Messages in this thread | | | Date | Tue, 28 Dec 1999 12:53:42 -0700 (MST) | From | Chris Shutters <> | Subject | 2.3.35pre6 boot failure, PCI problems |
| |
Hello all,
As the subject line says, 2.3.35pre6 will not boot on my machine. The boot process fails during PCI initialization. The last three lines printed on the screen are:
PCI: PCI BIOS revision 2.10 entry at 0xfbc8e PCI: Using configuration type 1 PCI: Probing PCI hardware
The system in question is a Dell Latitude CPi D266XT Laptop inserted into a docking station. It boots and works find under all 2.2.x kernel versions (up to and including 2.2.14pre14).
Here is the output of lspci -vvx:
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge (AGP disabled) (rev 02) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ Latency: 32 set Region 0: Memory at d0000000 (32-bit, prefetchable) 00: 86 80 92 71 06 01 00 a2 02 00 00 06 00 20 00 00 10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:02.0 VGA compatible controller: Neomagic Corporation NM2160 [MagicGraph 128XD] (rev 01) Subsystem: Unknown device 1028:0074 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 11 Region 0: Memory at e1000000 (32-bit, prefetchable) Region 1: Memory at fbe00000 (32-bit, non-prefetchable) Region 2: Memory at fbd00000 (32-bit, non-prefetchable) 00: c8 10 04 00 03 00 80 02 01 00 00 03 00 20 00 00 10: 08 00 00 e1 00 00 e0 fb 00 00 d0 fb 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 74 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 10 ff
00:03.0 CardBus bridge: Texas Instruments PCI1131 (rev 01) Subsystem: Unknown device 104c:ac15 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 set, cache line size 08 Interrupt: pin A routed to IRQ 0 Region 0: Memory at <ignored> (32-bit, non-prefetchable) Bus: primary=00, secondary=20, subordinate=22, sec-latency=176 BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0007 00: 4c 10 15 ac 07 00 00 02 01 00 07 06 08 20 82 00 10: 00 00 00 68 00 00 00 02 00 20 22 b0 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 c0 07 40: 4c 10 15 ac 07 00 00 02 01 00 07 06 08 20 82 00 50: 00 00 00 68 00 00 00 02 00 20 22 b0 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 c0 07
00:03.1 CardBus bridge: Texas Instruments PCI1131 (rev 01) Subsystem: Unknown device 104c:ac15 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 set, cache line size 08 Interrupt: pin B routed to IRQ 0 Region 0: Memory at <ignored> (32-bit, non-prefetchable) Bus: primary=00, secondary=23, subordinate=25, sec-latency=176 BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0007 00: 4c 10 15 ac 07 00 00 02 01 00 07 06 08 20 82 00 10: 00 10 00 68 00 00 00 02 00 23 25 b0 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 c0 07 40: 4c 10 15 ac 07 00 00 02 01 00 07 06 08 20 82 00 50: 00 10 00 68 00 00 00 02 00 23 25 b0 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 c0 07
00:07.0 Bridge: Intel Corporation 82371AB PIIX4 ISA (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 set 00: 86 80 10 71 0f 01 80 02 01 00 80 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 set Region 4: I/O ports at 0860 00: 86 80 11 71 05 00 80 02 01 80 01 01 00 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 61 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 set Interrupt: pin D routed to IRQ 11 Region 4: I/O ports at ece0 00: 86 80 12 71 05 00 80 02 01 00 03 0c 00 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: e1 ec 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 04 00 00
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 01) Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00: 86 80 13 71 03 00 80 02 01 00 80 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:11.0 PCI bridge: Intel Corporation 82380FB (rev 01) (prog-if 80) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 set, cache line size 08 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Prefetchable memory behind bridge: e2000000-e2ffffff BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- 00: 86 80 4b 12 87 01 00 04 01 80 04 06 08 20 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 00 00 00 00 24 20: 00 00 00 00 00 e2 f0 e2 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06 00
01:05.0 IDE interface: CMD Technology Inc PCI0646 (rev 03) (prog-if 8f) Subsystem: Unknown device 1095:0646 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 2 min, 4 max, 32 set Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at fcf8 Region 1: I/O ports at fcf0 Region 2: I/O ports at fce0 Region 3: I/O ports at fcd8 Region 4: I/O ports at fcc0 00: 95 10 46 06 05 00 80 02 03 8f 01 01 00 20 00 00 10: f9 fc 00 00 f1 fc 00 00 e1 fc 00 00 d9 fc 00 00 20: c1 fc 00 00 00 00 00 00 00 00 00 00 95 10 46 06 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 02 04
01:07.0 SCSI storage controller: Adaptec AIC-7860 (rev 03) Subsystem: Unknown device 9004:7860 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 4 min, 4 max, 32 set, cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at f800 Region 1: Memory at fdfff000 (32-bit, non-prefetchable) Capabilities: [dc] Power Management version 1 Flags: PMEClk- AuxPwr- DSI+ D1- D2- PME- Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 04 90 78 60 17 01 90 02 03 00 00 01 08 20 00 00 10: 01 f8 00 00 00 f0 ff fd 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 04 90 60 78 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 04 04
01:08.0 Ethernet controller: 3Com Corporation 3c905 100BaseTX [Boomerang] Subsystem: Unknown device 1028:0075 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 3 min, 8 max, 32 set Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at fc80 00: b7 10 50 90 07 01 00 02 00 00 00 02 00 20 00 00 10: 81 fc 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 75 00 30: 00 00 00 fe 00 00 00 00 00 00 00 00 0a 01 03 08
