lkml.org 
[lkml]   [2004]   [Mar]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: 2.6.5-rc3-mm1
From
Date
Hello Andrew,

This shows up on NForce2 board.

Linux version 2.6.5-rc3-mm1 (root@blaze) (gcc version 3.3.3) #1 Tue Mar
30 14:40:20 EST 2004

from dmesg:

ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
mapped 4G/4G trampoline to fffeb000.
Initializing CPU#0
Kernel command line: auto BOOT_IMAGE=Slackware_2.6 ro root=801
rootflags=quota video=vesafb:ywrap,mtrr
CPU 0 irqstacks, hard=02443000 soft=02442000
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 2205.498 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Memory: 1035716k/1048512k available (2316k kernel code, 12052k reserved,
810k data, 180k init, 0k highmem)
Calibrating delay loop... 4358.14 BogoMIPS
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (ungzip failed); looks like an
initrd
Freeing initrd memory: 78k freed
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 3200+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22,
2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ... failed.
...trying to set up timer as Virtual Wire IRQ... failed.
...trying to set up timer as ExtINT IRQ... works.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2204.0623 MHz.
..... host bus clock speed is 400.0840 MHz.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfaee0, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs *16)
ACPI: PCI Interrupt Link [APC2] (IRQs *17)
ACPI: PCI Interrupt Link [APC3] (IRQs *18)
ACPI: PCI Interrupt Link [APC4] (IRQs *19)
ACPI: PCI Interrupt Link [APC5] (IRQs 16)
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCS] (IRQs *23)
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22)
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22)
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt Link [APCS] enabled at IRQ 23
IOAPIC[0]: Set PCI routing entry (2-23 -> 0xa9 -> IRQ 23 Mode:1
Active:0)
00:00:01[A] -> 2-23 -> IRQ 23
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
IOAPIC[0]: Set PCI routing entry (2-20 -> 0xb1 -> IRQ 20 Mode:1
Active:0)
00:00:02[A] -> 2-20 -> IRQ 20
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 22
IOAPIC[0]: Set PCI routing entry (2-22 -> 0xb9 -> IRQ 22 Mode:1
Active:0)
00:00:02[B] -> 2-22 -> IRQ 22
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
IOAPIC[0]: Set PCI routing entry (2-21 -> 0xc1 -> IRQ 21 Mode:1
Active:0)
00:00:02[C] -> 2-21 -> IRQ 21
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 20
ACPI: PCI Interrupt Link [APCI] enabled at IRQ 22
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21
ACPI: PCI Interrupt Link [APCK] enabled at IRQ 20
ACPI: PCI Interrupt Link [APCM] enabled at IRQ 22
ACPI: PCI Interrupt Link [APCZ] enabled at IRQ 21
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xc9 -> IRQ 18 Mode:1
Active:0)
00:01:06[A] -> 2-18 -> IRQ 18
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xd1 -> IRQ 19 Mode:1
Active:0)
00:01:06[B] -> 2-19 -> IRQ 19
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xd9 -> IRQ 16 Mode:1
Active:0)
00:01:06[C] -> 2-16 -> IRQ 16
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xe1 -> IRQ 17 Mode:1
Active:0)
00:01:06[D] -> 2-17 -> IRQ 17
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 000 00 1 0 0 0 0 0 0 00
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 1 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 0 0 1 1 D9
11 001 01 1 1 0 0 0 1 1 E1
12 001 01 1 1 0 0 0 1 1 C9
13 001 01 1 1 0 0 0 1 1 D1
14 001 01 1 1 0 0 0 1 1 B1
15 001 01 1 1 0 0 0 1 1 C1
16 001 01 1 1 0 0 0 1 1 B9
17 001 01 1 1 0 0 0 1 1 A9
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even
'acpi=off'
vesafb: framebuffer at 0xc0000000, mapped to 0x42808000, size 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:581c
vesafb: pmi: set display start = 020c58b0, set palette = 020c58fc
vesafb: pmi: ports = c010 c016 c054 c038 c03c c05c c000 c004 c0b0 c0b2
c0b4
vesafb: scrolling: ywrap using protected mode interface,
yres_virtual=8192
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
Machine check exception polling timer started.
Total HugeTLB memory allocated, 0
ikconfig 0.7 with /proc/config*
VFS: Disk quotas dquot_6.5.1
SGI XFS with ACLs, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1)
bootsplash 3.1.4-2004/02/19: looking for picture.... found (1024x768,
80505 bytes, v2).
Console: switching to colour frame buffer device 105x34
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
hda: WDC WD300BB-00AUA1, ATA DISK drive
hdc: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: Host Protected Area detected.
current capacity is 58631231 sectors (30019 MB)
native capacity is 58633344 sectors (30020 MB)
hda: 58631231 sectors (30019 MB) w/2048KiB Cache, CHS=58165/16/63
hda: hda1
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 Ultra2 SCSI adapter>
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs

