lkml.org 
[lkml]   [2003]   [Mar]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH] PC-9800 subarch. support for 2.5.64-ac3 (11/20) NIC
This is the patch to support NEC PC-9800 subarchitecture
against 2.5.64-ac3. (11/20)

C-bus(PC98's legacy bus like ISA) network cards support.
Change IO port and IRQ assign.
Add auto detect function for some cards.
PCI netwwork card works fine without patch.

Regards,
Osamu Tomita


diff -Nru linux-2.5.64/drivers/net/3c509.c linux98-2.5.64/drivers/net/3c509.c
--- linux-2.5.64/drivers/net/3c509.c 2003-03-05 11:22:46.000000000 +0900
+++ linux98-2.5.64/drivers/net/3c509.c 2003-03-05 11:45:08.000000000 +0900
@@ -56,6 +56,10 @@
v1.19b 08Nov2002 Marc Zyngier <maz@wild-wind.fr.eu.org>
- Introduce driver model for EISA cards.
*/
+/*
+ FIXES for PC-9800:
+ Shu Iwanaga: 3c569B(PC-9801 C-bus) support
+*/

#define DRV_NAME "3c509"
#define DRV_VERSION "1.19b"
@@ -257,7 +261,7 @@
};
#endif /* CONFIG_MCA */

-#ifdef __ISAPNP__
+#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
static struct isapnp_device_id el3_isapnp_adapters[] __initdata = {
{ ISAPNP_ANY_ID, ISAPNP_ANY_ID,
ISAPNP_VENDOR('T', 'C', 'M'), ISAPNP_FUNCTION(0x5090),
@@ -350,7 +354,7 @@
if (lp->pmdev)
pm_unregister(lp->pmdev);
#endif
-#ifdef __ISAPNP__
+#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
if (lp->type == EL3_PNP)
pnp_device_detach(to_pnp_dev(lp->dev));
#endif
@@ -368,12 +372,12 @@
int ioaddr, irq, if_port;
u16 phys_addr[3];
static int current_tag;
-#ifdef __ISAPNP__
+#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
static int pnp_cards;
struct pnp_dev *idev = NULL;
#endif /* __ISAPNP__ */

-#ifdef __ISAPNP__
+#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
if (nopnp == 1)
goto no_pnp;

@@ -421,6 +425,9 @@
no_pnp:
#endif /* __ISAPNP__ */

+#ifdef CONFIG_X86_PC9800
+ id_port = 0x71d0;
+#else
/* Select an open I/O location at 0x1*0 to do contention select. */
for ( ; id_port < 0x200; id_port += 0x10) {
if (check_region(id_port, 1))
@@ -435,6 +442,7 @@
printk(" WARNING: No I/O port available for 3c509 activation.\n");
return -ENODEV;
}
+#endif /* CONFIG_X86_PC9800 */
/* Next check for all ISA bus boards by sending the ID sequence to the
ID_PORT. We find cards past the first by setting the 'current_tag'
on cards as they are found. Cards with their tag set will not
@@ -465,7 +473,7 @@
phys_addr[i] = htons(id_read_eeprom(i));
}

-#ifdef __ISAPNP__
+#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
if (nopnp == 0) {
/* The ISA PnP 3c509 cards respond to the ID sequence.
This check is needed in order not to register them twice. */
@@ -490,9 +498,19 @@
{
unsigned int iobase = id_read_eeprom(8);
if_port = iobase >> 14;
+#ifdef CONFIG_X86_PC9800
+ ioaddr = 0x40d0 + ((iobase & 0x1f) << 8);
+#else
ioaddr = 0x200 + ((iobase & 0x1f) << 4);
+#endif
}
irq = id_read_eeprom(9) >> 12;
+#ifdef CONFIG_X86_PC9800
+ if (irq == 7)
+ irq = 6;
+ else if (irq == 15)
+ irq = 13;
+#endif

if (!(dev = init_etherdev(NULL, sizeof(struct el3_private))))
return -ENOMEM;
@@ -522,7 +540,11 @@
outb(0xd0 + ++current_tag, id_port);

/* Activate the adaptor at the EEPROM location. */
+#ifdef CONFIG_X86_PC9800
+ outb((ioaddr >> 8) | 0xe0, id_port);
+#else
outb((ioaddr >> 4) | 0xe0, id_port);
+#endif

EL3WINDOW(0);
if (inw(ioaddr) != 0x6d50) {
@@ -534,7 +556,7 @@
/* Free the interrupt so that some other card can use it. */
outw(0x0f00, ioaddr + WN0_IRQ);

-#ifdef __ISAPNP__
+#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
found: /* PNP jumps here... */
#endif /* __ISAPNP__ */

@@ -543,7 +565,7 @@
dev->irq = irq;
dev->if_port = if_port;
lp = dev->priv;
-#ifdef __ISAPNP__
+#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
lp->dev = &idev->dev;
#endif

@@ -1388,6 +1410,12 @@
outw(0x0001, ioaddr + 4);

/* Set the IRQ line. */
+#ifdef CONFIG_X86_PC9800
+ if (dev->irq == 6)
+ dev->irq = 7;
+ else if (dev->irq == 13)
+ dev->irq = 15;
+#endif
outw((dev->irq << 12) | 0x0f00, ioaddr + WN0_IRQ);

/* Set the station address in window 2 each time opened. */
@@ -1550,7 +1578,7 @@
MODULE_PARM_DESC(irq, "IRQ number(s) (assigned)");
MODULE_PARM_DESC(xcvr,"transceiver(s) (0=internal, 1=external)");
MODULE_PARM_DESC(max_interrupt_work, "maximum events handled per interrupt");
-#ifdef __ISAPNP__
+#if defined(__ISAPNP__) && !defined(CONFIG_X86_PC9800)
MODULE_PARM(nopnp, "i");
MODULE_PARM_DESC(nopnp, "disable ISA PnP support (0-1)");
MODULE_DEVICE_TABLE(isapnp, el3_isapnp_adapters);
diff -Nru linux-2.5.42/drivers/net/8390.h linux98-2.5.42/drivers/net/8390.h
--- linux-2.5.42/drivers/net/8390.h 2002-10-12 13:22:14.000000000 +0900
+++ linux98-2.5.42/drivers/net/8390.h 2002-10-15 23:03:22.000000000 +0900
@@ -123,7 +123,8 @@
#define inb_p(port) in_8(port)
#define outb_p(val,port) out_8(port,val)

-#elif defined(CONFIG_ARM_ETHERH) || defined(CONFIG_ARM_ETHERH_MODULE)
+#elif defined(CONFIG_ARM_ETHERH) || defined(CONFIG_ARM_ETHERH_MODULE) || \
+ defined(CONFIG_NET_CBUS)
#define EI_SHIFT(x) (ei_local->reg_offset[x])
#else
#define EI_SHIFT(x) (x)
diff -Nru linux-2.5.62-ac1/drivers/net/Kconfig linux98-2.5.62-ac1/drivers/net/Kconfig
--- linux-2.5.62-ac1/drivers/net/Kconfig 2003-02-18 07:56:53.000000000 +0900
+++ linux98-2.5.62-ac1/drivers/net/Kconfig 2003-02-21 11:07:56.000000000 +0900
@@ -663,7 +663,7 @@
as <file:Documentation/networking/net-modules.txt>.

config EL3
- tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support"
+ tristate "3c509/3c529 (MCA)/3c569B (98)/3c579 \"EtherLink III\" support"
depends on NET_VENDOR_3COM && (ISA || EISA || MCA)
---help---
If you have a network (Ethernet) card belonging to the 3Com
@@ -932,7 +932,7 @@
source "drivers/net/tulip/Kconfig"

config AT1700
- tristate "AT1700/1720 support (EXPERIMENTAL)"
+ tristate "AT1700/1720/RE1000Plus(C-Bus) support (EXPERIMENTAL)"
depends on NET_ETHERNET && (ISA || MCA) && EXPERIMENTAL
---help---
If you have a network (Ethernet) card of this type, say Y and read
@@ -978,7 +978,7 @@

config NET_ISA
bool "Other ISA cards"
- depends on NET_ETHERNET && ISA
+ depends on NET_ETHERNET && ISA && !X86_PC9800
---help---
If your network (Ethernet) card hasn't been mentioned yet and its
bus system (that's the way the cards talks to the other components
@@ -1176,6 +1176,55 @@
the Ethernet-HOWTO, available from
<http://www.linuxdoc.org/docs.html#howto>.

