,7 +56,7 @@ void __init board_setup(void)
au_writel(0, SYS_PINSTATERD);
udelay(100);

-#ifdef CONFIG_USB_OHCI
+#ifdef CONFIG_USB_OHCI_HCD

/* GPIO201 is input for PCMCIA card detect */
/* GPIO203 is input for PCMCIA interrupt request */
@@ -85,7 +85,7 @@ void __init board_setup(void)
/*
* Route 48MHz FREQ2 into USB Host and/or Device
*/
-#ifdef CONFIG_USB_OHCI
+#ifdef CONFIG_USB_OHCI_HCD
sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
#endif
au_writel(sys_clksrc, SYS_CLKSRC);
@@ -95,7 +95,7 @@ void __init board_setup(void)
// 2nd USB port is USB host
pin_func |= 0x8000;
au_writel(pin_func, SYS_PINFUNC);
-#endif // defined (CONFIG_USB_OHCI)
+#endif // defined (CONFIG_USB_OHCI_HCD)



-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2007-08-24 16:41    [W:0.046 / U:0.388 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site