(scsi0:A:3): 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
Vendor: PLEXTOR Model: CD-ROM PX-40TW Rev: 1.05
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:4): 20.000MB/s transfers (20.000MHz, offset 16)
Vendor: PLEXTOR Model: CD-R PX-W1210S Rev: 1.06
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:6): 80.000MB/s transfers (40.000MHz, offset 63, 16bit)
Vendor: IBM Model: DDYS-T36950N Rev: S80D
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:6:0: Tagged Queuing enabled. Depth 32
libata version 1.02 loaded.
Found Controller: IT8212 UDMA/ATA133 RAID Controller
Device 0 is IDE
Channel[0] BM-DMA at 0x9800-0x9807
Channel[1] BM-DMA at 0x9808-0x980F
scsi1 : ITE RAIDExpress133
Vendor: ITE Model: IT8212F Rev: 1.3
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
Attached scsi disk sda at scsi0, channel 0, id 6, lun 0
SCSI device sdb: 468883200 512-byte hdwr sectors (240068 MB)
sdb: asking for cache data failed
sdb: assuming drive cache: write through
sdb: sdb1
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: PS/2 Generic Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S3 S4 S5)
BIOS EDD facility v0.13 2004-Mar-09, 3 devices found
Please report your BIOS at http://linux.dell.com/edd/results.html
RAMDISK: Couldn't find valid RAM disk image starting at 0.
XFS mounting filesystem sda1
Ending clean XFS mount for filesystem: sda1
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 180k freed
Adding 248968k swap on /dev/sda7. Priority:-1 extents:1
XFS mounting filesystem sda2
Ending clean XFS mount for filesystem: sda2
XFS mounting filesystem sda3
Ending clean XFS mount for filesystem: sda3
XFS mounting filesystem sda5
Ending clean XFS mount for filesystem: sda5
XFS mounting filesystem sda6
Ending clean XFS mount for filesystem: sda6
XFS mounting filesystem sdb1
Ending clean XFS mount for filesystem: sdb1
Supermount version 2.0.4 for kernel 2.6
Intel(R) PRO/1000 Network Driver - version 5.2.30.1-k2
Copyright (c) 1999-2004 Intel Corporation.
eth0: Intel(R) PRO/1000 Network Connection
e1000: eth0 NIC Link is Up 100 Mbps Full Duplex
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1172 $ Ben Collins <bcollins@debian.org>
PCI: Setting latency timer of device 0000:00:0d.0 to 64
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22]
MMIO=[e6084000-e60847ff] Max Packet=[2048]
amd74xx: no version for "cleanup_module" found: kernel tainted.
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
NFORCE2: port 0x01f0 already claimed by ide0
NFORCE2: port 0x0170 already claimed by ide1
NFORCE2: neither IDE port enabled (BIOS)
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 49394 usecs
intel8x0: clocking to 47419
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.25.
PCI: Setting latency timer of device 0000:00:04.0 to 64
eth1: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:04.0
ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 21, pci mem 438cd000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ohci_hcd 0000:00:02.0: nVidia Corporation nForce2 USB Controller
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 20, pci mem 438fd000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0000:00:02.1: nVidia Corporation nForce2 USB Controller (#2)
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 22, pci mem 438ff000
Badness in get_phy_reg at drivers/ieee1394/ohci1394.c:238
Call Trace:
[<4381310e>] get_phy_reg+0x10e/0x120 [ohci1394]
[<43813f3c>] ohci_devctl+0x5c/0x5d0 [ohci1394]
[<02114a54>] delay_pmtmr+0x14/0x20
[<43816058>] ohci_irq_handler+0x588/0x830 [ohci1394]
[<0212827f>] do_timer+0xdf/0xf0
[<0210ac2a>] handle_IRQ_event+0x3a/0x70
[<0210b005>] do_IRQ+0xd5/0x1b0
=======================
[<43813193>] set_phy_reg+0x73/0x120 [ohci1394]
[<022d2c67>] hcd_submit_urb+0x137/0x160
[<438d1d40>] delayed_reset_bus+0x0/0xd0 [ieee1394]
[<43813f56>] ohci_devctl+0x76/0x5d0 [ohci1394]
[<438da3b7>] csr1212_fill_cache+0x97/0x100 [ieee1394]
[<438d1d40>] delayed_reset_bus+0x0/0xd0 [ieee1394]
[<438cf1a5>] hpsb_reset_bus+0x35/0x40 [ieee1394]
[<438d1df4>] delayed_reset_bus+0xb4/0xd0 [ieee1394]
[<02128094>] run_timer_softirq+0xd4/0x1d0
[<02130563>] rcu_process_callbacks+0x83/0x100
[<02123dbd>] __do_softirq+0x7d/0x80
[<0210b92e>] do_softirq+0x4e/0x60
=======================
[<0210b08b>] do_IRQ+0x15b/0x1b0