Here is the output of lspci -H1 -vvx
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge (AGP disabled) (rev 02) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ Latency: 32 set Region 0: Memory at d0000000 (32-bit, prefetchable) 00: 86 80 92 71 06 01 00 a2 02 00 00 06 00 20 00 00 10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:02.0 VGA compatible controller: Neomagic Corporation NM2160 [MagicGraph 128XD] (rev 01) Subsystem: Unknown device 1028:0074 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 11 Region 0: Memory at e1000000 (32-bit, prefetchable) Region 1: Memory at fbe00000 (32-bit, non-prefetchable) Region 2: Memory at fbd00000 (32-bit, non-prefetchable) 00: c8 10 04 00 03 00 80 02 01 00 00 03 00 20 00 00 10: 08 00 00 e1 00 00 e0 fb 00 00 d0 fb 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 74 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 10 ff
00:03.0 CardBus bridge: Texas Instruments PCI1131 (rev 01) Subsystem: Unknown device 104c:ac15 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 set, cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: Memory at 68000000 (32-bit, non-prefetchable) Bus: primary=00, secondary=20, subordinate=22, sec-latency=176 BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0007 00: 4c 10 15 ac 07 00 00 02 01 00 07 06 08 20 82 00 10: 00 00 00 68 00 00 00 02 00 20 22 b0 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 c0 07 40: 4c 10 15 ac 07 00 00 02 01 00 07 06 08 20 82 00 50: 00 00 00 68 00 00 00 02 00 20 22 b0 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 c0 07
00:03.1 CardBus bridge: Texas Instruments PCI1131 (rev 01) Subsystem: Unknown device 104c:ac15 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 set, cache line size 08 Interrupt: pin B routed to IRQ 11 Region 0: Memory at 68001000 (32-bit, non-prefetchable) Bus: primary=00, secondary=23, subordinate=25, sec-latency=176 BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0007 00: 4c 10 15 ac 07 00 00 02 01 00 07 06 08 20 82 00 10: 00 10 00 68 00 00 00 02 00 23 25 b0 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 c0 07 40: 4c 10 15 ac 07 00 00 02 01 00 07 06 08 20 82 00 50: 00 10 00 68 00 00 00 02 00 23 25 b0 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 c0 07
00:07.0 Bridge: Intel Corporation 82371AB PIIX4 ISA (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 set 00: 86 80 10 71 0f 01 80 02 01 00 80 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 set Region 4: I/O ports at 0860 00: 86 80 11 71 05 00 80 02 01 80 01 01 00 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 61 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 set Interrupt: pin D routed to IRQ 11 Region 4: I/O ports at ece0 00: 86 80 12 71 05 00 80 02 01 00 03 0c 00 20 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: e1 ec 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 04 00 00
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 01) Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00: 86 80 13 71 03 00 80 02 01 00 80 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:11.0 PCI bridge: Intel Corporation 82380FB (rev 01) (prog-if 80) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 set, cache line size 08 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Prefetchable memory behind bridge: e2000000-e2ffffff BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- 00: 86 80 4b 12 87 01 00 04 01 80 04 06 08 20 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 00 00 00 00 24 20: 00 00 00 00 00 e2 f0 e2 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06 00
01:05.0 IDE interface: CMD Technology Inc PCI0646 (rev 03) (prog-if 8f) Subsystem: Unknown device 1095:0646 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 2 min, 4 max, 32 set Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at fcf8 Region 1: I/O ports at fcf0 Region 2: I/O ports at fce0 Region 3: I/O ports at fcd8 Region 4: I/O ports at fcc0 00: 95 10 46 06 05 00 80 02 03 8f 01 01 00 20 00 00 10: f9 fc 00 00 f1 fc 00 00 e1 fc 00 00 d9 fc 00 00 20: c1 fc 00 00 00 00 00 00 00 00 00 00 95 10 46 06 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 02 04
01:07.0 SCSI storage controller: Adaptec AIC-7860 (rev 03) Subsystem: Unknown device 9004:7860 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 4 min, 4 max, 32 set, cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at f800 Region 1: Memory at fdfff000 (32-bit, non-prefetchable) Capabilities: [dc] Power Management version 1 Flags: PMEClk- AuxPwr- DSI+ D1- D2- PME- Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 04 90 78 60 17 01 90 02 03 00 00 01 08 20 00 00 10: 01 f8 00 00 00 f0 ff fd 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 04 90 60 78 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 04 04
01:08.0 Ethernet controller: 3Com Corporation 3c905 100BaseTX [Boomerang] Subsystem: Unknown device 1028:0075 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 3 min, 8 max, 32 set Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at fc80 00: b7 10 50 90 07 01 00 02 00 00 00 02 00 20 00 00 10: 81 fc 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 75 00 30: 00 00 00 fe 00 00 00 00 00 00 00 00 0a 01 03 08
Please let me know if anyone needs any further information from me about this boot problem -- I am more than willing to help!
Cheers,
Chris Shutters cshutters@dmwworldwide.com
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/
| |