lkml.org 
[lkml]   [2024]   [Apr]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v18 10/11] PCI/DPC: Add Error Disconnect Recover (EDR) support
From

On 4/11/24 11:07 AM, Bjorn Helgaas wrote:
> On Mon, Mar 23, 2020 at 05:26:07PM -0700, sathyanarayanan.kuppuswamy@linux.intel.com wrote:
>> From: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
>>
>> Error Disconnect Recover (EDR) is a feature that allows ACPI firmware to
>> notify OSPM that a device has been disconnected due to an error condition
>> (ACPI v6.3, sec 5.6.6). OSPM advertises its support for EDR on PCI devices
>> via _OSC (see [1], sec 4.5.1, table 4-4). The OSPM EDR notify handler
>> should invalidate software state associated with disconnected devices and
>> may attempt to recover them. OSPM communicates the status of recovery to
>> the firmware via _OST (sec 6.3.5.2).
>>
>> For PCIe, firmware may use Downstream Port Containment (DPC) to support
>> EDR. Per [1], sec 4.5.1, table 4-6, even if firmware has retained control
>> of DPC, OSPM may read/write DPC control and status registers during the EDR
>> notification processing window, i.e., from the time it receives an EDR
>> notification until it clears the DPC Trigger Status.
>>
>> Note that per [1], sec 4.5.1 and 4.5.2.4,
>>
>> 1. If the OS supports EDR, it should advertise that to firmware by
>> setting OSC_PCI_EDR_SUPPORT in _OSC Support.
>>
>> 2. If the OS sets OSC_PCI_EXPRESS_DPC_CONTROL in _OSC Control to request
>> control of the DPC capability, it must also set OSC_PCI_EDR_SUPPORT in
>> _OSC Support.
>>
>> Add an EDR notify handler to attempt recovery.
>>
>> [1] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
>> affecting PCI Firmware Specification, Rev. 3.2
>> https://members.pcisig.com/wg/PCI-SIG/document/12888
>> +static int acpi_enable_dpc(struct pci_dev *pdev)
>> +{
>> + struct acpi_device *adev = ACPI_COMPANION(&pdev->dev);
>> + union acpi_object *obj, argv4, req;
>> + int status;
>> +
>> + /*
>> + * Some firmware implementations will return default values for
>> + * unsupported _DSM calls. So checking acpi_evaluate_dsm() return
>> + * value for NULL condition is not a complete method for finding
>> + * whether given _DSM function is supported or not. So use
>> + * explicit func 0 call to find whether given _DSM function is
>> + * supported or not.
>> + */
>> + status = acpi_check_dsm(adev->handle, &pci_acpi_dsm_guid, 5,
>> + 1ULL << EDR_PORT_DPC_ENABLE_DSM);
>> + if (!status)
>> + return 0;
>> +
>> + status = 0;
>> + req.type = ACPI_TYPE_INTEGER;
>> + req.integer.value = 1;
>> +
>> + argv4.type = ACPI_TYPE_PACKAGE;
>> + argv4.package.count = 1;
>> + argv4.package.elements = &req;
>> +
>> + /*
>> + * Per Downstream Port Containment Related Enhancements ECN to PCI
>> + * Firmware Specification r3.2, sec 4.6.12, EDR_PORT_DPC_ENABLE_DSM is
>> + * optional. Return success if it's not implemented.
>> + */
>> + obj = acpi_evaluate_dsm(adev->handle, &pci_acpi_dsm_guid, 5,
>> + EDR_PORT_DPC_ENABLE_DSM, &argv4);
> This has been upstream for a while, just a follow-up question: this
> _DSM function was defined by the ECN with Rev 5. The ECN was
> incorporated into the PCI Firmware spec r3.3 with slightly different
> behavior as Rev 6.
>
> The main differences are:
>
> ECN
> - Rev 5
> - Arg3 is an Integer
> - Return is 0 (DPC disabled) or 1 (DPC enabled)
>
> r3.3 spec
> - Rev 6
> - Arg3 is a Package of one Integer
> - Return is 0 (DPC disabled, Hot-Plug Surprise may be set), 1 (DPC
> enabled, Hot-Plug Surprise may be cleared), or 2 (failure)
>
> So the question is whether this actually implements Rev 5 or Rev 6?
> It looks like this builds a *package* for Arg3 (which would correspond
> to Rev 6), but we're evaluating Rev 5, which specified an Integer.
>
> The meaning of the Arg3 values is basically the same, so I don't see
> an issue there, but it looks like if a platform implemented Rev 5
> according to the ECN to take a bare Integer, this might not work
> correctly.

I think it implements rev 6. The version number needs to be updated.

If you would like, I can submit a patch to fix it.

>
>> + if (!obj)
>> + return 0;
>> +
>> + if (obj->type != ACPI_TYPE_INTEGER) {
>> + pci_err(pdev, FW_BUG "Enable DPC _DSM returned non integer\n");
>> + status = -EIO;
>> + }
>> +
>> + if (obj->integer.value != 1) {
>> + pci_err(pdev, "Enable DPC _DSM failed to enable DPC\n");
>> + status = -EIO;
>> + }
>> +
>> + ACPI_FREE(obj);
>> +
>> + return status;
>> +}

--
Sathyanarayanan Kuppuswamy
Linux Kernel Developer


\
 
 \ /
  Last update: 2024-04-11 21:16    [W:0.281 / U:0.132 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site