+config NET_CBUS
+ bool "NEC PC-9800 C-bus cards"
+ depends on NET_ETHERNET && ISA && X86_PC9800
+ ---help---
+ If your network (Ethernet) card hasn't been mentioned yet and its
+ bus system (that's the way the cards talks to the other components
+ of your computer) is NEC PC-9800 C-Bus, say Y.
+
+config NE2K_CBUS
+ tristate "Most NE2000-based Ethernet support"
+ depends on NET_CBUS
+
+config NE2K_CBUS_EGY98
+ bool "Melco EGY-98 support"
+ depends on NE2K_CBUS
+
+config NE2K_CBUS_LGY98
+ bool "Melco LGY-98 support"
+ depends on NE2K_CBUS
+
+config NE2K_CBUS_ICM
+ bool "ICM IF-27xxET support"
+ depends on NE2K_CBUS
+
+config NE2K_CBUS_IOLA98
+ bool "I-O DATA LA-98 support"
+ depends on NE2K_CBUS
+
+config NE2K_CBUS_CNET98EL
+ bool "Contec C-NET(98)E/L support"
+ depends on NE2K_CBUS
+
+config NE2K_CBUS_CNET98EL_IO_BASE
+ hex "C-NET(98)E/L I/O base address (0xaaed or 0x55ed)"
+ depends on NE2K_CBUS_CNET98EL
+ default "0xaaed"
+
+config NE2K_CBUS_ATLA98
+ bool "Allied Telesis LA-98 Support"
+ depends on NE2K_CBUS
+
+config NE2K_CBUS_BDN
+ bool "ELECOM Laneed LD-BDN[123]A Support"
+ depends on NE2K_CBUS
+
+config NE2K_CBUS_NEC108
+ bool "NEC PC-9801-108 Support"
+ depends on NE2K_CBUS
+
config SKMC
tristate "SKnet MCA support"
depends on NET_ETHERNET && MCA
diff -Nru linux-2.5.63/drivers/net/Makefile linux98-2.5.63/drivers/net/Makefile
--- linux-2.5.63/drivers/net/Makefile 2003-02-25 13:54:39.000000000 +0900
+++ linux98-2.5.63/drivers/net/Makefile 2003-02-25 16:14:35.000000000 +0900
@@ -81,6 +81,7 @@
obj-$(CONFIG_WD80x3) += wd.o 8390.o
obj-$(CONFIG_EL2) += 3c503.o 8390.o
obj-$(CONFIG_NE2000) += ne.o 8390.o
+obj-$(CONFIG_NE2K_CBUS) += ne.o 8390.o
obj-$(CONFIG_NE2_MCA) += ne2.o 8390.o
obj-$(CONFIG_HPLAN) += hp.o 8390.o
obj-$(CONFIG_HPLAN_PLUS) += hp-plus.o 8390.o
diff -Nru linux-2.5.42/drivers/net/Makefile.lib linux98-2.5.42/drivers/net/Makefile.lib
--- linux-2.5.42/drivers/net/Makefile.lib 2002-10-12 13:22:18.000000000 +0900
+++ linux98-2.5.42/drivers/net/Makefile.lib 2002-10-15 23:03:22.000000000 +0900
@@ -19,6 +19,7 @@
obj-$(CONFIG_MACMACE) += crc32.o
obj-$(CONFIG_MIPS_AU1000_ENET) += crc32.o
obj-$(CONFIG_NATSEMI) += crc32.o
+obj-$(CONFIG_NE2K_CBUS) += crc32.o
obj-$(CONFIG_PCMCIA_FMVJ18X) += crc32.o
obj-$(CONFIG_PCMCIA_SMC91C92) += crc32.o
obj-$(CONFIG_PCMCIA_XIRTULIP) += crc32.o
diff -Nru linux-2.5.64-ac1/drivers/net/Space.c linux98-2.5.64-ac1/drivers/net/Space.c
--- linux-2.5.64-ac1/drivers/net/Space.c 2003-03-07 08:52:03.000000000 +0900
+++ linux98-2.5.64-ac1/drivers/net/Space.c 2003-03-07 13:30:51.000000000 +0900
@@ -229,7 +229,7 @@
#ifdef CONFIG_E2100 /* Cabletron E21xx series. */
{e2100_probe, 0},
#endif
-#ifdef CONFIG_NE2000 /* ISA (use ne2k-pci for PCI cards) */
+#if defined(CONFIG_NE2000) || defined(CONFIG_NE2K_CBUS) /* ISA & PC-9800 CBUS (use ne2k-pci for PCI cards) */
{ne_probe, 0},
#endif
#ifdef CONFIG_LANCE /* ISA/VLB (use pcnet32 for PCI cards) */
diff -Nru linux-2.5.57/drivers/net/at1700.c linux98-2.5.57/drivers/net/at1700.c
--- linux-2.5.57/drivers/net/at1700.c 2003-01-14 09:31:51.000000000 +0900
+++ linux98-2.5.57/drivers/net/at1700.c 2003-01-14 09:55:53.000000000 +0900
@@ -34,6 +34,10 @@
only is it difficult to detect, it also moves around in I/O space in
response to inb()s from other device probes!
*/
+/*
+ 99/03/03 Allied Telesis RE1000 Plus support by T.Hagawa
+ 99/12/30 port to 2.3.35 by K.Takai
+*/

#include <linux/config.h>
#include <linux/errno.h>
@@ -76,10 +80,17 @@
* ISA
*/

+#ifndef CONFIG_X86_PC9800
static int at1700_probe_list[] __initdata = {
0x260, 0x280, 0x2a0, 0x240, 0x340, 0x320, 0x380, 0x300, 0
};

+#else /* CONFIG_X86_PC9800 */
+static int at1700_probe_list[] __initdata = {
+ 0x1d6, 0x1d8, 0x1da, 0x1d4, 0xd4, 0xd2, 0xd8, 0xd0, 0
+};
+
+#endif /* CONFIG_X86_PC9800 */
/*
* MCA
*/
@@ -122,6 +133,7 @@


/* Offsets from the base address. */
+#ifndef CONFIG_X86_PC9800
#define STATUS 0
#define TX_STATUS 0
#define RX_STATUS 1
@@ -136,6 +148,7 @@
#define TX_START 10
#define COL16CNTL 11 /* Controll Reg for 16 collisions */
#define MODE13 13
+#define RX_CTRL 14
/* Configuration registers only on the '865A/B chips. */
#define EEPROM_Ctrl 16
#define EEPROM_Data 17
@@ -144,8 +157,39 @@
#define IOCONFIG 18 /* Either read the jumper, or move the I/O. */
#define IOCONFIG1 19
#define SAPROM 20 /* The station address PROM, if no EEPROM. */
+#define MODE24 24
#define RESET 31 /* Write to reset some parts of the chip. */
#define AT1700_IO_EXTENT 32
+#define PORT_OFFSET(o) (o)
+#else /* CONFIG_X86_PC9800 */
+#define STATUS (0x0000)
+#define TX_STATUS (0x0000)
+#define RX_STATUS (0x0001)
+#define TX_INTR (0x0200)/* Bit-mapped interrupt enable registers. */
+#define RX_INTR (0x0201)
+#define TX_MODE (0x0400)
+#define RX_MODE (0x0401)
+#define CONFIG_0 (0x0600)/* Misc. configuration settings. */
+#define CONFIG_1 (0x0601)
+/* Run-time register bank 2 definitions. */
+#define DATAPORT (0x0800)/* Word-wide DMA or programmed-I/O dataport. */
+#define TX_START (0x0a00)
+#define COL16CNTL (0x0a01)/* Controll Reg for 16 collisions */
+#define MODE13 (0x0c01)
+#define RX_CTRL (0x0e00)
+/* Configuration registers only on the '865A/B chips. */
+#define EEPROM_Ctrl (0x1000)
+#define EEPROM_Data (0x1200)
+#define CARDSTATUS 16 /* FMV-18x Card Status */
+#define CARDSTATUS1 17 /* FMV-18x Card Status */
+#define IOCONFIG (0x1400)/* Either read the jumper, or move the I/O. */
+#define IOCONFIG1 (0x1600)
+#define SAPROM 20 /* The station address PROM, if no EEPROM. */
+#define MODE24 (0x1800)/* The station address PROM, if no EEPROM. */
+#define RESET (0x1e01)/* Write to reset some parts of the chip. */
+#define PORT_OFFSET(o) ({ int _o_ = (o); (_o_ & ~1) * 0x100 + (_o_ & 1); })
+#endif /* CONFIG_X86_PC9800 */
+

#define TX_TIMEOUT 10

@@ -225,8 +269,20 @@
int slot, ret = -ENODEV;
struct net_local *lp;

+#ifndef CONFIG_X86_PC9800
if (!request_region(ioaddr, AT1700_IO_EXTENT, dev->name))
return -EBUSY;
+#else
+ for (i = 0; i < 0x2000; i += 0x0200) {
+ if (!request_region(ioaddr + i, 2, dev->name)) {
+ while (i > 0) {
+ i -= 0x0200;
+ release_region(ioaddr + i, 2);
+ }
+ return -EBUSY;
+ }
+ }
+#endif

