lkml.org 
[lkml]   [2024]   [Jan]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/1] net: mvpp2: clear BM pool before initialization
Date
Register value persisted after booting the kernel using
kexec which resulted in kernel panic. Thus cleared the
BM pool registers before initialisation to fix the issue.

Signed-off-by: Jenishkumar Maheshbhai Patel <jpatel2@marvell.com>
---
.../net/ethernet/marvell/mvpp2/mvpp2_main.c | 28 +++++++++++++++++++
1 file changed, 28 insertions(+)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 820b1fabe297..8223c00d1f91 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -614,12 +614,40 @@ static void mvpp23_bm_set_8pool_mode(struct mvpp2 *priv)
mvpp2_write(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG, val);
}

+/* Cleanup pool before actual initialization in the OS */
+static void mvpp2_bm_pool_cleanup(struct mvpp2 *priv, int pool_id)
+{
+ u32 val;
+ int i;
+ /* Drain the BM from all possible residues left by firmware */
+ for (i = 0; i < MVPP2_BM_POOL_SIZE_MAX; i++)
+ mvpp2_read(priv, MVPP2_BM_PHY_ALLOC_REG(pool_id));
+ /* Stop the BM pool */
+ val = mvpp2_read(priv, MVPP2_BM_POOL_CTRL_REG(pool_id));
+ val |= MVPP2_BM_STOP_MASK;
+ mvpp2_write(priv, MVPP2_BM_POOL_CTRL_REG(pool_id), val);
+ /* Mask BM all interrupts */
+ mvpp2_write(priv, MVPP2_BM_INTR_MASK_REG(pool_id), 0);
+ /* Clear BM cause register */
+ mvpp2_write(priv, MVPP2_BM_INTR_CAUSE_REG(pool_id), 0);
+}
+
static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
{
enum dma_data_direction dma_dir = DMA_FROM_DEVICE;
int i, err, poolnum = MVPP2_BM_POOLS_NUM;
struct mvpp2_port *port;

+ if (priv->percpu_pools)
+ poolnum = mvpp2_get_nrxqs(priv) * 2;
+
+ for (i = 0; i < poolnum; i++) {
+ /* Make sure about the pool state in case it was
+ * used by firmware.
+ */
+ mvpp2_bm_pool_cleanup(priv, i);
+ }
+
if (priv->percpu_pools) {
for (i = 0; i < priv->port_count; i++) {
port = priv->port_list[i];
--
2.25.1

\
 
 \ /
  Last update: 2024-01-16 06:58    [W:0.038 / U:0.816 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site