Messages in this thread | | | From | Dimitri Fedrau <> | Subject | [PATCH v7 net-next 00/14] net: phy: marvell-88q2xxx: add driver for the Marvell 88Q2220 PHY | Date | Sun, 18 Feb 2024 08:57:37 +0100 |
| |
Changes in v2: - used defines MDIO_CTRL1_LPOWER and MDIO_PMA_CTRL1_SPEED1000 in mv88q222x_config_aneg_preinit - use genphy_c45_loopback - mv88q2xxx_read_status reads speed, master or slave state when autonegotiation is enabled - added defines for magic values in mv88q222x_get_sqi
Changes in v3: - mv88q2xxx_read_status includes autonegotiation case - add support for 100BT1 and 1000BT1 linkmode advertisement - use mv88q2xxx_get_sqi and mv88q2xxx_get_sqi_max, remove mv88q222x_get_sqi and mv88q222x_get_sqi_max - fix typo: rename mv88q2xxxx_get_sqi and mv88q2xxxx_get_sqi_max to mv88q2xxx_get_sqi and mv88q2xxx_get_sqi - add define MDIO_MMD_PCS_MV_RX_STAT for magic value 0x8230, documented in latest datasheets for both PHYs
Changes in V4: - clean up init sequence - separate patch for fixing typos in upstreamed code
Changes in V5: - add missing statics for mv88q222x_revb0_init_seq0 and mv88q222x_revb0_init_seq1 - fix typo in commit message: autonegotiation - fix ordering of Signed-off-by and Reviewed-by in commit messages - add interrupt support for link detection - add suspend / resume ops - add support for internal temperature sensor - add cable test support - call .soft_reset in mv88q2xxx_config_aneg, this makes mv88q2xxx_config_aneg compatible for Marvell88Q222x devices and remove mv88q222x_config_aneg which is then just duplicated code - cleanup mv88q2xxx_config_init and make it compatible with Marvell88Q222x devices - move parts from mv88q222x_config_init to mv88q2xxx_config_init that are applicable for all Marvell88Q2xxx devices.
Changes in V6: - add copyright and where the code is derived from (patch 5). Sorry Andrew. It is already reviewed, but I think it is the right place. Didn't remove the Reviewed-by because the changes doesn't touch any code that is getting executed. - add HWMON dependeny in Kconfig (patch 8) - use IS_ENABLED(CONFIG_HWMON) instead of ifdef CONFIG_HWMON to support hwmon built as module (patch 8) - drop shift constant MDIO_MMD_PCS_MV_TEMP_SENSOR3_INT_THRESH_SHIFT and use FIELD_GET and FIELD_PREP instead(patch 8) - drop shift constant MDIO_MMD_PCS_MV_TDR_STATUS_DIST_SHIFT and use FIELD_GET and FIELD_PREP instead (patch 9) - split previous patch 13 into two patches.
Changes in V7: - Check if cable test id done, rather than checking if test is in progress
Dimitri Fedrau (14): net: phy: Add BaseT1 auto-negotiation constants net: phy: Support 100/1000BT1 linkmode advertisements net: phy: c45: detect 100/1000BASE-T1 linkmode advertisements net: phy: marvell-88q2xxx: fix typos net: phy: marvell-88q2xxx: add driver for the Marvell 88Q2220 PHY net: phy: marvell-88q2xxx: add interrupt support for link detection net: phy: marvell-88q2xxx: add suspend / resume ops net: phy: marvell-88q2xxx: add support for temperature sensor net: phy: marvell-88q2xxx: add cable test support net: phy: marvell-88q2xxx: make mv88q2xxx_config_aneg generic net: phy: marvell-88q2xxx: switch to mv88q2xxx_config_aneg net: phy: marvell-88q2xxx: cleanup mv88q2xxx_config_init net: phy: marvell-88q2xxx: remove duplicated assignment of pma_extable net: phy: marvell-88q2xxx: move interrupt configuration
drivers/net/phy/Kconfig | 1 + drivers/net/phy/marvell-88q2xxx.c | 640 ++++++++++++++++++++++++++++-- drivers/net/phy/phy-c45.c | 3 +- include/linux/marvell_phy.h | 1 + include/linux/mdio.h | 8 + include/uapi/linux/mdio.h | 2 + 6 files changed, 625 insertions(+), 30 deletions(-)
-- 2.39.2
| |