lkml.org 
[lkml]   [2024]   [Jan]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v2 09/20] media: i2c: ov4689: Use runtime PM autosuspend
Date
Hi Sakari,

Thanks for the review!

On 2024-01-08 at 11:18 GMT, Sakari Ailus <sakari.ailus@iki.fi> wrote:

> Hi Mikhail,
>
> On Mon, Dec 18, 2023 at 08:40:30PM +0300, Mikhail Rudenko wrote:
>> Use runtime PM autosuspend to avoid powering off the sensor during
>> fast stop-reconfigure-restart cycles.
>>
>> Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
>> ---
>> drivers/media/i2c/ov4689.c | 22 +++++++++++++++-------
>> 1 file changed, 15 insertions(+), 7 deletions(-)
>>
>> diff --git a/drivers/media/i2c/ov4689.c b/drivers/media/i2c/ov4689.c
>> index 5300e621ff90..64cc6d9e48cc 100644
>> --- a/drivers/media/i2c/ov4689.c
>> +++ b/drivers/media/i2c/ov4689.c
>> @@ -407,26 +407,27 @@ static int ov4689_s_stream(struct v4l2_subdev *sd, int on)
>> ov4689->cur_mode->num_regs,
>> NULL);
>> if (ret) {
>> - pm_runtime_put(dev);
>> + pm_runtime_put_sync(dev);
>
> Why are you switching to pm_runtime_put_sync() here? That isn't covered by
> the commit message (nor I think should be done).

PM autosuspend conversion was suggested earlier by Laurent in his review
of this series [1], and he adviced looking at how it was done for the
imx290 driver. I followed along the lines of the corresponding patch
[2].

>> goto unlock_and_return;
>> }
>>
>> ret = __v4l2_ctrl_handler_setup(&ov4689->ctrl_handler);
>> if (ret) {
>> - pm_runtime_put(dev);
>> + pm_runtime_put_sync(dev);
>> goto unlock_and_return;
>> }
>>
>> ret = cci_write(ov4689->regmap, OV4689_REG_CTRL_MODE,
>> OV4689_MODE_STREAMING, NULL);
>> if (ret) {
>> - pm_runtime_put(dev);
>> + pm_runtime_put_sync(dev);
>> goto unlock_and_return;
>> }
>> } else {
>> cci_write(ov4689->regmap, OV4689_REG_CTRL_MODE,
>> OV4689_MODE_SW_STANDBY, NULL);
>> - pm_runtime_put(dev);
>> + pm_runtime_mark_last_busy(dev);
>> + pm_runtime_put_autosuspend(dev);
>> }
>>
>> unlock_and_return:
>> @@ -606,7 +607,9 @@ static int ov4689_set_ctrl(struct v4l2_ctrl *ctrl)
>> break;
>> }
>>
>> - pm_runtime_put(dev);
>> + pm_runtime_mark_last_busy(dev);
>> + pm_runtime_put_autosuspend(dev);
>
> Also note that with runtime PM autosuspend, you have to use
> pm_runtime_get_if_active() instead of pm_runtime_get_if_in_use().

Noted, will do so in v3.

>> +
>> return ret;
>> }
>>
>> @@ -877,8 +880,10 @@ static int ov4689_probe(struct i2c_client *client)
>> }
>>
>> pm_runtime_set_active(dev);
>> + pm_runtime_get_noresume(dev);
>> pm_runtime_enable(dev);
>> - pm_runtime_idle(dev);
>> + pm_runtime_set_autosuspend_delay(dev, 1000);
>> + pm_runtime_use_autosuspend(dev);
>>
>> ret = v4l2_async_register_subdev_sensor(sd);
>> if (ret) {
>> @@ -886,11 +891,14 @@ static int ov4689_probe(struct i2c_client *client)
>> goto err_clean_subdev_pm;
>> }
>>
>> + pm_runtime_mark_last_busy(dev);
>> + pm_runtime_put_autosuspend(dev);
>> +
>> return 0;
>>
>> err_clean_subdev_pm:
>> pm_runtime_disable(dev);
>> - pm_runtime_set_suspended(dev);
>> + pm_runtime_put_noidle(dev);
>> v4l2_subdev_cleanup(sd);
>> err_clean_entity:
>> media_entity_cleanup(&sd->entity);

[1] https://lore.kernel.org/all/20231211181935.GG27535@pendragon.ideasonboard.com/
[2] https://lore.kernel.org/all/20230116144454.1012-14-laurent.pinchart@ideasonboard.com/

--
Best regards,
Mikhail Rudenko

\
 
 \ /
  Last update: 2024-01-08 16:45    [W:0.115 / U:0.968 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site