/* Resetting the chip doesn't reset the ISA interface, so don't bother.
That means we have to be careful with the register values we probe for.
@@ -317,10 +373,17 @@
/* Reset the internal state machines. */
outb(0, ioaddr + RESET);

- if (is_at1700)
+ if (is_at1700) {
+#ifndef CONFIG_X86_PC9800
irq = at1700_irqmap[(read_eeprom(ioaddr, 12)&0x04)
| (read_eeprom(ioaddr, 0)>>14)];
- else {
+#else
+ {
+ char re1000plus_irqmap[4] = {3, 5, 6, 12};
+ irq = re1000plus_irqmap[inb(ioaddr + IOCONFIG1) >> 6];
+ }
+#endif
+ } else {
/* Check PnP mode for FMV-183/184/183A/184A. */
/* This PnP routine is very poor. IO and IRQ should be known. */
if (inb(ioaddr + CARDSTATUS1) & 0x20) {
@@ -392,18 +455,22 @@
/* Set the station address in bank zero. */
outb(0x00, ioaddr + CONFIG_1);
for (i = 0; i < 6; i++)
- outb(dev->dev_addr[i], ioaddr + 8 + i);
+ outb(dev->dev_addr[i], ioaddr + PORT_OFFSET(8 + i));

/* Switch to bank 1 and set the multicast table to accept none. */
outb(0x04, ioaddr + CONFIG_1);
for (i = 0; i < 8; i++)
- outb(0x00, ioaddr + 8 + i);
+ outb(0x00, ioaddr + PORT_OFFSET(8 + i));


/* Switch to bank 2 */
/* Lock our I/O address, and set manual processing mode for 16 collisions. */
outb(0x08, ioaddr + CONFIG_1);
+#ifndef CONFIG_X86_PC9800
outb(dev->if_port, ioaddr + MODE13);
+#else
+ outb(0, ioaddr + MODE13);
+#endif
outb(0x00, ioaddr + COL16CNTL);

if (net_debug)
@@ -447,7 +514,12 @@
kfree(dev->priv);
dev->priv = NULL;
err_out:
+#ifndef CONFIG_X86_PC9800
release_region(ioaddr, AT1700_IO_EXTENT);
+#else
+ for (i = 0; i < 0x2000; i += 0x0200)
+ release_region(ioaddr + i, 2);
+#endif
return ret;
}

@@ -459,7 +531,11 @@
#define EE_DATA_READ 0x80 /* EEPROM chip data out, in reg. 17. */

/* Delay between EEPROM clock transitions. */
+#ifndef CONFIG_X86_PC9800
#define eeprom_delay() do { } while (0)
+#else
+#define eeprom_delay() __asm__ ("out%B0 %%al,%0" :: "N"(0x5f))
+#endif

/* The EEPROM commands include the alway-set leading bit. */
#define EE_WRITE_CMD (5 << 6)
@@ -542,12 +618,12 @@
inw (ioaddr + STATUS), inb (ioaddr + TX_STATUS) & 0x80
? "IRQ conflict" : "network cable problem");
printk ("%s: timeout registers: %04x %04x %04x %04x %04x %04x %04x %04x.\n",
- dev->name, inw (ioaddr + 0), inw (ioaddr + 2), inw (ioaddr + 4),
- inw (ioaddr + 6), inw (ioaddr + 8), inw (ioaddr + 10),
- inw (ioaddr + 12), inw (ioaddr + 14));
+ dev->name, inw(ioaddr + TX_STATUS), inw(ioaddr + TX_INTR), inw(ioaddr + TX_MODE),
+ inw(ioaddr + CONFIG_0), inw(ioaddr + DATAPORT), inw(ioaddr + TX_START),
+ inw(ioaddr + MODE13 - 1), inw(ioaddr + RX_CTRL));
lp->stats.tx_errors++;
/* ToDo: We should try to restart the adaptor... */
- outw (0xffff, ioaddr + 24);
+ outw(0xffff, ioaddr + MODE24);
outw (0xffff, ioaddr + TX_STATUS);
outb (0x5a, ioaddr + CONFIG_0);
outb (0xe8, ioaddr + CONFIG_1);
@@ -704,7 +780,7 @@
dev->name, inb(ioaddr + RX_MODE), status);
#ifndef final_version
if (status == 0) {
- outb(0x05, ioaddr + 14);
+ outb(0x05, ioaddr + RX_CTRL);
break;
}
#endif
@@ -724,7 +800,7 @@
dev->name, pkt_len);
/* Prime the FIFO and then flush the packet. */
inw(ioaddr + DATAPORT); inw(ioaddr + DATAPORT);
- outb(0x05, ioaddr + 14);
+ outb(0x05, ioaddr + RX_CTRL);
lp->stats.rx_errors++;
break;
}
@@ -734,7 +810,7 @@
dev->name, pkt_len);
/* Prime the FIFO and then flush the packet. */
inw(ioaddr + DATAPORT); inw(ioaddr + DATAPORT);
- outb(0x05, ioaddr + 14);
+ outb(0x05, ioaddr + RX_CTRL);
lp->stats.rx_dropped++;
break;
}
@@ -761,7 +837,7 @@
if ((inb(ioaddr + RX_MODE) & 0x40) == 0x40)
break;
inw(ioaddr + DATAPORT); /* dummy status read */
- outb(0x05, ioaddr + 14);
+ outb(0x05, ioaddr + RX_CTRL);
}

if (net_debug > 5)
@@ -851,7 +927,7 @@
/* Switch to bank 1 and set the multicast table. */
outw((saved_bank & ~0x0C00) | 0x0480, ioaddr + CONFIG_0);
for (i = 0; i < 8; i++)
- outb(mc_filter[i], ioaddr + 8 + i);
+ outb(mc_filter[i], ioaddr + PORT_OFFSET(8 + i));
memcpy(lp->mc_filter, mc_filter, sizeof(mc_filter));
outw(saved_bank, ioaddr + CONFIG_0);
}
@@ -861,7 +937,12 @@

#ifdef MODULE
static struct net_device dev_at1700;
+#ifndef CONFIG_X86_PC9800
static int io = 0x260;
+#else
+static int io = 0xd0;
+#endif
+
static int irq;

MODULE_PARM(io, "i");
@@ -901,7 +982,15 @@

/* If we don't do this, we can't re-insmod it later. */
free_irq(dev_at1700.irq, NULL);
+#ifndef CONFIG_X86_PC9800
release_region(dev_at1700.base_addr, AT1700_IO_EXTENT);
+#else
+ {
+ int i;
+ for (i = 0; i < 0x2000; i += 0x200)
+ release_region(dev_at1700.base_addr + i, 2);
+ }
+#endif
}
#endif /* MODULE */
MODULE_LICENSE("GPL");
diff -Nru linux-2.5.61/drivers/net/ne.c linux98-2.5.61/drivers/net/ne.c
--- linux-2.5.61/drivers/net/ne.c 2003-02-15 08:51:42.000000000 +0900
+++ linux98-2.5.61/drivers/net/ne.c 2003-02-16 11:49:42.000000000 +0900
@@ -109,6 +109,10 @@
{"PCM-4823", "PCM-4823", {0x00, 0xc0, 0x6c}}, /* Broken Advantech MoBo */
{"REALTEK", "RTL8019", {0x00, 0x00, 0xe8}}, /* no-name with Realtek chip */
{"LCS-8834", "LCS-8836", {0x04, 0x04, 0x37}}, /* ShinyNet (SET) */
+ {"LA/T-98?", "LA/T-98", {0x00, 0xa0, 0xb0}}, /* I/O Data */
+ {"EGY-98?", "EGY-98", {0x00, 0x40, 0x26}}, /* Melco EGY98 */
+ {"ICM?", "ICM-27xx-ET", {0x00, 0x80, 0xc8}}, /* ICM IF-27xx-ET */
+ {"CNET-98/EL?", "CNET(98)E/L", {0x00, 0x80, 0x4C}}, /* Contec CNET-98/EL */
{0,}
};
#endif
@@ -116,9 +120,10 @@
/* ---- No user-serviceable parts below ---- */

#define NE_BASE (dev->base_addr)
-#define NE_CMD 0x00
-#define NE_DATAPORT 0x10 /* NatSemi-defined port window offset. */
-#define NE_RESET 0x1f /* Issue a read to reset, a write to clear. */
+#define NE_CMD EI_SHIFT(0x00)
+#define NE_DATAPORT EI_SHIFT(0x10) /* NatSemi-defined port window offset. */
+#define NE_RESET EI_SHIFT(0x1f) /* Issue a read to reset, a write to clear. */
+
#define NE_IO_EXTENT 0x20

