lkml.org 
[lkml]   [2003]   [May]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subjectlinux-2.5.69: acpi & ioapic: only 16 interrupts instead of 24
I have this problem where ACPI only recognizes 16 out of the 24
interrupts of my IOAPIC.

It's a VIA KT-400 chipset (Epox 8K9A3+), bios settings: ioapic on,
MPS-1.4. I'm using kernel 2.5.69 so my acpi-code is recent.

The relevant part of a dmesg of a acpi-2.5.69 boot:

ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, IRQ 0-23
Enabling APIC mode: Flat. Using 1 I/O APICs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.

Notice how it first says IRQ 0-23 for the APIC, then later claims that
there are 16 MP IRQ sources. Unfortunately, my on-board network card is
wired to one of the 8 lost irq's, and after booting my network is dead.

If I boot a non-acpi kernel, things look like this:

I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-20 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 24.
number of IO-APIC #2 registers: 24.

Then, there are 24 irq sources, and my network works fine.

Booting an acpi-kernel with commandline-argument 'pci=noacpi' hangs the
kernel after this line in the dmesg:

ide1 at 0x170-0x177,0x376 on irq 15

/proc/interrupts with acpi on:

CPU0
0: 7451442 IO-APIC-edge timer
1: 403 IO-APIC-edge i8042
2: 0 XT-PIC cascade
4: 8 IO-APIC-edge serial
8: 4 IO-APIC-edge rtc
9: 0 IO-APIC-edge acpi
11: 0 IO-APIC-edge VIA8233
12: 63 IO-APIC-edge i8042
14: 9161 IO-APIC-edge ide0
15: 1906 IO-APIC-edge ide1
17: 1507 IO-APIC-level ide2, ide4
18: 53 IO-APIC-level sym53c8xx
19: 0 IO-APIC-level EMU10K1

and with acpi off:

CPU0
0: 465649 IO-APIC-edge timer
1: 2511 IO-APIC-edge i8042
2: 0 XT-PIC cascade
4: 8 IO-APIC-edge serial
8: 4 IO-APIC-edge rtc
12: 63 IO-APIC-edge i8042
14: 33566 IO-APIC-edge ide0
15: 14231 IO-APIC-edge ide1
17: 6509 IO-APIC-level ide2, ide4
18: 43 IO-APIC-level sym53c8xx
19: 0 IO-APIC-level EMU10K1
22: 0 IO-APIC-level VIA8233
23: 24486 IO-APIC-level eth0

I'll attach a full dmesg for the acpi-kernel.
Googling didn't find anything to solve this, other than a tantalizing
hint this started between 2.5.44 and 2.5.44-ac1.

