On Wed, 2 Sep 2026 11:15:56 +0200
Andreas Kemnade <andreas@kemnade.info> wrote:

> On Wed, 02 Sep 2026 10:30:02 +0200
> "Mathieu Dubois-Briand" <mathieu.dubois-briand@bootlin.com> wrote:
> 
> > On Wed Sep 2, 2026 at 8:26 AM CEST, Andreas Kemnade wrote:  
> > > Hi,
> > >
> > > this seems to produce on OMAP3 (DM3730), even with the init fix.
> > >
> > > [    0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff
> > > , max_idle_ns: 58327039986419 ns                                                
> > > [    0.000030] sched_clock: 32 bits at 33kHz, resolution 30517ns, wraps every 65
> > > 535999984741ns                                                                  
> > > [    0.013488] clk: failed to reparent gpt1_fck to omap_32k_fck: -22            
> > > [    0.019805] Failed to initialize '/ocp@68000000/target-module@48318000/timer@
> > > 0': -19                                                                         
> > >
> > > Regards,
> > > Andreas    
> > 
> > Hi Andreas,
> > 
> > That one will be a bit harder for me to debug, as I'm not sure I can
> > easily get this hardware. But looking at the device tree and the
> > reference manual, I suspect something is wrong in the omap3 device tree.
> > 
> > In omap3.dtsi, we have this node [1]:
> > 
> > &timer1_target {
> > 	ti,no-reset-on-init;
> > 	ti,no-idle;
> > 	timer@0 {
> > 		assigned-clocks = <&gpt1_fck>;
> > 		assigned-clock-parents = <&omap_32k_fck>;
> > 	};
> > };
> > 
> > I suspect that's the source of the error: __set_clk_parents() in
> > drivers/clk/clk-conf.c will try to set &omap_32k_fck as a parent of
> > &gpt1_fck. But looking at omap3xxx-clocks.dtsi [2], &omap_32k_fck is not
> > a valid parent:
> > 
> > 	gpt1_fck: gpt1_fck {
> > 		#clock-cells = <0>;
> > 		compatible = "ti,composite-clock";
> > 		clocks = <&gpt1_gate_fck>, <&gpt1_mux_fck>;
> > 	};
> > 
> the composite clock is meant to combine the two clocks into one,
> so you have one single clock with enable/disable functions and
> parents. At least that seems to be the idea.
> 
> If the system fully boots, you see:
> localhost:/sys/kernel/debug/clk/gpt1_fck# cat clk_possible_parents 
> omap_32k_fck sys_ck
> 
> > Yet the &gpt1_mux_fck is a mux, and one of the parent is indeed
> > &omap_32k_fck [3]. So I suspect the correct assigned clock parent in
> > timer@0 should be &gpt1_mux_fck.
> > 
> > Can you try it that way?
> > 
> [    0.000000] OMAP clocksource: 32k_counter at 32768 Hz                        
> [    0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xfffffffs
> [    0.000000] sched_clock: 32 bits at 33kHz, resolution 30517ns, wraps every 6s
> [    0.013458] dmtimer_systimer_setup: clock source init failed: -517           
> 
> The system does not boot much further.
> 
I got this a bit further by fully replacing this composite clock.
With the system having a system timer, it boots till login prompt.
But:

[   32.069946] omap_dm_timer_set_source: failed to set timer_32k_ck as parent
[   32.094116] omap-dmtimer-pwm pwm-11: invalid pmtimer fclk rate
[   32.094146] pwm-backlight backlight: error -EINVAL: failed to apply initial PWM state
[   32.094177] pwm-backlight backlight: probe with driver pwm-backlight failed with error -22

This clock comes from here:
clk/ti/clk-3xxx.c:	DT_CLK(NULL, "timer_32k_ck", "omap_32k_fck"),

So same pattern. A composite clock cannot get its parent because there
is the expection that such behave like a combined clock made from mux + gate clock.


I have not found out if the early registration stuff in timer-ti-dm-systimer.c
is part of the mess. OMAP4 devicetrees I use, use assigned-clock-parents in
combination with ti,clkctrl clocks. That seems to work.

Regards,
Andreas