#define NE1SM_START_PG 0x20 /* First page of TX buffer */
@@ -126,9 +131,15 @@
#define NESM_START_PG 0x40 /* First page of TX buffer */
#define NESM_STOP_PG 0x80 /* Last page +1 of RX ring */

+#ifdef CONFIG_NET_CBUS
+#include "ne2k_cbus.h"
+#endif
+
int ne_probe(struct net_device *dev);
static int ne_probe1(struct net_device *dev, int ioaddr);
+#ifndef CONFIG_NET_CBUS
static int ne_probe_isapnp(struct net_device *dev);
+#endif

static int ne_open(struct net_device *dev);
static int ne_close(struct net_device *dev);
@@ -163,6 +174,8 @@
E2010 starts at 0x100 and ends at 0x4000.
E2010-x starts at 0x100 and ends at 0xffff. */

+#ifndef CONFIG_NET_CBUS
+
int __init ne_probe(struct net_device *dev)
{
unsigned int base_addr = dev->base_addr;
@@ -236,6 +249,116 @@
return -ENODEV;
}

+#else /* CONFIG_NET_CBUS */
+
+int __init ne_probe(struct net_device *dev)
+{
+ unsigned int base_addr = dev->base_addr;
+
+ SET_MODULE_OWNER(dev);
+
+ if (ei_debug > 2)
+ printk(KERN_DEBUG "ne_probe(): entered.\n");
+
+ /* If CONFIG_NET_CBUS,
+ we need dev->priv->reg_offset BEFORE to probe */
+ if (ne2k_cbus_init(dev) != 0) {
+ return -ENOMEM;
+ }
+
+ /* First check any supplied i/o locations. User knows best. <cough> */
+ if (base_addr > 0) {
+ int result;
+ const struct ne2k_cbus_hwinfo *hw = ne2k_cbus_get_hwinfo((int)(dev->mem_start & NE2K_CBUS_HARDWARE_TYPE_MASK));
+
+ if (ei_debug > 2)
+ printk(KERN_DEBUG "ne_probe(): call ne_probe_cbus(base_addr=0x%x)\n", base_addr);
+
+ result = ne_probe_cbus(dev, hw, base_addr);
+ if (result != 0)
+ ne2k_cbus_destroy(dev);
+
+ return result;
+ }
+
+ if (ei_debug > 2)
+ printk(KERN_DEBUG "ne_probe(): base_addr is not specified.\n");
+
+#ifndef MODULE
+ /* Last resort. The semi-risky C-Bus auto-probe. */
+ if (ei_debug > 2)
+ printk(KERN_DEBUG "ne_probe(): auto-probe start.\n");
+
+ {
+ const struct ne2k_cbus_hwinfo *hw = ne2k_cbus_get_hwinfo((int)(dev->mem_start & NE2K_CBUS_HARDWARE_TYPE_MASK));
+
+ if (hw && hw->hwtype) {
+ const unsigned short *plist;
+ for (plist = hw->portlist; *plist; plist++) {
+ const struct ne2k_cbus_region *rlist;
+ for (rlist = hw->regionlist; rlist->range; rlist++) {
+ if (check_region(*plist+rlist->start, rlist->range))
+ break;
+ }
+ if (rlist->range) {
+ /* check_region() failed */
+ continue; /* try next base port */
+ }
+ /* check_region() succeeded */
+ if (ne_probe_cbus(dev,hw,*plist) == 0)
+ return 0;
+ }
+ } else {
+ for (hw = &ne2k_cbus_hwinfo_list[0]; hw->hwtype; hw++) {
+ const unsigned short *plist;
+ for(plist=hw->portlist; *plist; plist++){
+ const struct ne2k_cbus_region *rlist;
+
+ for (rlist = hw->regionlist; rlist->range; rlist++) {
+ if (check_region(*plist+rlist->start, rlist->range))
+ break;
+ }
+ if (rlist->range) {
+ /* check_region() failed */
+ continue; /* try next base port */
+ }
+ /* check_region() succeeded */
+ if (ne_probe_cbus(dev,hw,*plist) == 0)
+ return 0;
+ }
+ }
+ }
+ }
+#endif
+
+ ne2k_cbus_destroy(dev);
+
+ return -ENODEV;
+}
+
+static int __init ne_probe_cbus(struct net_device *dev, const struct ne2k_cbus_hwinfo *hw, int ioaddr)
+{
+ if (ei_debug > 2)
+ printk(KERN_DEBUG "ne_probe_cbus(): entered. (called from %p)\n",
+ __builtin_return_address(0));
+
+ if (hw && hw->hwtype) {
+ ne2k_cbus_set_hwtype(dev, hw, ioaddr);
+ return ne_probe1(dev, ioaddr);
+ } else {
+ /* auto detect */
+
+ printk(KERN_DEBUG "ne_probe_cbus(): try to determine hardware types.\n");
+ for (hw = &ne2k_cbus_hwinfo_list[0]; hw->hwtype; hw++) {
+ ne2k_cbus_set_hwtype(dev, hw, ioaddr);
+ if (ne_probe1(dev, ioaddr)==0)
+ return 0;
+ }
+ }
+ return ENODEV;
+}
+#endif /* !CONFIG_NET_CBUS */
+
static int __init ne_probe1(struct net_device *dev, int ioaddr)
{
int i;
@@ -243,30 +366,62 @@
int wordlength = 2;
const char *name = NULL;
int start_page, stop_page;
- int neX000, ctron, copam, bad_card;
+ int neX000, bad_card;
+#ifndef CONFIG_NET_CBUS
+ int ctron, copam;
+#endif
int reg0, ret;
static unsigned version_printed;
+#ifdef CONFIG_NET_CBUS
+ const struct ne2k_cbus_hwinfo *hw = ne2k_cbus_get_hwinfo((int)(dev->mem_start & NE2K_CBUS_HARDWARE_TYPE_MASK));
+ struct ei_device *ei_local = (struct ei_device *)(dev->priv);
+#endif
+
+#ifdef CONFIG_NE2K_CBUS_CNET98EL
+ if (hw->hwtype == NE2K_CBUS_HARDWARE_TYPE_CNET98EL) {
+ outb_p(0, CONFIG_NE2K_CBUS_CNET98EL_IO_BASE);
+ /* udelay(5000); */
+ outb_p(1, CONFIG_NE2K_CBUS_CNET98EL_IO_BASE);
+ /* udelay(5000); */
+ outb_p((ioaddr & 0xf000) >> 8 | 0x08 | 0x01, CONFIG_NE2K_CBUS_CNET98EL_IO_BASE + 2);
+ /* udelay(5000); */
+ }
+#endif

+#ifndef CONFIG_NET_CBUS
if (!request_region(ioaddr, NE_IO_EXTENT, dev->name))
return -EBUSY;
+#else /* CONFIG_NET_CBUS */
+ {
+ const struct ne2k_cbus_region *rlist;
+ for (rlist = hw->regionlist; rlist->range; rlist++) {
+ if (!request_region(ioaddr + rlist->start,
+ rlist->range, dev->name))
+ return -EBUSY;
+ }
+ }
+#endif /* !CONFIG_NET_CBUS */

- reg0 = inb_p(ioaddr);
+ reg0 = inb_p(ioaddr + EI_SHIFT(0));
if (reg0 == 0xFF) {
ret = -ENODEV;
goto err_out;
}

/* Do a preliminary verification that we have a 8390. */
+#ifdef CONFIG_NE2K_CBUS_CNET98EL
+ if (hw->hwtype != NE2K_CBUS_HARDWARE_TYPE_CNET98EL)
+#endif
{
int regd;
outb_p(E8390_NODMA+E8390_PAGE1+E8390_STOP, ioaddr + E8390_CMD);
- regd = inb_p(ioaddr + 0x0d);
- outb_p(0xff, ioaddr + 0x0d);
+ regd = inb_p(ioaddr + EI_SHIFT(0x0d));
+ outb_p(0xff, ioaddr + EI_SHIFT(0x0d));
outb_p(E8390_NODMA+E8390_PAGE0, ioaddr + E8390_CMD);
inb_p(ioaddr + EN0_COUNTER0); /* Clear the counter by reading. */
if (inb_p(ioaddr + EN0_COUNTER0) != 0) {
outb_p(reg0, ioaddr);
- outb_p(regd, ioaddr + 0x0d); /* Restore the old values. */
+ outb_p(regd, ioaddr + EI_SHIFT(0x0d)); /* Restore the old values. */
ret = -ENODEV;
goto err_out;
}
@@ -290,6 +445,11 @@
{
unsigned long reset_start_time = jiffies;

