lkml.org 
[lkml]   [2023]   [May]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v8 6/9] usb: dwc3: qcom: Add multiport controller support for qcom wrapper
From


On 5/16/2023 3:57 AM, Bjorn Andersson wrote:
> On Sun, May 14, 2023 at 11:19:14AM +0530, Krishna Kurapati wrote:
>> QCOM SoC SA8295P's tertiary quad port controller supports 2 HS+SS
>> ports and 2 HS only ports. Add support for configuring PWR_EVENT_IRQ's
>> for all the ports during suspend/resume.
>>
>> Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
>> ---
>> drivers/usb/dwc3/dwc3-qcom.c | 28 ++++++++++++++++++++++------
>> 1 file changed, 22 insertions(+), 6 deletions(-)
>>
>> diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
>> index 959fc925ca7c..7a9bce66295d 100644
>> --- a/drivers/usb/dwc3/dwc3-qcom.c
>> +++ b/drivers/usb/dwc3/dwc3-qcom.c
>> @@ -37,7 +37,10 @@
>> #define PIPE3_PHYSTATUS_SW BIT(3)
>> #define PIPE_UTMI_CLK_DIS BIT(8)
>>
>> -#define PWR_EVNT_IRQ_STAT_REG 0x58
>> +#define PWR_EVNT_IRQ1_STAT_REG 0x58
>> +#define PWR_EVNT_IRQ2_STAT_REG 0x1dc
>> +#define PWR_EVNT_IRQ3_STAT_REG 0x228
>> +#define PWR_EVNT_IRQ4_STAT_REG 0x238
>> #define PWR_EVNT_LPM_IN_L2_MASK BIT(4)
>> #define PWR_EVNT_LPM_OUT_L2_MASK BIT(5)
>>
>> @@ -93,6 +96,13 @@ struct dwc3_qcom {
>> struct icc_path *icc_path_apps;
>> };
>>
>> +static u32 pwr_evnt_irq_stat_reg_offset[4] = {
>> + PWR_EVNT_IRQ1_STAT_REG,
>> + PWR_EVNT_IRQ2_STAT_REG,
>> + PWR_EVNT_IRQ3_STAT_REG,
>> + PWR_EVNT_IRQ4_STAT_REG,
>
> Seems to be excessive indentation of these...
>
> Can you also please confirm that these should be counted starting at 1 -
> given that you otherwise talk about port0..N-1?
>
Hi Bjorn,

I am fine with either way. Since this just denoted 4 different ports,
I named them starting with 1. Either ways, we will run through array
from (0-3), so we must be fine.

>> +};
>> +
>> static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val)
>> {
>> u32 reg;
>> @@ -413,13 +423,16 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom, bool wakeup)
>> {
>> u32 val;
>> int i, ret;
>> + struct dwc3 *dwc = platform_get_drvdata(qcom->dwc3);
>>
>> if (qcom->is_suspended)
>> return 0;
>>
>> - val = readl(qcom->qscratch_base + PWR_EVNT_IRQ_STAT_REG);
>> - if (!(val & PWR_EVNT_LPM_IN_L2_MASK))
>> - dev_err(qcom->dev, "HS-PHY not in L2\n");
>> + for (i = 0; i < dwc->num_usb2_ports; i++) {
>
> In the event that the dwc3 core fails to acquire or enable e.g. clocks
> its drvdata will be NULL. If you then hit a runtime pm transition in the
> dwc3-qcom glue you will dereference NULL here. (You can force this issue
> by e.g. returning -EINVAL from dwc3_clk_enable()).
>
> So if you're peaking into qcom->dwc3 you need to handle the fact that
> dwc might be NULL, here and in resume below.
>
Thanks for catching this. You are right, there were instances where the
we saw probe for dwc3 being deferred while the probe for dwc3-qcom was
still successful [1]. In this case, if the dwc3 probe never happened and
system tries to enter suspend, we might hit a NULL pointer dereference.

I will fix this in v9.

[1]:
https://patchwork.kernel.org/project/linux-usb/patch/1657809067-25815-1-git-send-email-quic_kriskura@quicinc.com/

Regards,
Krishna,

\
 
 \ /
  Last update: 2023-05-16 04:22    [W:0.143 / U:0.468 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site