lkml.org 
[lkml]   [2023]   [Jun]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 6/8] PCI: qcom: Use post init sequence of IP v2.3.2 for v2.4.0
Date
The post init sequence of IP v2.4.0 is same as v2.3.2. So let's reuse the
v2.3.2 sequence which now also disables hotplug capability of the
controller as it is not at all supported on any SoCs making use of this IP.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
drivers/pci/controller/dwc/pcie-qcom.c | 30 +-------------------------
1 file changed, 1 insertion(+), 29 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 9c8dfd224e6e..e6db9e551752 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -703,34 +703,6 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)
return 0;
}

-static int qcom_pcie_post_init_2_4_0(struct qcom_pcie *pcie)
-{
- u32 val;
-
- /* enable PCIe clocks and resets */
- val = readl(pcie->parf + PARF_PHY_CTRL);
- val &= ~PHY_TEST_PWR_DOWN;
- writel(val, pcie->parf + PARF_PHY_CTRL);
-
- /* change DBI base address */
- writel(0, pcie->parf + PARF_DBI_BASE_ADDR);
-
- /* MAC PHY_POWERDOWN MUX DISABLE */
- val = readl(pcie->parf + PARF_SYS_CTRL);
- val &= ~MAC_PHY_POWERDOWN_IN_P2_D_MUX_EN;
- writel(val, pcie->parf + PARF_SYS_CTRL);
-
- val = readl(pcie->parf + PARF_MHI_CLOCK_RESET_CTRL);
- val |= BYPASS;
- writel(val, pcie->parf + PARF_MHI_CLOCK_RESET_CTRL);
-
- val = readl(pcie->parf + PARF_AXI_MSTR_WR_ADDR_HALT_V2);
- val |= EN;
- writel(val, pcie->parf + PARF_AXI_MSTR_WR_ADDR_HALT_V2);
-
- return 0;
-}
-
static int qcom_pcie_get_resources_2_3_3(struct qcom_pcie *pcie)
{
struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3;
@@ -1276,7 +1248,7 @@ static const struct qcom_pcie_ops ops_2_3_2 = {
static const struct qcom_pcie_ops ops_2_4_0 = {
.get_resources = qcom_pcie_get_resources_2_4_0,
.init = qcom_pcie_init_2_4_0,
- .post_init = qcom_pcie_post_init_2_4_0,
+ .post_init = qcom_pcie_post_init_2_3_2,
.deinit = qcom_pcie_deinit_2_4_0,
.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
};
--
2.25.1
\
 
 \ /
  Last update: 2023-06-01 18:40    [W:0.082 / U:0.304 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site