+#ifdef CONFIG_NET_CBUS
+ /* derived from CNET98EL-patch for bad clones */
+ outb_p(E8390_NODMA | E8390_STOP, ioaddr+E8390_CMD);
+#endif
+
/* DON'T change these to inb_p/outb_p or reset will fail on clones. */
outb(inb(ioaddr + NE_RESET), ioaddr + NE_RESET);

@@ -308,15 +468,86 @@
outb_p(0xff, ioaddr + EN0_ISR); /* Ack all intr. */
}

+#ifdef CONFIG_NE2K_CBUS_CNET98EL
+ if (hw->hwtype == NE2K_CBUS_HARDWARE_TYPE_CNET98EL) {
+ static const char pat[32] ="AbcdeFghijKlmnoPqrstUvwxyZ789012";
+ char buf[32];
+ int maxwait = 200;
+
+ if (ei_debug > 2) {
+ printk(" [CNET98EL-specific initialize...");
+ }
+ outb_p(E8390_NODMA | E8390_STOP, ioaddr+E8390_CMD); /* 0x20|0x1 */
+ i=inb(ioaddr);
+ if ((i & ~0x2) != (0x20 | 0x01))
+ return ENODEV;
+ if ((inb(ioaddr + 0x7) & 0x80) != 0x80)
+ return ENODEV;
+ outb_p(E8390_RXOFF, ioaddr+EN0_RXCR); /* out(ioaddr+0xc, 0x20) */
+ /* outb_p(ENDCFG_WTS|ENDCFG_FT1|ENDCFG_LS, ioaddr+EN0_DCFG); */
+ outb_p(ENDCFG_WTS|0x48, ioaddr+EN0_DCFG); /* 0x49 */
+ outb_p(CNET98EL_START_PG, ioaddr+EN0_STARTPG);
+ outb_p(CNET98EL_STOP_PG, ioaddr+EN0_STOPPG);
+ if (ei_debug > 2) {
+ printk("memory check");
+ }
+ for (i = 0; i < 65536; i += 1024) {
+ if (ei_debug > 2) {
+ printk(" %04x",i);
+ }
+ ne2k_cbus_writemem(dev,ioaddr, i, pat, 32);
+ while (((inb(ioaddr + EN0_ISR) & ENISR_RDC) != ENISR_RDC) && --maxwait)
+ ;
+ ne2k_cbus_readmem(dev, ioaddr, i, buf, 32);
+ if (memcmp(pat, buf, 32)) {
+ if (ei_debug > 2) {
+ printk(" failed.");
+ }
+ break;
+ }
+ }
+ if (i != 16384) {
+ if (ei_debug > 2) {
+ printk("] ");
+ }
+ printk("memory failure at %x\n", i);
+ return ENODEV;
+ }
+ if (ei_debug > 2) {
+ printk(" good...");
+ }
+ if (!dev->irq) {
+ if (ei_debug > 2) {
+ printk("] ");
+ }
+ printk("IRQ must be specified for C-NET(98)E/L. probe failed.\n");
+ return ENODEV;
+ }
+ outb((dev->irq>5) ? (dev->irq&4):(dev->irq>>1), ioaddr + (0x2 | 0x400));
+ outb(0x7e, ioaddr + (0x4 | 0x400));
+ ne2k_cbus_readmem(dev, ioaddr, 16384, SA_prom, 32);
+ outb(0xff, ioaddr + EN0_ISR);
+ if (ei_debug > 2) {
+ printk("done]");
+ }
+ } else
+#endif /* CONFIG_NE2K_CBUS_CNET98EL */
/* Read the 16 bytes of station address PROM.
We must first initialize registers, similar to NS8390_init(eifdev, 0).
We can't reliably read the SAPROM address without this.
(I learned the hard way!). */
{
- struct {unsigned char value, offset; } program_seq[] =
+ struct {unsigned char value; unsigned short offset;} program_seq[] =
{
{E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/
+#ifndef CONFIG_NET_CBUS
{0x48, EN0_DCFG}, /* Set byte-wide (0x48) access. */
+#else
+ /* NEC PC-9800: some board can only handle word-wide access? */
+ {0x48 | ENDCFG_WTS, EN0_DCFG}, /* Set word-wide (0x48) access. */
+ {16384 / 256, EN0_STARTPG},
+ {32768 / 256, EN0_STOPPG},
+#endif
{0x00, EN0_RCNTLO}, /* Clear the count regs. */
{0x00, EN0_RCNTHI},
{0x00, EN0_IMR}, /* Mask completion irq. */
@@ -332,29 +563,42 @@

for (i = 0; i < sizeof(program_seq)/sizeof(program_seq[0]); i++)
outb_p(program_seq[i].value, ioaddr + program_seq[i].offset);
-
- }
+#ifndef CONFIG_NET_CBUS
for(i = 0; i < 32 /*sizeof(SA_prom)*/; i+=2) {
SA_prom[i] = inb(ioaddr + NE_DATAPORT);
SA_prom[i+1] = inb(ioaddr + NE_DATAPORT);
if (SA_prom[i] != SA_prom[i+1])
wordlength = 1;
}
+#else
+ insw(ioaddr + NE_DATAPORT, SA_prom, 32 >> 1);
+#endif
+
+ }

if (wordlength == 2)
{
for (i = 0; i < 16; i++)
SA_prom[i] = SA_prom[i+i];
+#ifndef CONFIG_NET_CBUS
/* We must set the 8390 for word mode. */
outb_p(0x49, ioaddr + EN0_DCFG);
+#endif
start_page = NESM_START_PG;
stop_page = NESM_STOP_PG;
+#ifdef CONFIG_NE2K_CBUS_CNET98EL
+ if (hw->hwtype == NE2K_CBUS_HARDWARE_TYPE_CNET98EL) {
+ start_page = CNET98EL_START_PG;
+ stop_page = CNET98EL_STOP_PG;
+ }
+#endif
} else {
start_page = NE1SM_START_PG;
stop_page = NE1SM_STOP_PG;
}

neX000 = (SA_prom[14] == 0x57 && SA_prom[15] == 0x57);
+#ifndef CONFIG_NET_CBUS
ctron = (SA_prom[0] == 0x00 && SA_prom[1] == 0x00 && SA_prom[2] == 0x1d);
copam = (SA_prom[14] == 0x49 && SA_prom[15] == 0x00);

@@ -368,6 +612,11 @@
start_page = 0x01;
stop_page = (wordlength == 2) ? 0x40 : 0x20;
}
+#else
+ if (neX000) {
+ name = "C-Bus-NE2K-compat";
+ }
+#endif
else
{
#ifdef SUPPORT_NE_BAD_CLONES
@@ -414,10 +663,18 @@
dev->irq = probe_irq_off(cookie);
if (ei_debug > 2)
printk(" autoirq is %d\n", dev->irq);
- } else if (dev->irq == 2)
+ } else
+#ifndef CONFIG_X86_PC9800
+ if (dev->irq == 2)
/* Fixup for users that don't know that IRQ 2 is really IRQ 9,
or don't know which one to set. */
dev->irq = 9;
+#else
+ if (dev->irq == 7)
+ /* Fixup for users that don't know that IRQ 7 is really IRQ 11,
+ or don't know which one to set. */
+ dev->irq = 11;
+#endif

if (! dev->irq) {
printk(" failed to detect IRQ line.\n");
@@ -448,8 +705,13 @@
dev->dev_addr[i] = SA_prom[i];
}

+#ifndef CONFIG_NET_CBUS
printk("\n%s: %s found at %#x, using IRQ %d.\n",
dev->name, name, ioaddr, dev->irq);
+#else
+ printk("\n%s: %s found at %#x, hardware type %d(%s), using IRQ %d.\n",
+ dev->name, name, ioaddr, hw->hwtype, hw->hwident, dev->irq);
+#endif

ei_status.name = name;
ei_status.tx_start_page = start_page;
@@ -473,10 +735,23 @@
return 0;

err_out_kfree:
+#ifndef CONFIG_NET_CBUS
kfree(dev->priv);
dev->priv = NULL;
+#else
+ ne2k_cbus_destroy(dev);
+#endif
err_out:
+#ifndef CONFIG_NET_CBUS
release_region(ioaddr, NE_IO_EXTENT);
+#else
+ {
+ const struct ne2k_cbus_region *rlist;
+ for (rlist = hw->regionlist; rlist->range; rlist++) {
+ release_region(ioaddr + rlist->start, rlist->range);
+ }
+ }
+#endif
return ret;
}

@@ -500,10 +775,18 @@
static void ne_reset_8390(struct net_device *dev)
{
unsigned long reset_start_time = jiffies;
+#ifdef CONFIG_NET_CBUS
+ struct ei_device *ei_local = (struct ei_device *)(dev->priv);
+#endif

if (ei_debug > 1)
printk(KERN_DEBUG "resetting the 8390 t=%ld...", jiffies);

