lkml.org 
[lkml]   [2002]   [Sep]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: Linux hot swap support
Date
Thanks for the quick response. We are working on a new HW layout. I think
that I already got the answer to the critical question that I need. Once I
have the HW in place, I have to be sure that the 2.4.18-3 Kernel (or
greater) can support hot swap withoout any third party SW. Of course I
understand that my driver will have to be modified. This answer I already
received yesterday. Thanks very much.

Jack Bloch
Siemens ICN
phone (561) 923-6550
e-mail jack.bloch@icn.siemens.com


-----Original Message-----
From: Scott Murray [mailto:scottm@somanetworks.com]
Sent: Wednesday, September 18, 2002 8:06 PM
To: Bloch, Jack
Cc: Greg KH; Linux Kernel Mailing List
Subject: Re: Linux hot swap support


On Wed, 18 Sep 2002, Greg KH wrote:

> On Wed, Sep 18, 2002 at 05:37:50PM -0400, Bloch, Jack wrote:
> > At the moment, I only support removal. The way it works is as follows.
> >
> > Upon system start up my device driver detects all of the boards which
are
> > present (I support up to six). For each board it allocates the necessary
I/O
> > lists memory needed for operation. All addresses are then mapped to user
> > space with a mmap interface. Now, all HW is accessible from user space.
For
> > each device, an ISR is installed. As soon as the ejector handle for a
> > particular device is opened, the board (which is a Motorola 68060 based
> > board) issues an interrupt to me. I will shut this board down and
> > de-allocate any of the previously reserved resources. What is not so
easy is
> > to perform the insert. I thought about allocating memory becessary for a
> > maximum configuration, but I would still need to get the insertion
event.
> > But anyway since our device (even though it has multiple boards
internally)
> > is seen as a monolithic device from the main controlling host, the loss
of a
> > single board causes it to be taken out of service.
>
> Hm, you might want to take a look at the cPCI patches from Scott Murray,
> he has a solution for the resource and insertion problem that will
> probably work for you. You can find the patches on the pcihpd-discuss
> mailing list, and I think they were also posted to lkml in the past too.
> He's working on cleaning them up a bit for inclusion in the main kernel
> tree.

From looking at the datasheet of the AMCC S5935, it appears to not be
compliant with the PICMG 2.1 cPCI hotswap specification. That means
that it will probably take quite a bit of hardware and software hacking
to make insertion work. My patches should provide a bit of basis for
further hacking if you do want to try and build something yourself, but
if reliable hotplugging is important to your project, I'd suggest
considering a switch to a PCI controller or bridge that is PICMG 2.1
hotswap compliant.

Scott


--
Scott Murray
SOMA Networks, Inc.
Toronto, Ontario
e-mail: scottm@somanetworks.com



-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:29    [W:0.037 / U:1.612 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site