lkml.org 
[lkml]   [2023]   [May]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v3] firmware: qcom_scm: Clear download bit during reboot
From


On 5/22/2023 3:34 PM, Robert Marko wrote:
> On Mon, 22 May 2023 at 11:26, Robert Marko <robimarko@gmail.com> wrote:
>>
>> On Mon, 22 May 2023 at 11:11, Mukesh Ojha <quic_mojha@quicinc.com> wrote:
>>>
>>>
>>>
>>> On 5/22/2023 2:29 PM, Robert Marko wrote:
>>>> On Mon, 22 May 2023 at 08:11, Mukesh Ojha <quic_mojha@quicinc.com> wrote:
>>>>>
>>>>>
>>>>>
>>>>> On 5/18/2023 3:45 PM, Robert Marko wrote:
>>>>>>
>>>>>> On 16. 03. 2023. 16:14, Mukesh Ojha wrote:
>>>>>>> During normal restart of a system download bit should
>>>>>>> be cleared irrespective of whether download mode is
>>>>>>> set or not.
>>>>>>>
>>>>>>> Fixes: 8c1b7dc9ba22 ("firmware: qcom: scm: Expose download-mode control")
>>>>>>> Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
>>>>>>
>>>>>> Hi, this has been backported to 5.15.111, however it seems to be
>>>>>> breaking reboot
>>>>>> on IPQ4019 by causing the board to then hang in SBL with:
>>>>>> root@OpenWrt:/# reboot
>>>>>> root@OpenWrt:/# [ 76.473541] device lan1 left promiscuous mode
>>>>>> [ 76.474204] br-lan: port 1(lan1) entered disabled state
>>>>>> [ 76.527975] device lan2 left promiscuous mode
>>>>>> [ 76.530301] br-lan: port 2(lan2) entered disabled state
>>>>>> [ 76.579376] device lan3 left promiscuous mode
>>>>>> [ 76.581698] br-lan: port 3(lan3) entered disabled state
>>>>>> [ 76.638434] device lan4 left promiscuous mode
>>>>>> [ 76.638777] br-lan: port 4(lan4) entered disabled state
>>>>>> [ 76.978489] qca8k-ipq4019 c000000.switch wan: Link is Down
>>>>>> [ 76.978883] device eth0 left promiscuous mode
>>>>>> [ 76.987077] ipqess-edma c080000.ethernet eth0: Link is Down
>>>>>> [
>>>>>> Format: Log Type - Time(microsec) - Message - Optional Info
>>>>>> Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
>>>>>> S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00123
>>>>>> S - IMAGE_VARIANT_STRING=DAABANAZA
>>>>>> S - OEM_IMAGE_VERSION_STRING=CRM
>>>>>> S - Boot Config, 0x00000021
>>>>>> S - Reset status Config, 0x00000010
>>>>>> S - Core 0 Frequency, 0 MHz
>>>>>> B - 261 - PBL, Start
>>>>>> B - 1339 - bootable_media_detect_entry, Start
>>>>>> B - 1679 - bootable_media_detect_success, Start
>>>>>> B - 1693 - elf_loader_entry, Start
>>>>>> B - 5076 - auth_hash_seg_entry, Start
>>>>>> B - 7223 - auth_hash_seg_exit, Start
>>>>>> B - 578349 - elf_segs_hash_verify_entry, Start
>>>>>> B - 696356 - PBL, End
>>>>>> B - 696380 - SBL1, Start
>>>>>> B - 787236 - pm_device_init, Start
>>>>>> D - 7 - pm_device_init, Delta
>>>>>> B - 788701 - boot_flash_init, Start
>>>>>> D - 52782 - boot_flash_init, Delta
>>>>>> B - 845625 - boot_config_data_table_init, Start
>>>>>> D - 3836 - boot_config_data_table_init, Delta - (419 Bytes)
>>>>>> B - 852841 - clock_init, Start
>>>>>> D - 7566 - clock_init, Delta
>>>>>> B - 864883 - CDT version:2,Platform ID:9,Major ID:0,Minor
>>>>>> ID:0,Subtype:64
>>>>>> B - 868413 - sbl1_ddr_set_params, Start
>>>>>> B - 873402 - cpr_init, Start
>>>>>> D - 2 - cpr_init, Delta
>>>>>> B - 877842 - Pre_DDR_clock_init, Start
>>>>>> D - 4 - Pre_DDR_clock_init, Delta
>>>>>> D - 13234 - sbl1_ddr_set_params, Delta
>>>>>> B - 891155 - pm_driver_init, Start
>>>>>> D - 2 - pm_driver_init, Delta
>>>>>> B - 909105 - Image Load, Start
>>>>>> B - 1030210 - Boot error ocuured!. Error code: 303d
>>>>>>
>>>>>> Reverting the commit fixes rebooting.
>>>>>
>>>>> Hi Robert,
>>>>>
>>>>> Can you check if disable SDI [1] works with this issue
>>>>>
>>>>> https://lore.kernel.org/linux-arm-msm/20230518140224.2248782-1-robimarko@gmail.com/
>>>>>
>>>>> [1]
>>>>>
>>>>>
>>>>> diff --git a/drivers/firmware/qcom_scm.c b/drivers/firmware/qcom_scm.c
>>>>> index fde33acd46b7..01496ceb7136 100644
>>>>> --- a/drivers/firmware/qcom_scm.c
>>>>> +++ b/drivers/firmware/qcom_scm.c
>>>>> @@ -1508,6 +1508,7 @@ static int qcom_scm_probe(struct platform_device
>>>>> *pdev)
>>>>> static void qcom_scm_shutdown(struct platform_device *pdev)
>>>>> {
>>>>> /* Clean shutdown, disable download mode to allow normal restart */
>>>>> + qcom_scm_disable_sdi();
>>>>> qcom_scm_set_download_mode(false);
>>>>> }
>>>>
>>>> Hi,
>>>> I can confirm reboot works this way as well.
>>>
>>> That's great, So, i don't need to revert the patch and you can
>>> add this in your patch without target specific check ?
>>
>> Oh, you mean IPQ4019 not rebooting?
>> I haven't tested that, give me couple of minutes to try that out.
>> Cause, the link was just back to the SDI patchset.
>
> And, I can confirm that IPQ4019 does not reboot even with SDI disabled if dload
> mode was set so it still needs a revert.