+#ifdef CONFIG_NET_CBUS
+ /* derived from CNET98EL-patch for bad clones... */
+ outb_p(E8390_NODMA | E8390_STOP, NE_BASE + E8390_CMD); /* 0x20 | 0x1 */
+#endif
+
/* DON'T change these to inb_p/outb_p or reset will fail on clones. */
outb(inb(NE_BASE + NE_RESET), NE_BASE + NE_RESET);

@@ -526,6 +809,9 @@
static void ne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page)
{
int nic_base = dev->base_addr;
+#ifdef CONFIG_NET_CBUS
+ struct ei_device *ei_local = (struct ei_device *)(dev->priv);
+#endif

/* This *shouldn't* happen. If it does, it's the last thing you'll see */

@@ -568,6 +854,9 @@
#endif
int nic_base = dev->base_addr;
char *buf = skb->data;
+#ifdef CONFIG_NET_CBUS
+ struct ei_device *ei_local = (struct ei_device *)(dev->priv);
+#endif

/* This *shouldn't* happen. If it does, it's the last thing you'll see */
if (ei_status.dmaing)
@@ -578,6 +867,12 @@
return;
}
ei_status.dmaing |= 0x01;
+
+#ifdef CONFIG_NET_CBUS
+ /* round up count to a word (derived from ICM-patch) */
+ count = (count + 1) & ~1;
+#endif
+
outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, nic_base+ NE_CMD);
outb_p(count & 0xff, nic_base + EN0_RCNTLO);
outb_p(count >> 8, nic_base + EN0_RCNTHI);
@@ -635,6 +930,9 @@
#ifdef NE_SANITY_CHECK
int retries = 0;
#endif
+#ifdef CONFIG_NET_CBUS
+ struct ei_device *ei_local = (struct ei_device *)(dev->priv);
+#endif

/* Round the count up for word writes. Do we need to do this?
What effect will an odd byte count have on the 8390?
@@ -738,13 +1036,22 @@
static int io[MAX_NE_CARDS];
static int irq[MAX_NE_CARDS];
static int bad[MAX_NE_CARDS]; /* 0xbad = bad sig or no reset ack */
+#ifdef CONFIG_NET_CBUS
+static int hwtype[MAX_NE_CARDS] = { 0, }; /* board type */
+#endif

MODULE_PARM(io, "1-" __MODULE_STRING(MAX_NE_CARDS) "i");
MODULE_PARM(irq, "1-" __MODULE_STRING(MAX_NE_CARDS) "i");
MODULE_PARM(bad, "1-" __MODULE_STRING(MAX_NE_CARDS) "i");
+#ifdef CONFIG_NET_CBUS
+MODULE_PARM(hwtype, "1-" __MODULE_STRING(MAX_NE_CARDS) "i");
+#endif
MODULE_PARM_DESC(io, "I/O base address(es),required");
MODULE_PARM_DESC(irq, "IRQ number(s)");
MODULE_PARM_DESC(bad, "Accept card(s) with bad signatures");
+#ifdef CONFIG_NET_CBUS
+MODULE_PARM_DESC(hwtype, "Board type of PC-9800 C-Bus NIC");
+#endif
MODULE_DESCRIPTION("NE1000/NE2000 ISA/PnP Ethernet driver");
MODULE_LICENSE("GPL");

