lkml.org 
[lkml]   [2023]   [May]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH net-next 04/30] net: dsa: mt7530: improve comments regarding port 5 and 6
Date
From: Arınç ÜNAL <arinc.unal@arinc9.com>

There's no logic to numerically order the CPU ports. State the port number
and its capability of being used as a CPU port instead.

Remove the irrelevant PHY muxing information from
mt7530_mac_port_get_caps(). Explain the supported MII modes instead.

Remove the out of place PHY muxing information from
mt753x_phylink_mac_config(). The function is for both the MT7530 and MT7531
switches but there's no PHY muxing on MT7531.

These comments were gradually introduced with the commits below.
ca366d6c889b ("net: dsa: mt7530: Convert to PHYLINK API")
38f790a80560 ("net: dsa: mt7530: Add support for port 5")
88bdef8be9f6 ("net: dsa: mt7530: Extend device data ready for adding a new
hardware")
c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
---
drivers/net/dsa/mt7530.c | 19 +++++++++++++------
1 file changed, 13 insertions(+), 6 deletions(-)

diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 024b853f9558..b28d66a7c0b2 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2499,7 +2499,9 @@ static void mt7530_mac_port_get_caps(struct dsa_switch *ds, int port,
config->supported_interfaces);
break;

- case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
+ case 5: /* Port 5 which can be used as a CPU port supports rgmii with
+ * delays, mii, and gmii.
+ */
phy_interface_set_rgmii(config->supported_interfaces);
__set_bit(PHY_INTERFACE_MODE_MII,
config->supported_interfaces);
@@ -2507,7 +2509,9 @@ static void mt7530_mac_port_get_caps(struct dsa_switch *ds, int port,
config->supported_interfaces);
break;

- case 6: /* 1st cpu port */
+ case 6: /* Port 6 which can be used as a CPU port supports rgmii and
+ * trgmii.
+ */
__set_bit(PHY_INTERFACE_MODE_RGMII,
config->supported_interfaces);
__set_bit(PHY_INTERFACE_MODE_TRGMII,
@@ -2527,14 +2531,17 @@ static void mt7531_mac_port_get_caps(struct dsa_switch *ds, int port,
config->supported_interfaces);
break;

- case 5: /* 2nd cpu port supports either rgmii or sgmii/8023z */
+ case 5: /* Port 5 which can be used as a CPU port supports rgmii with
+ * delays on MT7531BE, sgmii/802.3z on MT7531AE.
+ */
if (!priv->p5_sgmii) {
phy_interface_set_rgmii(config->supported_interfaces);
break;
}
fallthrough;

- case 6: /* 1st cpu port supports sgmii/8023z only */
+ case 6: /* Port 6 which can be used as a CPU port supports sgmii/802.3z.
+ */
__set_bit(PHY_INTERFACE_MODE_SGMII,
config->supported_interfaces);
__set_bit(PHY_INTERFACE_MODE_1000BASEX,
@@ -2726,7 +2733,7 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
state->interface != PHY_INTERFACE_MODE_INTERNAL)
goto unsupported;
break;
- case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
+ case 5: /* Port 5, can be used as a CPU port. */
if (priv->p5_interface == state->interface)
break;

@@ -2736,7 +2743,7 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
if (priv->p5_intf_sel != P5_DISABLED)
priv->p5_interface = state->interface;
break;
- case 6: /* 1st cpu port */
+ case 6: /* Port 6, can be used as a CPU port. */
if (priv->p6_interface == state->interface)
break;

--
2.39.2
\
 
 \ /
  Last update: 2023-05-22 14:18    [W:0.752 / U:0.264 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site