Badness in set_phy_reg at drivers/ieee1394/ohci1394.c:267
Call Trace:
[<43813230>] set_phy_reg+0x110/0x120 [ohci1394]
[<43813f56>] ohci_devctl+0x76/0x5d0 [ohci1394]
[<02114a54>] delay_pmtmr+0x14/0x20
[<43816058>] ohci_irq_handler+0x588/0x830 [ohci1394]
[<0212827f>] do_timer+0xdf/0xf0
[<0210ac2a>] handle_IRQ_event+0x3a/0x70
[<0210b005>] do_IRQ+0xd5/0x1b0
=======================
[<43813193>] set_phy_reg+0x73/0x120 [ohci1394]
[<022d2c67>] hcd_submit_urb+0x137/0x160
[<438d1d40>] delayed_reset_bus+0x0/0xd0 [ieee1394]
[<43813f56>] ohci_devctl+0x76/0x5d0 [ohci1394]
[<438da3b7>] csr1212_fill_cache+0x97/0x100 [ieee1394]
[<438d1d40>] delayed_reset_bus+0x0/0xd0 [ieee1394]
[<438cf1a5>] hpsb_reset_bus+0x35/0x40 [ieee1394]
[<438d1df4>] delayed_reset_bus+0xb4/0xd0 [ieee1394]
[<02128094>] run_timer_softirq+0xd4/0x1d0
[<02130563>] rcu_process_callbacks+0x83/0x100
[<02123dbd>] __do_softirq+0x7d/0x80
[<0210b92e>] do_softirq+0x4e/0x60
=======================
[<0210b08b>] do_IRQ+0x15b/0x1b0

ohci1394: fw-host0: SelfID received outside of bus reset sequence
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 256M @ 0xb0000000
ieee1394: Host added: ID:BUS[0-00:1023] GUID[8a1cc7ffff0020ed]
ip1394: $Rev: 1175 $ Ben Collins <bcollins@debian.org>
ip1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
usb 2-1: new full speed USB device using address 2
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 3 ports detected
usb 2-2: new low speed USB device using address 3
input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with
IntelliEye(TM)] on usb-0000:00:02.0-2
usbcore: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usb 2-1.1: new low speed USB device using address 4
input: USB HID v1.10 Keyboard [Microsoft Natural Keyboard Pro] on
usb-0000:00:02.0-1.1
input: USB HID v1.10 Device [Microsoft Natural Keyboard Pro] on
usb-0000:00:02.0-1.1
usb 3-1: new full speed USB device using address 2
nfs warning: mount version older than kernel
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
Real Time Clock Driver v1.12
eth0: no IPv6 routers present
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies,
Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 930 MBytes.
[fglrx] module loaded - fglrx 3.7.0 [Dec 18 2003] on minor 0
[fglrx] AGP detected, AgpState = 0x1f00421b (hardware caps of chipset)
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:03:00.0 into 8x mode
[fglrx] AGP enabled, AgpCommand = 0x1f004312 (selected caps)
[fglrx] free AGP = 256126976
[fglrx] max AGP = 256126976
[fglrx] free LFB = 116391936
[fglrx] max LFB = 116391936
[fglrx] free Inv = 0
[fglrx] max Inv = 0
[fglrx] total Inv = 0
[fglrx] total TIM = 0
[fglrx] total FB = 0
[fglrx] total AGP = 65536
inserting floppy driver for 2.6.5-rc3-mm1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
end_request: I/O error, dev fd0, sector 0
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 3, lun 0
sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 4, lun 0
sr: unaligned transfer
FAT: unable to read boot sector
ide-floppy driver 0.99.newide
hdc: No disk in drive

Attached is /proc/config.gz

Thanks,

Paul B.
[unhandled content-type:application/x-gzip][unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2005-03-22 14:02    [W:2.818 / U:23.312 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site