@@ -762,6 +1069,9 @@
dev->irq = irq[this_dev];
dev->mem_end = bad[this_dev];
dev->base_addr = io[this_dev];
+#ifdef CONFIG_NET_CBUS
+ dev->mem_start = hwtype[this_dev];
+#endif
dev->init = ne_probe;
if (register_netdev(dev) == 0) {
found++;
@@ -791,9 +1101,23 @@
if (idev)
pnp_device_detach(idev);
free_irq(dev->irq, dev);
+#ifndef CONFIG_NET_CBUS
release_region(dev->base_addr, NE_IO_EXTENT);
+#else /* CONFIG_NET_CBUS */
+ {
+ const struct ne2k_cbus_hwinfo *hw = ne2k_cbus_get_hwinfo((int)(dev->mem_start & NE2K_CBUS_HARDWARE_TYPE_MASK));
+ const struct ne2k_cbus_region *rlist;
+ for (rlist = hw->regionlist; rlist->range; rlist++) {
+ release_region(dev->base_addr + rlist->start, rlist->range);
+ }
+ }
+#endif /* !CONFIG_NET_CBUS */
unregister_netdev(dev);
+#ifndef CONFIG_NET_CBUS
kfree(priv);
+#else
+ ne2k_cbus_destroy(dev);
+#endif
}
}
}
diff -Nru linux-2.5.50/drivers/net/ne2k_cbus.h linux98-2.5.50/drivers/net/ne2k_cbus.h
--- linux-2.5.42/drivers/net/ne2k_cbus.h 1970-01-01 09:00:00.000000000 +0900
+++ linux98-2.5.42/drivers/net/ne2k_cbus.h 2002-12-15 10:56:15.000000000 +0900
@@ -0,0 +1,481 @@
+/* ne2k_cbus.h:
+ vender-specific information definition for NEC PC-9800
+ C-bus Ethernet Cards
+ Used in ne.c
+
+ (C)1998,1999 KITAGWA Takurou & Linux/98 project
+*/
+
+#include <linux/config.h>
+
+#undef NE_RESET
+#define NE_RESET EI_SHIFT(0x11) /* Issue a read to reset, a write to clear. */
+
+#ifdef CONFIG_NE2K_CBUS_CNET98EL
+#ifndef CONFIG_NE2K_CBUS_CNET98EL_IO_BASE
+#warning CONFIG_NE2K_CBUS_CNET98EL_IO_BASE is not defined(config error?)
+#warning use 0xaaed as default
+#define CONFIG_NE2K_CBUS_CNET98EL_IO_BASE 0xaaed /* or 0x55ed */
+#endif
+#define CNET98EL_START_PG 0x00
+#define CNET98EL_STOP_PG 0x40
+#endif
+
+/* Hardware type definition (derived from *BSD) */
+#define NE2K_CBUS_HARDWARE_TYPE_MASK 0xff
+
+/* 0: reserved for auto-detect */
+/* 1: (not tested)
+ Allied Telesis CentreCom LA-98-T */
+#define NE2K_CBUS_HARDWARE_TYPE_ATLA98 1
+/* 2: (not tested)
+ ELECOM Laneed
+ LD-BDN[123]A
+ PLANET SMART COM 98 EN-2298-C
+ MACNICA ME98 */
+#define NE2K_CBUS_HARDWARE_TYPE_BDN 2
+/* 3:
+ Melco EGY-98
+ Contec C-NET(98)E*A/L*A,C-NET(98)P */
+#define NE2K_CBUS_HARDWARE_TYPE_EGY98 3
+/* 4:
+ Melco LGY-98,IND-SP,IND-SS
+ MACNICA NE2098 */
+#define NE2K_CBUS_HARDWARE_TYPE_LGY98 4
+/* 5:
+ ICM DT-ET-25,DT-ET-T5,IF-2766ET,IF-2771ET
+ PLANET SMART COM 98 EN-2298-T,EN-2298P-T
+ D-Link DE-298PT,DE-298PCAT
+ ELECOM Laneed LD-98P */
+#define NE2K_CBUS_HARDWARE_TYPE_ICM 5
+/* 6: (reserved for SIC-98, which is not supported in this driver.) */
+/* 7: (unused in *BSD?)
+ <Original NE2000 compatible>
+ <for PCI/PCMCIA cards>
+*/
+#define NE2K_CBUS_HARDWARE_TYPE_NE2K 7
+/* 8:
+ NEC PC-9801-108 */
+#define NE2K_CBUS_HARDWARE_TYPE_NEC108 8
+/* 9:
+ I-O DATA LA-98,LA/T-98 */
+#define NE2K_CBUS_HARDWARE_TYPE_IOLA98 9
+/* 10: (reserved for C-NET(98), which is not supported in this driver.) */
+/* 11:
+ Contec C-NET(98)E,L */
+#define NE2K_CBUS_HARDWARE_TYPE_CNET98EL 11
+
+#define NE2K_CBUS_HARDWARE_TYPE_MAX 11
+
+/* HARDWARE TYPE ID 12-31: reserved */
+
+struct ne2k_cbus_offsetinfo {
+ unsigned short skip;
+ unsigned short offset8; /* +0x8 - +0xf */
+ unsigned short offset10; /* +0x10 */
+ unsigned short offset1f; /* +0x1f */
+};
+
+struct ne2k_cbus_region {
+ unsigned short start;
+ short range;
+};
+
+struct ne2k_cbus_hwinfo {
+ const unsigned short hwtype;
+ const unsigned char *hwident;
+#ifndef MODULE
+ const unsigned short *portlist;
+#endif
+ const struct ne2k_cbus_offsetinfo *offsetinfo;
+ const struct ne2k_cbus_region *regionlist;
+};
+
+#ifdef CONFIG_NE2K_CBUS_ATLA98
+#ifndef MODULE
+static unsigned short atla98_portlist[] __initdata = {
+ 0xd0,
+ 0
+};
+#endif
+#define atla98_offsetinfo ne2k_offsetinfo
+#define atla98_regionlist ne2k_regionlist
+#endif /* CONFIG_NE2K_CBUS_ATLA98 */
+
+#ifdef CONFIG_NE2K_CBUS_BDN
+#ifndef MODULE
+static unsigned short bdn_portlist[] __initdata = {
+ 0xd0,
+ 0
+};
+#endif
+static struct ne2k_cbus_offsetinfo bdn_offsetinfo __initdata = {
+#if 0
+ /* comes from FreeBSD(98) ed98.h */
+ 0x1000, 0x8000, 0x100, 0xc200 /* ??? */
+#else
+ /* comes from NetBSD/pc98 if_ne_isa.c */
+ 0x1000, 0x8000, 0x100, 0x7f00 /* ??? */
+#endif
+};
+static struct ne2k_cbus_region bdn_regionlist[] __initdata = {
+ {0x0, 1}, {0x1000, 1}, {0x2000, 1}, {0x3000,1},
+ {0x4000, 1}, {0x5000, 1}, {0x6000, 1}, {0x7000, 1},
+ {0x8000, 1}, {0x9000, 1}, {0xa000, 1}, {0xb000, 1},
+ {0xc000, 1}, {0xd000, 1}, {0xe000, 1}, {0xf000, 1},
+ {0x100, 1}, {0x7f00, 1},
+ {0x0, 0}
+};
+#endif /* CONFIG_NE2K_CBUS_BDN */
+
+#ifdef CONFIG_NE2K_CBUS_EGY98
+#ifndef MODULE
+static unsigned short egy98_portlist[] __initdata = {
+ 0xd0,
+ 0
+};
+#endif
+static struct ne2k_cbus_offsetinfo egy98_offsetinfo __initdata = {
+ 0x02, 0x100, 0x200, 0x300
+};
+static struct ne2k_cbus_region egy98_regionlist[] __initdata = {
+ {0x0, 1}, {0x2, 1}, {0x4, 1}, {0x6, 1},
+ {0x8, 1}, {0xa, 1}, {0xc, 1}, {0xe, 1},
+ {0x100, 1}, {0x102, 1}, {0x104, 1}, {0x106, 1},
+ {0x108, 1}, {0x10a, 1}, {0x10c, 1}, {0x10e, 1},
+ {0x200, 1}, {0x300, 1},
+ {0x0, 0}
+};
+#endif /* CONFIG_NE2K_CBUS_EGY98 */
+
+#ifdef CONFIG_NE2K_CBUS_LGY98
+#ifndef MODULE
+static unsigned short lgy98_portlist[] __initdata = {
+ 0xd0, 0x10d0, 0x20d0, 0x30d0, 0x40d0, 0x50d0, 0x60d0, 0x70d0,
+ 0
+};
+#endif
+static struct ne2k_cbus_offsetinfo lgy98_offsetinfo __initdata = {
+ 0x01, 0x08, 0x200, 0x300
+};
+static struct ne2k_cbus_region lgy98_regionlist[] __initdata = {
+ {0x0, 16}, {0x200, 1}, {0x300, 1},
+ {0x0, 0}
+};
+#endif /* CONFIG_NE2K_CBUS_LGY98 */
+
+#ifdef CONFIG_NE2K_CBUS_ICM
+#ifndef MODULE
+static unsigned short icm_portlist[] __initdata = {
+ /* ICM */
+ 0x56d0,
+ /* LD-98PT */
+ 0x46d0, 0x66d0, 0x76d0, 0x86d0, 0x96d0, 0xa6d0, 0xb6d0, 0xc6d0,
+ 0
+};
+#endif
+static struct ne2k_cbus_offsetinfo icm_offsetinfo __initdata = {
+ 0x01, 0x08, 0x100, 0x10f
+};
+static struct ne2k_cbus_region icm_regionlist[] __initdata = {
+ {0x0, 16}, {0x100, 16},
+ {0x0, 0}
+};
+#endif /* CONFIG_NE2K_CBUS_ICM */
+
+#if defined(CONFIG_NE2K_CBUS_NE2K) && !defined(MODULE)
+static unsigned short ne2k_portlist[] __initdata = {
+ 0xd0, 0x300, 0x280, 0x320, 0x340, 0x360, 0x380,
+ 0
+};
+#endif
+#if defined(CONFIG_NE2K_CBUS_NE2K) || defined(CONFIG_NE2K_CBUS_ATLA98)
+static struct ne2k_cbus_offsetinfo ne2k_offsetinfo __initdata = {
+ 0x01, 0x08, 0x10, 0x1f
+};
+static struct ne2k_cbus_region ne2k_regionlist[] __initdata = {
+ {0x0, 32},
+ {0x0, 0}
+};
+#endif
+
+#ifdef CONFIG_NE2K_CBUS_NEC108
+#ifndef MODULE
+static unsigned short nec108_portlist[] __initdata = {
+ 0x770, 0x2770, 0x4770, 0x6770,
+ 0
+};
+#endif
+static struct ne2k_cbus_offsetinfo nec108_offsetinfo __initdata = {
+ 0x02, 0x1000, 0x888, 0x88a
+};
+static struct ne2k_cbus_region nec108_regionlist[] __initdata = {
+ {0x0, 1}, {0x2, 1}, {0x4, 1}, {0x6, 1},
+ {0x8, 1}, {0xa, 1}, {0xc, 1}, {0xe, 1},
+ {0x1000, 1}, {0x1002, 1}, {0x1004, 1}, {0x1006, 1},
+ {0x1008, 1}, {0x100a, 1}, {0x100c, 1}, {0x100e, 1},