Thanks for your attention,
Jurriaan
Linux version 2.5.69 (root@middle) (gcc version 3.2.3) #3 Mon May 5 12:15:00 CEST 2003
Video mode to be used for restore is f00
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f5aa0
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 262128
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:16
HighMem zone: 32752 pages, LIFO batch:7
ACPI: RSDP (v000 KT400 ) @ 0x000f74a0
ACPI: RSDT (v001 KT400 AWRDACPI 16944.11825) @ 0x3fff3000
ACPI: FADT (v001 KT400 AWRDACPI 16944.11825) @ 0x3fff3040
ACPI: MADT (v001 KT400 AWRDACPI 16944.11825) @ 0x3fff71c0
ACPI: DSDT (v001 KT400 AWRDACPI 00000.04096) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x0] trigger[0x0])
ACPI: INT_SRC_OVR (bus[0] irq[0xe] global_irq[0xe] polarity[0x1] trigger[0x1])
ACPI: INT_SRC_OVR (bus[0] irq[0xf] global_irq[0xf] polarity[0x1] trigger[0x1])
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Building zonelist for node : 0
Kernel command line: root=/dev/hda1 video=matroxfb:vesa:0x11E,fv:85 hdb=scsi
ide_setup: hdb=scsi
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 2167.181 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 4276.22 BogoMIPS
Memory: 1032676k/1048512k available (2764k kernel code, 14892k reserved, 951k data, 436k init, 131008k highmem)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
-> /dev
-> /dev/console
-> /root
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 2700+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178003
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0003
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 0 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2166.0966 MHz.
..... host bus clock speed is 333.0379 MHz.
mtrr: v2.0 (20020519)
PCI: PCI BIOS revision 2.10 entry at 0xfb370, last bus=1
PCI: Using configuration type 1
BIO: pool of 256 setup, 14Kb (56 bytes/bio)
biovec pool[0]: 1 bvecs: 256 entries (12 bytes)
biovec pool[1]: 4 bvecs: 256 entries (48 bytes)
biovec pool[2]: 16 bvecs: 256 entries (192 bytes)
biovec pool[3]: 64 bvecs: 256 entries (768 bytes)
biovec pool[4]: 128 bvecs: 256 entries (1536 bytes)
biovec pool[5]: 256 bvecs: 256 entries (3072 bytes)
ACPI: Subsystem revision 20030418
tbxface-0117 [03] acpi_load_tables : ACPI Tables successfully acquired
Parsing all Control Methods:............................................................................................................................................
Table [DSDT] - 523 Objects with 49 Devices 140 Methods 28 Regions
ACPI Namespace successfully loaded at root c053369c
evxfevnt-0093 [04] acpi_enable : Transition to ACPI mode successful
evgpeblk-0740 [06] ev_create_gpe_block : GPE Block: [_GPE] 2 registers at 0000000000004020 on interrupt 9
evgpeblk-0745 [06] ev_create_gpe_block : GPE Block defined as GPE 0x00 to GPE 0x0F
evgpeblk-0262 [08] ev_save_method_info : Registered GPE method _L03 as GPE number 0x03
evgpeblk-0262 [08] ev_save_method_info : Registered GPE method _L05 as GPE number 0x05
evgpeblk-0262 [08] ev_save_method_info : Registered GPE method _L08 as GPE number 0x08
evgpeblk-0262 [08] ev_save_method_info : Registered GPE method _L09 as GPE number 0x09
evgpeblk-0262 [08] ev_save_method_info : Registered GPE method _L0E as GPE number 0x0E
evgpeblk-0262 [08] ev_save_method_info : Registered GPE method _L0A as GPE number 0x0A
Executing all Device _STA and_INI methods:.................................................
49 Devices found containing: 49 _STA, 2 _INI methods
Completing Region/Field/Buffer/Package initialization:.......................................................................
Initialized 23/28 Regions 11/13 Fields 19/20 Buffers 18/18 Packages (523 nodes)
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
pci_link-0256 [17] acpi_pci_link_get_curr: No IRQ resource found
ACPI: PCI Interrupt Link [ALKA] (IRQs 20, disabled)
pci_link-0256 [19] acpi_pci_link_get_curr: No IRQ resource found
ACPI: PCI Interrupt Link [ALKB] (IRQs 21, disabled)
pci_link-0256 [21] acpi_pci_link_get_curr: No IRQ resource found
ACPI: PCI Interrupt Link [ALKC] (IRQs 22, disabled)
pci_link-0256 [23] acpi_pci_link_get_curr: No IRQ resource found
ACPI: PCI Interrupt Link [ALKD] (IRQs 23, disabled)
block request queues:
128 requests per read queue
128 requests per write queue
8 requests per batch
enter congestion at 15
exit congestion at 17
