lkml.org 
[lkml]   [2002]   [Dec]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectATAPI DMA timeouts showing up in logs
Now that I've got the proper IDE driver in place (2.4.20rc4) and the master drive
on the primary interface is running at a full ATA133, these have started showing
up in the logs - 2 or 3 a day:

hdc: timeout waiting for DMA
ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hdc: status timeout: status=0xd0 { Busy }
hdc: drive not ready for command
hdc: ATAPI reset complete

Here's the dmesg output about this drive:

Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

VP_IDE: IDE controller on PCI bus 00 dev 89
PCI: No IRQ known for interrupt pin A of device 00:11.1.
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:DMA, hdd:pio
hda: Maxtor 6E030L0, ATA DISK drive
hdc: 56X CD-ROM, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c034b164, I/O limit 4095Mb (mask 0xffffffff)
hda: 60058656 sectors (30750 MB) w/2048KiB Cache, CHS=3738/255/63, UDMA(133)

hdc: ATAPI 52X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12

And /sbin/hdparm -I /dev/hdc

/dev/hdc:

ATAPI CD-ROM, with removable media
Model Number: 56X CD-ROM
Serial Number: MT1102A Firmware
Firmware Revision: VER 1.5F
Standards:
Used: ATAPI for CD-ROMs, SFF-8020i, r2.5
Supported: CD-ROM ATAPI-2
Configuration:
DRQ response: 50us.
Packet size: 12 bytes
Capabilities:
LBA, IORDY(cannot be disabled)
DMA: *mdma0 mdma1 mdma2 *udma0 udma1 udma2 (?)
Cycle time: min=120ns recommended=150ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=227ns IORDY flow control=120ns

And /sbin/hdparm -i /dev/hdc

/dev/hdc:

Model=56X CD-ROM, FwRev=VER 1.5F, SerialNo=MT1102A Firmware
Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=0kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
IORDY=yes, tPIO={min:227,w/IORDY:120}, tDMA={min:120,rec:150}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2
AdvancedPM=no

And finally,

/sbin/hdparm -v /dev/hdc

/dev/hdc:
HDIO_GET_MULTCOUNT failed: Invalid argument
IO_support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 1 (on)
keepsettings = 0 (off)
readonly = 1 (on)
readahead = 8 (on)
HDIO_GETGEO failed: Invalid argument

This last one is the only indication that something might be amiss - the two
instances of "invalid argument" Other than that, the drive appears to work just
fine.

What am I looking at?

DG

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:31    [W:0.029 / U:0.248 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site