lkml.org 
[lkml]   [2024]   [Jan]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v1 6/8] ARM: dts: aspeed: System1: GPIO, Fan ctrl, Led
From
Hello Krzysztof,

On 12/12/23 14:25, Krzysztof Kozlowski wrote:
> On 12/12/2023 17:40, Ninad Palsule wrote:
>> This commit adds following devices to the device tree.
>> - GPIO pin assignements, GPIO expansion devices
>> - LED brinker devices
>> - Fan controllers
>>
>> Tested:
>> This board is tested using the simics simulator.
>>
>> Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
>> ---
>> .../dts/aspeed/aspeed-bmc-ibm-system1.dts | 547 +++++++++++++++++-
> Squash it.

Yes, I made a single commit for device tree.

>
>> 1 file changed, 542 insertions(+), 5 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts
>> index b8e7e52d4600..75562aa63701 100644
>> --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts
>> +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts
>> @@ -114,6 +114,99 @@ vga_memory: region@bf000000 {
>> };
>> };
>>
>> + leds {
>> + compatible = "gpio-leds";
>> +
>> + bmc-ready {
> It does not look like you tested the DTS against bindings. Please run
> `make dtbs_check W=1` (see
> Documentation/devicetree/bindings/writing-schema.rst or
> https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
> for instructions).
Fixed names.
>
>> + gpios = <&gpio0 ASPEED_GPIO(L, 7) GPIO_ACTIVE_HIGH>;
>> + };
>> +
>> + bmc-hb {
> None of these were tested.
Fixed names
>
>> /*A0-A7*/ "","","","","","","","",
>> - /*B0-B7*/ "","","","","","","","",
>> + /*B0-B7*/ "","","","","bmc-tpm-reset","","","",
> Really? You just added these lines. There is no point in adding a new
> line and immediately changing it.
>
> This points how your split is artificial and not helpful.
> ...
Now I have a single commit for device tree.
>
>
>> &i2c2 {
>> @@ -486,6 +744,20 @@ regulator@43 {
>> &i2c6 {
>> status = "okay";
>>
>> + fan-controller@52 {
>> + compatible = "maxim,max31785a";
>> + reg = <0x52>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
> Why do you need cells?
Removed cells.
>
>> + };
>> +
>> + fan-controller@54 {
>> + compatible = "maxim,max31785a";
>> + reg = <0x54>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
> Why do you need cells?
Removed cells.
>
>> + };
>> +
>> i2c-mux@70 {
>> compatible = "nxp,pca9548";
>> reg = <0x70>;
>> @@ -522,6 +794,48 @@ i2c6mux0chn4: i2c@4 {
>> #address-cells = <1>;
>> #size-cells = <0>;
>> reg = <4>;
>> +
>> + led-controller@60 {
>> + compatible = "nxp,pca9551";
>> + reg = <0x60>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> +
>> + led@0 {
>> + label = "enclosure-id-led";
>> + reg = <0>;
>> + retain-state-shutdown;
>> + default-state = "keep";
>> + type = <PCA955X_TYPE_LED>;
>> + };
>> +
>> + led@1 {
>> + label = "attention-led";
>> + reg = <1>;
>> + retain-state-shutdown;
>> + default-state = "keep";
>> + type = <PCA955X_TYPE_LED>;
>> + };
>> +
>> + led@2 {
>> + label = "enclosure-fault-rollup-led";
>> + reg = <2>;
>> + retain-state-shutdown;
>> + default-state = "keep";
>> + type = <PCA955X_TYPE_LED>;
>> + };
>> +
>> + led@3 {
>> + label = "power-on-led";
>> + reg = <3>;
>> + retain-state-shutdown;
>> + default-state = "keep";
>> + type = <PCA955X_TYPE_LED>;
>> + };
>> + };
>> };
>>
>> i2c6mux0chn5: i2c@5 {
>> @@ -542,6 +856,44 @@ i2c6mux0chn7: i2c@7 {
>> reg = <7>;
>> };
>> };
>> +
>> + pca3: pca9539@74 {
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
Fixed node names.
>
>
>> + compatible = "nxp,pca9539";
>> + reg = <0x74>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + };
>> +
>> + pca4: pca9539@77 {
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
Fixed node names.
>
>
>> + compatible = "nxp,pca9539";
>> + reg = <0x77>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> +
>> + gpio-line-names =
>> + "PE_NVMED0_EXP_PRSNT_N",
>> + "PE_NVMED1_EXP_PRSNT_N",
>> + "PE_NVMED2_EXP_PRSNT_N",
>> + "PE_NVMED3_EXP_PRSNT_N",
>> + "LED_FAULT_NVMED0",
>> + "LED_FAULT_NVMED1",
>> + "LED_FAULT_NVMED2",
>> + "LED_FAULT_NVMED3",
>> + "FAN0_PRESENCE_R_N",
>> + "FAN1_PRESENCE_R_N",
>> + "FAN2_PRESENCE_R_N",
>> + "FAN3_PRESENCE_R_N",
>> + "FAN4_PRESENCE_R_N",
>> + "FAN5_PRESENCE_N",
>> + "FAN6_PRESENCE_N",
>> + "";
>> + };
>> };
>>
>> &i2c7 {
>> @@ -809,6 +1161,191 @@ regulator@41 {
>> compatible = "infineon,ir38263";
>> reg = <0x41>;
>> };
>> +
>> + led-controller@61 {
>> + compatible = "nxp,pca9552";
>> + reg = <0x61>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
> ...
>
>> + led@15 {
>> + label = "pe-cp-drv3-perst";
>> + reg = <15>;
>> + retain-state-shutdown;
>> + default-state = "keep";
>> + type = <PCA955X_TYPE_LED>;
>> + };
>> + };
>> +
>> + pca1: pca9539@75 {
> Node names should be generic. See also an explanation and list of
> examples (not exhaustive) in DT specification:
> https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
Fixed names.

Thanks for the review.

Regards,

Ninad


\
 
 \ /
  Last update: 2024-01-08 20:58    [W:0.097 / U:0.296 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site