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
pci_link-0256 [21] acpi_pci_link_get_curr: No IRQ resource found
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 0
pci_link-0256 [22] acpi_pci_link_get_curr: No IRQ resource found
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 0
pci_link-0256 [23] acpi_pci_link_get_curr: No IRQ resource found
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 0
pci_link-0256 [24] acpi_pci_link_get_curr: No IRQ resource found
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 0
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16)
00:00:08[A] -> 2-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17)
00:00:08[B] -> 2-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb9 -> IRQ 18)
00:00:08[C] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19)
00:00:08[D] -> 2-19 -> IRQ 19
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
pci_link-0502 [22] acpi_pci_link_get_irq : Link disabled
pci_link-0502 [22] acpi_pci_link_get_irq : Link disabled
pci_link-0502 [22] acpi_pci_link_get_irq : Link disabled
pci_link-0502 [22] acpi_pci_link_get_irq : Link disabled
pci_link-0502 [22] acpi_pci_link_get_irq : Link disabled
pci_link-0502 [22] acpi_pci_link_get_irq : Link disabled
pci_link-0502 [22] acpi_pci_link_get_irq : Link disabled
pci_link-0502 [22] acpi_pci_link_get_irq : Link disabled
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
pci_link-0502 [22] acpi_pci_link_get_irq : Link disabled
pci_link-0502 [22] acpi_pci_link_get_irq : Link disabled
pci_link-0502 [22] acpi_pci_link_get_irq : Link disabled
pci_link-0502 [22] acpi_pci_link_get_irq : Link disabled
pci_link-0502 [24] acpi_pci_link_get_irq : Link disabled
pci_irq-0256 [23] acpi_pci_irq_lookup : Invalid IRQ link routing entry
pci_irq-0295 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:10.0
ACPI: No IRQ known for interrupt pin A of device 00:10.0
pci_link-0502 [24] acpi_pci_link_get_irq : Link disabled
pci_irq-0256 [23] acpi_pci_irq_lookup : Invalid IRQ link routing entry
pci_irq-0295 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:10.1
ACPI: No IRQ known for interrupt pin B of device 00:10.1
pci_link-0502 [24] acpi_pci_link_get_irq : Link disabled
pci_irq-0256 [23] acpi_pci_irq_lookup : Invalid IRQ link routing entry
pci_irq-0295 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:10.2
ACPI: No IRQ known for interrupt pin C of device 00:10.2
pci_link-0502 [24] acpi_pci_link_get_irq : Link disabled
pci_irq-0256 [23] acpi_pci_irq_lookup : Invalid IRQ link routing entry
pci_irq-0295 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:10.3
ACPI: No IRQ known for interrupt pin D of device 00:10.3
pci_link-0502 [24] acpi_pci_link_get_irq : Link disabled
pci_irq-0256 [23] acpi_pci_irq_lookup : Invalid IRQ link routing entry
pci_irq-0295 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:11.1
ACPI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255
pci_link-0502 [24] acpi_pci_link_get_irq : Link disabled
pci_irq-0256 [23] acpi_pci_irq_lookup : Invalid IRQ link routing entry
pci_irq-0295 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:11.5
ACPI: No IRQ known for interrupt pin C of device 00:11.5
pci_link-0502 [24] acpi_pci_link_get_irq : Link disabled
pci_irq-0256 [23] acpi_pci_irq_lookup : Invalid IRQ link routing entry
pci_irq-0295 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:12.0
ACPI: No IRQ known for interrupt pin A of device 00:12.0
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Initializing RT netlink socket
Machine check exception polling timer started.
Enabling SEP on CPU 0
highmem bounce pool size: 64 pages
Journalled Block Device driver loaded
NTFS driver 2.1.4 [Flags: R/O].
udf: registering filesystem
ACPI: Power Button (FF) [PWRF]
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports C1 C2)
matroxfb: Matrox G450 detected
matroxfb: MTRR's turned on
matroxfb: 1600x1200x16bpp (virtual: 1600x5241)
matroxfb: framebuffer at 0xD8000000, mapped to 0xf8811000, size 33554432
Console: switching to colour frame buffer device 133x54
fb0: MATROX frame buffer device
pty: 256 Unix98 ptys configured
request_module: failed /sbin/modprobe -- parport_lowlevel. error = -16
lp: driver loaded but no devices found
Real Time Clock Driver v1.11
Software Watchdog Timer: 0.06, soft_margin: 60 sec, nowayout: 0
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA Apollo Pro KT400 chipset
