On 1/9/2026 4:03 AM, Daniel Golle wrote:
> Turns out that register address RTL_VND2_PHYSR (0xa434) maps to
> Clause-22 register MII_RESV2. Use that to get rid of yet another magic
> number, and rename access macros accordingly.
> 

RTL_VND2_PHYSR is documented in the datasheet, at least for RTL8221B(I)-VB-CG.
(this datasheet is publicly available, I don't have access to other datasheets)
MII_RESV2 isn't documented there. Is MII_RESV2 documented in any other datasheet?

> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
> ---
>  drivers/net/phy/realtek/realtek_main.c | 24 ++++++++++++------------
>  1 file changed, 12 insertions(+), 12 deletions(-)
> 
> diff --git a/drivers/net/phy/realtek/realtek_main.c b/drivers/net/phy/realtek/realtek_main.c
> index d07d60bc1ce34..5712372c71f91 100644
> --- a/drivers/net/phy/realtek/realtek_main.c
> +++ b/drivers/net/phy/realtek/realtek_main.c
> @@ -178,12 +178,12 @@
>  #define RTL9000A_GINMR				0x14
>  #define RTL9000A_GINMR_LINK_STATUS		BIT(4)
> 
> -#define RTL_VND2_PHYSR				0xa434
> -#define RTL_VND2_PHYSR_DUPLEX			BIT(3)
> -#define RTL_VND2_PHYSR_SPEEDL			GENMASK(5, 4)
> -#define RTL_VND2_PHYSR_SPEEDH			GENMASK(10, 9)
> -#define RTL_VND2_PHYSR_MASTER			BIT(11)
> -#define RTL_VND2_PHYSR_SPEED_MASK		(RTL_VND2_PHYSR_SPEEDL | RTL_VND2_PHYSR_SPEEDH)
> +#define RTL_PHYSR				MII_RESV2
> +#define RTL_PHYSR_DUPLEX			BIT(3)
> +#define RTL_PHYSR_SPEEDL			GENMASK(5, 4)
> +#define RTL_PHYSR_SPEEDH			GENMASK(10, 9)
> +#define RTL_PHYSR_MASTER			BIT(11)
> +#define RTL_PHYSR_SPEED_MASK			(RTL_PHYSR_SPEEDL | RTL_PHYSR_SPEEDH)
> 
>  #define	RTL_MDIO_PCS_EEE_ABLE			0xa5c4
>  #define	RTL_MDIO_AN_EEE_ADV			0xa5d0
> @@ -1102,12 +1102,12 @@ static void rtlgen_decode_physr(struct phy_device *phydev, int val)
>  	 * 0: Half Duplex
>  	 * 1: Full Duplex
>  	 */
> -	if (val & RTL_VND2_PHYSR_DUPLEX)
> +	if (val & RTL_PHYSR_DUPLEX)
>  		phydev->duplex = DUPLEX_FULL;
>  	else
>  		phydev->duplex = DUPLEX_HALF;
> 
> -	switch (val & RTL_VND2_PHYSR_SPEED_MASK) {
> +	switch (val & RTL_PHYSR_SPEED_MASK) {
>  	case 0x0000:
>  		phydev->speed = SPEED_10;
>  		break;
> @@ -1135,7 +1135,7 @@ static void rtlgen_decode_physr(struct phy_device *phydev, int val)
>  	 * 1: Master Mode
>  	 */
>  	if (phydev->speed >= 1000) {
> -		if (val & RTL_VND2_PHYSR_MASTER)
> +		if (val & RTL_PHYSR_MASTER)
>  			phydev->master_slave_state = MASTER_SLAVE_STATE_MASTER;
>  		else
>  			phydev->master_slave_state = MASTER_SLAVE_STATE_SLAVE;
> @@ -1155,8 +1155,7 @@ static int rtlgen_read_status(struct phy_device *phydev)
>  	if (!phydev->link)
>  		return 0;
> 
> -	val = phy_read_paged(phydev, RTL822X_VND2_TO_PAGE(RTL_VND2_PHYSR),
> -			     RTL822X_VND2_TO_PAGE_REG(RTL_VND2_PHYSR));
> +	val = phy_read(phydev, RTL_PHYSR);
>  	if (val < 0)
>  		return val;
> 
> @@ -1622,7 +1621,8 @@ static int rtl822x_c45_read_status(struct phy_device *phydev)
>  	}
> 
>  	/* Read actual speed from vendor register. */
> -	val = phy_read_mmd(phydev, MDIO_MMD_VEND2, RTL_VND2_PHYSR);
> +	val = phy_read_mmd(phydev, MDIO_MMD_VEND2,
> +			   RTL822X_VND2_C22_REG(RTL_PHYSR));
>  	if (val < 0)
>  		return val;
>