lkml.org 
[lkml]   [2024]   [May]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[net-next PATCH] test: hsr: Extend the hsr_redbox.sh to have more SAN devices connected
Date
After this change the single SAN device (ns3eth1) is now replaced with
two SAN devices - respectively ns4eth1 and ns5eth1.

It is possible to extend this script to have more SAN devices connected
by adding them to ns3br1 bridge.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
---
tools/testing/selftests/net/hsr/hsr_redbox.sh | 71 +++++++++++++------
1 file changed, 49 insertions(+), 22 deletions(-)

diff --git a/tools/testing/selftests/net/hsr/hsr_redbox.sh b/tools/testing/selftests/net/hsr/hsr_redbox.sh
index db69be95ecb3..1f36785347c0 100755
--- a/tools/testing/selftests/net/hsr/hsr_redbox.sh
+++ b/tools/testing/selftests/net/hsr/hsr_redbox.sh
@@ -8,12 +8,19 @@ source ./hsr_common.sh
do_complete_ping_test()
{
echo "INFO: Initial validation ping (HSR-SAN/RedBox)."
- # Each node has to be able each one.
+ # Each node has to be able to reach each one.
do_ping "${ns1}" 100.64.0.2
do_ping "${ns2}" 100.64.0.1
- # Ping from SAN to hsr1 (via hsr2)
+ # Ping between SANs (test bridge)
+ do_ping "${ns4}" 100.64.0.51
+ do_ping "${ns5}" 100.64.0.41
+ # Ping from SANs to hsr1 (via hsr2) (and opposite)
do_ping "${ns3}" 100.64.0.1
do_ping "${ns1}" 100.64.0.3
+ do_ping "${ns1}" 100.64.0.41
+ do_ping "${ns4}" 100.64.0.1
+ do_ping "${ns1}" 100.64.0.51
+ do_ping "${ns5}" 100.64.0.1
stop_if_error "Initial validation failed."

# Wait for MGNT HSR frames being received and nodes being
@@ -23,8 +30,12 @@ do_complete_ping_test()
echo "INFO: Longer ping test (HSR-SAN/RedBox)."
# Ping from SAN to hsr1 (via hsr2)
do_ping_long "${ns3}" 100.64.0.1
- # Ping from hsr1 (via hsr2) to SAN
+ # Ping from hsr1 (via hsr2) to SANs (and opposite)
do_ping_long "${ns1}" 100.64.0.3
+ do_ping_long "${ns1}" 100.64.0.41
+ do_ping_long "${ns4}" 100.64.0.1
+ do_ping_long "${ns1}" 100.64.0.51
+ do_ping_long "${ns5}" 100.64.0.1
stop_if_error "Longer ping test failed."

echo "INFO: All good."
@@ -35,22 +46,26 @@ setup_hsr_interfaces()
local HSRv="$1"

echo "INFO: preparing interfaces for HSRv${HSRv} (HSR-SAN/RedBox)."
-
-# |NS1 |
-# | |
-# | /-- hsr1 --\ |
-# | ns1eth1 ns1eth2 |
-# |------------------------|
-# | |
-# | |
-# | |
-# |------------------------| |-----------|
-# | ns2eth1 ns2eth2 | | |
-# | \-- hsr2 --/ | | |
-# | \ | | |
-# | ns2eth3 |--------| ns3eth1 |
-# | (interlink)| | |
-# |NS2 (RedBOX) | |NS3 (SAN) |
+#
+# IPv4 addresses (100.64.X.Y/24), and [X.Y] is presented on below diagram:
+#
+#
+# |NS1 | |NS4 |
+# | [0.1] | | |
+# | /-- hsr1 --\ | | [0.41] |
+# | ns1eth1 ns1eth2 | | ns4eth1 (SAN) |
+# |------------------------| |-------------------|
+# | | |
+# | | |
+# | | |
+# |------------------------| |-------------------------------|
+# | ns2eth1 ns2eth2 | | ns3eth2 |
+# | \-- hsr2 --/ | | / |
+# | [0.2] \ | | / | |------------|
+# | ns2eth3 |---| ns3eth1 -- ns3br1 -- ns3eth3--|--| ns5eth1 |
+# | (interlink)| | [0.3] [0.11] | | [0.51] |
+# |NS2 (RedBOX) | |NS3 (BR) | | NS5 (SAN) |
+#
#
# Check if iproute2 supports adding interlink port to hsrX device
ip link help hsr | grep -q INTERLINK
@@ -59,7 +74,9 @@ setup_hsr_interfaces()
# Create interfaces for name spaces
ip link add ns1eth1 netns "${ns1}" type veth peer name ns2eth1 netns "${ns2}"
ip link add ns1eth2 netns "${ns1}" type veth peer name ns2eth2 netns "${ns2}"
- ip link add ns3eth1 netns "${ns3}" type veth peer name ns2eth3 netns "${ns2}"
+ ip link add ns2eth3 netns "${ns2}" type veth peer name ns3eth1 netns "${ns3}"
+ ip link add ns3eth2 netns "${ns3}" type veth peer name ns4eth1 netns "${ns4}"
+ ip link add ns3eth3 netns "${ns3}" type veth peer name ns5eth1 netns "${ns5}"

sleep 1

@@ -70,21 +87,31 @@ setup_hsr_interfaces()
ip -n "${ns2}" link set ns2eth2 up
ip -n "${ns2}" link set ns2eth3 up

- ip -n "${ns3}" link set ns3eth1 up
+ ip -n "${ns3}" link add name ns3br1 type bridge
+ ip -n "${ns3}" link set ns3br1 up
+ ip -n "${ns3}" link set ns3eth1 master ns3br1 up
+ ip -n "${ns3}" link set ns3eth2 master ns3br1 up
+ ip -n "${ns3}" link set ns3eth3 master ns3br1 up
+
+ ip -n "${ns4}" link set ns4eth1 up
+ ip -n "${ns5}" link set ns5eth1 up

ip -net "${ns1}" link add name hsr1 type hsr slave1 ns1eth1 slave2 ns1eth2 supervision 45 version ${HSRv} proto 0
ip -net "${ns2}" link add name hsr2 type hsr slave1 ns2eth1 slave2 ns2eth2 interlink ns2eth3 supervision 45 version ${HSRv} proto 0

ip -n "${ns1}" addr add 100.64.0.1/24 dev hsr1
ip -n "${ns2}" addr add 100.64.0.2/24 dev hsr2
+ ip -n "${ns3}" addr add 100.64.0.11/24 dev ns3br1
ip -n "${ns3}" addr add 100.64.0.3/24 dev ns3eth1
+ ip -n "${ns4}" addr add 100.64.0.41/24 dev ns4eth1
+ ip -n "${ns5}" addr add 100.64.0.51/24 dev ns5eth1

ip -n "${ns1}" link set hsr1 up
ip -n "${ns2}" link set hsr2 up
}

check_prerequisites
-setup_ns ns1 ns2 ns3
+setup_ns ns1 ns2 ns3 ns4 ns5

trap cleanup_all_ns EXIT

--
2.20.1

\
 
 \ /
  Last update: 2024-05-27 18:24    [W:4.583 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site