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 128M @ 0xd0000000
[drm] Initialized mga 3.1.0 20021029 on minor 0
Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
lp0: using parport0 (polling).
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
via-rhine.c:v1.10-LK1.1.17 March-1-2003 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
pci_link-0502 [23] acpi_pci_link_get_irq : Link disabled
pci_irq-0256 [22] acpi_pci_irq_lookup : Invalid IRQ link routing entry
pci_irq-0295 [22] acpi_pci_irq_derive : Unable to derive IRQ for device 00:12.0
ACPI: No IRQ known for interrupt pin A of device 00:12.0
eth0: VIA VT6102 Rhine-II at 0xde002000, 00:04:61:02:0e:ea, IRQ 5.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
HPT374: IDE controller at PCI slot 00:0e.0
HPT374: chipset revision 7
HPT374: not 100% native mode: will probe irqs later
HPT37X: using 33MHz PCI clock
ide2: BM-DMA at 0xbc00-0xbc07, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdg:pio, hdh:pio
HPT37X: using 33MHz PCI clock
ide4: BM-DMA at 0xd000-0xd007, BIOS settings: hdi:DMA, hdj:pio
ide5: BM-DMA at 0xd008-0xd00f, BIOS settings: hdk:pio, hdl:pio
hde: WDC WD800JB-00CRA1, ATA DISK drive
ide2 at 0xac00-0xac07,0xb002 on irq 17
hdi: WDC WD800JB-00CRA1, ATA DISK drive
ide4 at 0xc000-0xc007,0xc402 on irq 17
VP_IDE: IDE controller at PCI slot 00:11.1
pci_link-0502 [23] acpi_pci_link_get_irq : Link disabled
pci_irq-0256 [22] acpi_pci_irq_lookup : Invalid IRQ link routing entry
pci_irq-0295 [22] acpi_pci_irq_derive : Unable to derive IRQ for device 00:11.1
ACPI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
hda: IBM-DTLA-307045, ATA DISK drive
hdb: LITE-ON LTR-40125W, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: Maxtor 4G120J6, ATA DISK drive
hdd: Maxtor 4G120J6, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hde: host protected area => 1
hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(100)
hde: hde1 hde2
hdi: host protected area => 1
hdi: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(100)
hdi: hdi1 hdi2
hda: host protected area => 1
hda: 90069840 sectors (46116 MB) w/1916KiB Cache, CHS=89355/16/63, UDMA(100)
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 >
hdc: host protected area => 1
hdc: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=14946/255/63, UDMA(133)
hdc: hdc1 hdc2
hdd: host protected area => 1
hdd: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=14946/255/63, UDMA(133)
hdd: hdd1 hdd2
ide-cd: passing drive hdb to ide-scsi emulation.
scsi HBA driver sym53c8xx didn't set a release method, please fix the template
sym.0.10.0: setting PCI_COMMAND_PARITY...
sym.0.10.0: setting PCI_COMMAND_INVALIDATE.
sym0: <860> rev 0x13 on pci bus 0 device 10 function 0 irq 18
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.16a
Vendor: TOSHIBA Model: DVD-ROM SD-M1401 Rev: 1007
Type: CD-ROM ANSI SCSI revision: 02
Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Vendor: YAMAHA Model: CRW2100S Rev: 1.0N
Type: CD-ROM ANSI SCSI revision: 02
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: LITE-ON Model: LTR-40125W Rev: WS05
Type: CD-ROM ANSI SCSI revision: 02
st: Version 20030413, fixed bufsize 32768, s/g segs 256
sym0:1: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 8)
sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
sym0:2: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 8)
sr1: scsi-1 drive
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 2, lun 0
sym0:5: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 7)
sr2: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr2 at scsi0, channel 0, id 5, lun 0
sr3: scsi3-mmc drive: 255x/48x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr3 at scsi1, channel 0, id 0, lun 0
matroxfb_crtc2: secondary head of fb0 was registered as fb1
drivers/usb/core/usb.c: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
drivers/usb/core/usb.c: registered new driver usbscanner
drivers/usb/image/scanner.c: 0.4.11:USB Scanner Driver
mice: PS/2 mouse device common for all mice
input: PC Speaker
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 3076.000 MB/sec
8regs_prefetch: 2972.000 MB/sec
32regs : 2144.000 MB/sec
32regs_prefetch: 1940.000 MB/sec
pIII_sse : 5772.000 MB/sec
pII_mmx : 5756.000 MB/sec
p5_mmx : 7628.000 MB/sec
raid5: using function: pIII_sse (5772.000 MB/sec)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
