On Tue, Nov 25, 2025 at 10:50:59AM +0100, Krzysztof Kozlowski wrote:
> On Mon, Nov 24, 2025 at 10:18:00AM +0100, Jorge Marques wrote:
Hi Krzysztof,
> > Add dt-bindings for AD4062 family, devices AD4060/AD4062, low-power with
> > monitor capabilities SAR ADCs. Each variant of the family differs in
> > resolution. The device contains two outputs (gp0, gp1). The outputs can
> > be configured for range of options, such as threshold and data ready.
> > The device uses a 2-wire I3C interface.
> > 
> > Signed-off-by: Jorge Marques <jorge.marques@analog.com>
> > ---
> >  .../devicetree/bindings/iio/adc/adi,ad4062.yaml    | 123 +++++++++++++++++++++
> >  MAINTAINERS                                        |   6 +
> >  2 files changed, 129 insertions(+)
> > 
> > diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad4062.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad4062.yaml
> > new file mode 100644
> > index 0000000000000..a25af66dd64d2
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad4062.yaml
> > @@ -0,0 +1,123 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +# Copyright 2024 Analog Devices Inc.
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/iio/adc/adi,ad4062.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Analog Devices AD4062 ADC family device driver
> > +
> > +maintainers:
> > +  - Jorge Marques <jorge.marques@analog.com>
> > +
> > +description: |
> > +  Analog Devices AD4062 Single Channel Precision SAR ADC family
> > +
> > +  https://www.analog.com/media/en/technical-documentation/data-sheets/ad4060.pdf
> > +  https://www.analog.com/media/en/technical-documentation/data-sheets/ad4062.pdf
> > +
> > +properties:
> > +  compatible:
> > +    enum:
> > +      - adi,ad4060
> > +      - adi,ad4062
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  interrupts:
> > +    description:
> > +      The interrupt pins are digital outputs that can be configured at runtime
> > +      as multiple interrupt signals. Each can be configured as GP_INTR, RDY,
> > +      DEV_EN, logic low, logic high and DEV_RDY (GP1 only). RDY is the
> > +      active-low data ready signal, indicates when new ADC data are ready to
> > +      read. DEV_EN synchronizes the enable and power-down states of signal
> > +      chain devices with the ADC sampling instant. DEV_RDY is an active-high
> > +      signal that indicates when the device is ready to accept serial interface
> > +      communications. In GP_INTR mode, the interrupt outputs one of the
> > +      threshold detection interrupt signals (MIN_INTR, MAX_INTR or either).
> > +    minItems: 1
> 
> So the wire/pin can be physically disconnected?
> 
Yes, the device can yield those interrupts as through I3C
In-Band-Interrupts (IBI), which are messages sent in the I3C bus by the
target (this device). I consider as a fallback, because the overhead for
those bus interrupts are much higher. The user can have all interrupts
as IBIs, and re-use the pins as generic GPOs.
> > +    items:
> > +      - description:
> > +          gp0, interrupt line for GP0 pin, cannot be configured as DEV_RDY.
> 
> Write concise statements - duplicating gp0 is not helping. "GP0 pin,
> cannot be configured as DEV_RDY."
> 
> "GP1 pin, can be configured to any setting."
> 
> 
Ok
> > +      - description:
> > +          gp1, interrupt line for GP1 pin, can be configured to any setting.
> > +
> > +  interrupt-names:
> 
> Why this is not matching interrupts in number of items?
> 
Is missing

    minItems: 1

thanks,
> > +    items:
> > +      - const: gp0
> > +      - const: gp1
> > +
> > +  gpio-controller:
> > +    description:
> > +      Marks the device node as a GPIO controller. GPs not listed in
> > +      interrupt-names are exposed as a GPO.
> 
> "not listed as interrupts are..."
> 
Ack.
> > +
> > +  '#gpio-cells':
> > +    const: 2
> > +    description:
> > +      The first cell is the GPIO number and the second cell specifies
> > +      GPIO flags, as defined in <dt-bindings/gpio/gpio.h>.
> 
> Best regards,
> Krzysztof
> 

Best regards,
Jorge