Ok, So, before we go for revert of the change.

- How do you generally collect the ram dump on your device on crash ?
did you check if you get any error when qcom_scm_set_download_mode()
get called.


-- Mukesh

>
> Regards,
> Robert
>>
>> Regards,
>> Robert
>>>
>>> -- Mukesh
>>>
>>>>
>>>> Regards,
>>>> Robert
>>>>>
>>>>>
>>>>> -- Mukesh
>>>>>
>>>>>>
>>>>>> Regards,
>>>>>> Robert
>>>>>>
>>>>>>> ---
>>>>>>> Changes in v3:
>>>>>>> - Added Fixes tag.
>>>>>>> - Removed it from below patch series, as it makes sense to go this
>>>>>>> independently.
>>>>>>>
>>>>>>> https://lore.kernel.org/lkml/1677664555-30191-1-git-send-email-quic_mojha@quicinc.com/
>>>>>>>
>>>>>>> Changes in v2:
>>>>>>> - No change.
>>>>>>>
>>>>>>> drivers/firmware/qcom_scm.c | 3 +--
>>>>>>> 1 file changed, 1 insertion(+), 2 deletions(-)
>>>>>>>
>>>>>>> diff --git a/drivers/firmware/qcom_scm.c b/drivers/firmware/qcom_scm.c
>>>>>>> index 468d4d5..3e020d1 100644
>>>>>>> --- a/drivers/firmware/qcom_scm.c
>>>>>>> +++ b/drivers/firmware/qcom_scm.c
>>>>>>> @@ -1506,8 +1506,7 @@ static int qcom_scm_probe(struct platform_device
>>>>>>> *pdev)
>>>>>>> static void qcom_scm_shutdown(struct platform_device *pdev)
>>>>>>> {
>>>>>>> /* Clean shutdown, disable download mode to allow normal restart */
>>>>>>> - if (download_mode)
>>>>>>> - qcom_scm_set_download_mode(false);
>>>>>>> + qcom_scm_set_download_mode(false);
>>>>>>> }
>>>>>>> static const struct of_device_id qcom_scm_dt_match[] = {

\
 
 \ /
  Last update: 2023-05-23 11:43    [W:0.173 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site