Advanced Linux Sound Architecture Driver Version 0.9.2 (Thu Mar 20 13:31:57 2003 UTC).
request_module: failed /sbin/modprobe -- snd-card-0. error = -16
pci_link-0502 [23] acpi_pci_link_get_irq : Link disabled
pci_irq-0256 [22] acpi_pci_irq_lookup : Invalid IRQ link routing entry
pci_irq-0295 [22] acpi_pci_irq_derive : Unable to derive IRQ for device 00:11.5
ACPI: No IRQ known for interrupt pin C of device 00:11.5
PCI: Setting latency timer of device 00:11.5 to 64
ALSA device list:
#0: VIA 8235 at 0xe400, irq 11
#1: Sound Blaster Live! (rev.7) at 0xa400, irq 19
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
md: Autodetecting RAID arrays.
md: autorun ...
md: considering hdi2 ...
md: adding hdi2 ...
md: hdi1 has different UUID to hdi2
md: adding hde2 ...
md: hde1 has different UUID to hdi2
md: created md1
md: bind<hde2>
md: bind<hdi2>
md: running: <hdi2><hde2>
md1: setting max_sectors to 128, segment boundary to 32767
raid0: looking at hdi2
raid0: comparing hdi2(17670656) with hdi2(17670656)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at hde2
raid0: comparing hde2(17670656) with hdi2(17670656)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 35341312 blocks.
raid0 : conf->smallest->size is 35341312 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 8 bytes for hash.
md: considering hdi1 ...
md: adding hdi1 ...
md: adding hde1 ...
md: created md0
md: bind<hde1>
md: bind<hdi1>
md: running: <hdi1><hde1>
md0: setting max_sectors to 128, segment boundary to 32767
raid0: looking at hdi1
raid0: comparing hdi1(60479872) with hdi1(60479872)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at hde1
raid0: comparing hde1(60479872) with hdi1(60479872)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 120959744 blocks.
raid0 : conf->smallest->size is 120959744 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 8 bytes for hash.
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 436k freed
Adding 2000368k swap on /dev/hda3. Priority:-1 extents:1
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on hda1, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hda8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hda8) for (hda8)
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hda6) for (hda6)
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hda5) for (hda5)
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hda10, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hda10) for (hda10)
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device md0, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (md0) for (md0)
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device md1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (md1) for (md1)
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hdc1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hdc1) for (hdc1)
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hdc2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hdc2) for (hdc2)
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hdd1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hdd1) for (hdd1)
Using r5 hash to sort names
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hdd2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hdd2) for (hdd2)
Using r5 hash to sort names
eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 786d, resetting...
eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
vmmon: no version magic, tainting kernel.
vmmon: module license 'unspecified' taints kernel.
/dev/vmmon: Module vmmon: registered with major=10 minor=165
/dev/vmmon: Module vmmon: initialized
vmnet: no version magic, tainting kernel.
vmnet: module license 'unspecified' taints kernel.
/dev/vmnet: open called by PID 606 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: up
bridge-eth0: attached
/dev/vmnet: open called by PID 629 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 1149 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 1148 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 1164 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 1169 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timed out, status 0003, PHY status 786d, resetting...
eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
\
 
 \ /
  Last update: 2005-03-22 13:35    [W:0.082 / U:0.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site