+ {0x888, 1}, {0x88a, 1}, {0x88c, 1}, {0x88e, 1},
+ {0x0, 0}
+};
+#endif
+
+#ifdef CONFIG_NE2K_CBUS_IOLA98
+#ifndef MODULE
+static unsigned short iola98_portlist[] __initdata = {
+ 0xd0, 0xd2, 0xd4, 0xd6, 0xd8, 0xda, 0xdc, 0xde,
+ 0
+};
+#endif
+static struct ne2k_cbus_offsetinfo iola98_offsetinfo __initdata = {
+ 0x1000, 0x8000, 0x100, 0xf100
+};
+static struct ne2k_cbus_region iola98_regionlist[] __initdata = {
+ {0x0, 1}, {0x1000, 1}, {0x2000, 1}, {0x3000, 1},
+ {0x4000, 1}, {0x5000, 1}, {0x6000, 1}, {0x7000, 1},
+ {0x8000, 1}, {0x9000, 1}, {0xa000, 1}, {0xb000, 1},
+ {0xc000, 1}, {0xd000, 1}, {0xe000, 1}, {0xf000, 1},
+ {0x100, 1}, {0xf100, 1},
+ {0x0,0}
+};
+#endif /* CONFIG_NE2K_CBUS_IOLA98 */
+
+#ifdef CONFIG_NE2K_CBUS_CNET98EL
+#ifndef MODULE
+static unsigned short cnet98el_portlist[] __initdata = {
+ 0x3d0, 0x13d0, 0x23d0, 0x33d0, 0x43d0, 0x53d0, 0x60d0, 0x70d0,
+ 0
+};
+#endif
+static struct ne2k_cbus_offsetinfo cnet98el_offsetinfo __initdata = {
+ 0x01, 0x08, 0x40e, 0x400
+};
+static struct ne2k_cbus_region cnet98el_regionlist[] __initdata = {
+ {0x0, 16}, {0x400, 16},
+ {0x0, 0}
+};
+#endif
+
+
+/* port information table (for ne.c initialize/probe process) */
+
+static struct ne2k_cbus_hwinfo ne2k_cbus_hwinfo_list[] __initdata = {
+#ifdef CONFIG_NE2K_CBUS_ATLA98
+/* NOT TESTED */
+ {
+ NE2K_CBUS_HARDWARE_TYPE_ATLA98,
+ "LA-98-T",
+#ifndef MODULE
+ atla98_portlist,
+#endif
+ &atla98_offsetinfo, atla98_regionlist
+ },
+#endif
+#ifdef CONFIG_NE2K_CBUS_BDN
+/* NOT TESTED */
+ {
+ NE2K_CBUS_HARDWARE_TYPE_BDN,
+ "LD-BDN[123]A",
+#ifndef MODULE
+ bdn_portlist,
+#endif
+ &bdn_offsetinfo, bdn_regionlist
+ },
+#endif
+#ifdef CONFIG_NE2K_CBUS_ICM
+ {
+ NE2K_CBUS_HARDWARE_TYPE_ICM,
+ "IF-27xxET",
+#ifndef MODULE
+ icm_portlist,
+#endif
+ &icm_offsetinfo, icm_regionlist
+ },
+#endif
+#ifdef CONFIG_NE2K_CBUS_NE2K
+ {
+ NE2K_CBUS_HARDWARE_TYPE_NE2K,
+ "NE2000 compat.",
+#ifndef MODULE
+ ne2k_portlist,
+#endif
+ &ne2k_offsetinfo, ne2k_regionlist
+ },
+#endif
+#ifdef CONFIG_NE2K_CBUS_NEC108
+ {
+ NE2K_CBUS_HARDWARE_TYPE_NEC108,
+ "PC-9801-108",
+#ifndef MODULE
+ nec108_portlist,
+#endif
+ &nec108_offsetinfo, nec108_regionlist
+ },
+#endif
+#ifdef CONFIG_NE2K_CBUS_IOLA98
+ {
+ NE2K_CBUS_HARDWARE_TYPE_IOLA98,
+ "LA-98",
+#ifndef MODULE
+ iola98_portlist,
+#endif
+ &iola98_offsetinfo, iola98_regionlist
+ },
+#endif
+#ifdef CONFIG_NE2K_CBUS_CNET98EL
+ {
+ NE2K_CBUS_HARDWARE_TYPE_CNET98EL,
+ "C-NET(98)E/L",
+#ifndef MODULE
+ cnet98el_portlist,
+#endif
+ &cnet98el_offsetinfo, cnet98el_regionlist
+ },
+#endif
+/* NOTE: LGY98 must be probed before EGY98, or system stalled!? */
+#ifdef CONFIG_NE2K_CBUS_LGY98
+ {
+ NE2K_CBUS_HARDWARE_TYPE_LGY98,
+ "LGY-98",
+#ifndef MODULE
+ lgy98_portlist,
+#endif
+ &lgy98_offsetinfo, lgy98_regionlist
+ },
+#endif
+#ifdef CONFIG_NE2K_CBUS_EGY98
+ {
+ NE2K_CBUS_HARDWARE_TYPE_EGY98,
+ "EGY-98",
+#ifndef MODULE
+ egy98_portlist,
+#endif
+ &egy98_offsetinfo, egy98_regionlist
+ },
+#endif
+ {
+ 0,
+ "unsupported hardware",
+#ifndef MODULE
+ NULL,
+#endif
+ NULL, NULL
+ }
+};
+
+static int __init ne2k_cbus_init(struct net_device *dev)
+{
+ struct ei_device *ei_local;
+ if (dev->priv == NULL) {
+ ei_local = kmalloc(sizeof(struct ei_device), GFP_KERNEL);
+ if (ei_local == NULL)
+ return -ENOMEM;
+ memset(ei_local, 0, sizeof(struct ei_device));
+ ei_local->reg_offset = kmalloc(sizeof(typeof(*ei_local->reg_offset))*18, GFP_KERNEL);
+ if (ei_local->reg_offset == NULL) {
+ kfree(ei_local);
+ return -ENOMEM;
+ }
+ spin_lock_init(&ei_local->page_lock);
+ dev->priv = ei_local;
+ }
+ return 0;
+}
+
+static void ne2k_cbus_destroy(struct net_device *dev)
+{
+ struct ei_device *ei_local = (struct ei_device *)(dev->priv);
+ if (ei_local != NULL) {
+ if (ei_local->reg_offset)
+ kfree(ei_local->reg_offset);
+ kfree(dev->priv);
+ dev->priv = NULL;
+ }
+}
+
+static const struct ne2k_cbus_hwinfo * __init ne2k_cbus_get_hwinfo(int hwtype)
+{
+ const struct ne2k_cbus_hwinfo *hw;
+
+ for (hw = &ne2k_cbus_hwinfo_list[0]; hw->hwtype; hw++) {
+ if (hw->hwtype == hwtype) break;
+ }
+ return hw;
+}
+
+static void __init ne2k_cbus_set_hwtype(struct net_device *dev, const struct ne2k_cbus_hwinfo *hw, int ioaddr)
+{
+ struct ei_device *ei_local = (struct ei_device *)(dev->priv);
+ int i;
+ int hwtype_old = dev->mem_start & NE2K_CBUS_HARDWARE_TYPE_MASK;
+
+ if (!ei_local)
+ panic("Gieee! ei_local == NULL!! (from %p)",
+ __builtin_return_address(0));
+
+ dev->mem_start &= ~NE2K_CBUS_HARDWARE_TYPE_MASK;
+ dev->mem_start |= hw->hwtype & NE2K_CBUS_HARDWARE_TYPE_MASK;
+
+ if (ei_debug > 2) {
+ printk(KERN_DEBUG "hwtype changed: %d -> %d\n",hwtype_old,(int)(dev->mem_start & NE2K_CBUS_HARDWARE_TYPE_MASK));
+ }
+
+ if (hw->offsetinfo) {
+ for (i = 0; i < 8; i++) {
+ ei_local->reg_offset[i] = hw->offsetinfo->skip * i;
+ }
+ for (i = 8; i < 16; i++) {
+ ei_local->reg_offset[i] =
+ hw->offsetinfo->skip*(i-8) + hw->offsetinfo->offset8;
+ }
+#ifdef CONFIG_NE2K_CBUS_NEC108
+ if (hw->hwtype == NE2K_CBUS_HARDWARE_TYPE_NEC108) {
+ int adj = (ioaddr & 0xf000) /2;
+ ei_local->reg_offset[16] =
+ (hw->offsetinfo->offset10 | adj) - ioaddr;
+ ei_local->reg_offset[17] =
+ (hw->offsetinfo->offset1f | adj) - ioaddr;
+ } else {
+#endif /* CONFIG_NE2K_CBUS_NEC108 */
+ ei_local->reg_offset[16] = hw->offsetinfo->offset10;
+ ei_local->reg_offset[17] = hw->offsetinfo->offset1f;
+#ifdef CONFIG_NE2K_CBUS_NEC108
+ }
+#endif
+ } else {
+ /* make dummmy offset list */
+ for (i = 0; i < 16; i++) {
+ ei_local->reg_offset[i] = i;
+ }
+ ei_local->reg_offset[16] = 0x10;
+ ei_local->reg_offset[17] = 0x1f;
+ }
+}
+
+#if defined(CONFIG_NE2K_CBUS_ICM) || defined(CONFIG_NE2K_CBUS_CNET98EL)
+static void __init ne2k_cbus_readmem(struct net_device *dev, int ioaddr, unsigned short memaddr, char *buf, unsigned short len)
+{
+ struct ei_device *ei_local = (struct ei_device *)(dev->priv);
+ outb_p(E8390_NODMA | E8390_START, ioaddr+E8390_CMD);
+ outb_p(len & 0xff, ioaddr+EN0_RCNTLO);
+ outb_p(len >> 8, ioaddr+EN0_RCNTHI);
+ outb_p(memaddr & 0xff, ioaddr+EN0_RSARLO);
+ outb_p(memaddr >> 8, ioaddr+EN0_RSARHI);
+ outb_p(E8390_RREAD | E8390_START, ioaddr+E8390_CMD);
+ insw(ioaddr+NE_DATAPORT, buf, len >> 1);
+}
+static void __init ne2k_cbus_writemem(struct net_device *dev, int ioaddr, unsigned short memaddr, const char *buf, unsigned short len)
+{
+ struct ei_device *ei_local = (struct ei_device *)(dev->priv);
+ outb_p(E8390_NODMA | E8390_START, ioaddr+E8390_CMD);
+ outb_p(ENISR_RDC, ioaddr+EN0_ISR);
+ outb_p(len & 0xff, ioaddr+EN0_RCNTLO);
+ outb_p(len >> 8, ioaddr+EN0_RCNTHI);
+ outb_p(memaddr & 0xff, ioaddr+EN0_RSARLO);
+ outb_p(memaddr >> 8, ioaddr+EN0_RSARHI);
+ outb_p(E8390_RWRITE | E8390_START, ioaddr+E8390_CMD);
+ outsw(ioaddr+NE_DATAPORT, buf, len >> 1);
+}
+#endif
+
+static int ne_probe_cbus(struct net_device *dev, const struct ne2k_cbus_hwinfo *hw, int ioaddr);
+/* End of ne2k_cbus.h */
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2005-03-22 13:33    [W:0.201 / U:0.880 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site