lkml.org 
[lkml]   [2023]   [Apr]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
Subject[PATCH v2 2/4] arm64: dts: qcom: sm8150-kumano: Add GPIO line names for TLMM
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).

Add these to the common DTSI to better document the hardware.

The pin assignment for TLMM is identical on both devices. Great job!

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
.../boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi | 175 +++++++++++++++++++++
1 file changed, 175 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi b/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi
index 6753c65d75bc..d1a3ab836019 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano.dtsi
@@ -541,6 +541,181 @@ &qupv3_id_1 {

&tlmm {
gpio-reserved-ranges = <126 4>;
+ gpio-line-names = "NFC_ESE_SPI_MISO", /* GPIO_0 */
+ "NFC_ESE_SPI_MOSI",
+ "NFC_ESE_SPI_SCLK",
+ "NFC_ESE_SPI_CS_N",
+ "NC",
+ "NC",
+ "DISP_RESET_N",
+ "DEBUG_GPIO0",
+ "MDP_VSYNC_P",
+ "TS_I2C_SDA",
+ "TS_I2C_SCL", /* GPIO_10 */
+ "CAM_SOF",
+ "CAM2_RST_N",
+ "CAM_MCLK0",
+ "CAM_MCLK1",
+ "CAM_MCLK2",
+ "CAM_MCLK3",
+ "CCI_I2C_SDA0",
+ "CCI_I2C_SCL0",
+ "CCI_I2C_SDA1",
+ "CCI_I2C_SCL1", /* GPIO_20 */
+ "NC",
+ "MAIN_CAM_PWR_EN",
+ "CAM3_RST_N",
+ "NC",
+ "CHAT_CAM_PWR_EN",
+ "NC",
+ "NC",
+ "CAM0_RST_N",
+ "RGBC_IR_PWR_EN",
+ "CAM1_RST_N", /* GPIO_30 */
+ "CCI_I2C_SDA2",
+ "CCI_I2C_SCL2",
+ "CCI_I2C_SDA3",
+ "CCI_I2C_SCL3",
+ "NC",
+ "DEBUG_GPIO1",
+ "RGBC_IR_INT",
+ "USB_CC_DIR",
+ "NC",
+ "NC", /* GPIO_40 */
+ "NFC_EN",
+ "NFC_ESE_PWR_REQ",
+ "BT_HCI_UART_CTS_N",
+ "BT_HCI_UART_RFR_N",
+ "BT_HCI_UART_TXD",
+ "BT_HCI_UART_RXD",
+ "NFC_IRQ",
+ "NFC_DWL_REQ",
+ "UIM2_DETECT_EN",
+ "WLAN_SW_CTRL", /* GPIO_50 */
+ "APPS_I2C_SDA",
+ "APPS_I2C_SCL",
+ "NC",
+ "TS_RESET_N",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "HW_ID_0",
+ "NC", /* GPIO_60 */
+ "QLINK_REQUEST",
+ "QLINK_ENABLE",
+ "WMSS_RESET_N",
+ "SDM_GRFC_8",
+ "WDOG_DISABLE",
+ "NC",
+ "NC",
+ "PA_INDICATOR_OR",
+ "MSS_LTE_COXM_TXD",
+ "MSS_LTE_COXM_RXD", /* GPIO_70 */
+ "SDM_RFFE0_DATA",
+ "SDM_RFFE0_CLK",
+ "SDM_RFFE1_DATA",
+ "SDM_RFFE1_CLK",
+ "SDM_RFFE2_DATA",
+ "SDM_RFFE2_CLK",
+ "SDM_RFFE3_DATA",
+ "SDM_RFFE3_CLK",
+ "SUB_CAM_PWR_EN",
+ "FP_RESET_N", /* GPIO_80 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "DEBUG_UART_TX",
+ "DEBUG_UART_RX",
+ "DVDT_WRT_DET_AND",
+ "NC",
+ "NC",
+ "NC", /* GPIO_90 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "UDON_SWITCH_SEL",
+ "SD_CARD_DET_N",
+ "NC",
+ "CAMSENSOR_I2C_SDA",
+ "CAMSENSOR_I2C_SCL",
+ "USB_AUDIO_EN1", /* GPIO_100 */
+ "DISP_ERR_FG",
+ "NC",
+ "NC",
+ "NC",
+ "UIM2_DATA",
+ "UIM2_CLK",
+ "UIM2_RESET",
+ "UIM2_DET",
+ "UIM1_DATA",
+ "UIM1_CLK", /* GPIO_110 */
+ "UIM1_RESET",
+ "UIM1_PRESENT",
+ "NFC_CLK_REQ",
+ "SW_SERVICE",
+ "NC",
+ "RF_ID_EXTENSION",
+ "ALS_PROX_INT_N",
+ "FP_INT",
+ "DVDT_WRT_DET_OR",
+ "BAROMETER_INT", /* GPIO_120 */
+ "ACC_COVER_OPEN",
+ "TS_INT_N",
+ "CODEC_INT1_N",
+ "CODEC_INT2_N",
+ "TX_GTR_THRES_IN",
+ "FP_SPI_MISO",
+ "FP_SPI_MOSI",
+ "FP_SPI_SCLK",
+ "FP_SPI_CS_N",
+ "NC", /* GPIO_130 */
+ "DVDT_ENABLE",
+ "ACCEL_INT",
+ "NC",
+ "MAG_INT_N",
+ "NC",
+ "FORCED_USB_BOOT",
+ "NC",
+ "NC",
+ "HW_ID_1",
+ "NC", /* GPIO_140 */
+ "NC",
+ "NC",
+ "CODEC_RST_N",
+ "CDC_SPI_MISO",
+ "CDC_SPI_MOSI",
+ "CDC_SPI_SCLK",
+ "CDC_SPI_CS_N",
+ "NC",
+ "LPASS_SLIMBUS_CLK",
+ "LPASS_SLIMBUS_DATA0", /* GPIO_150 */
+ "LPASS_SLIMBUS_DATA1",
+ "USB_AUDIO_EN2",
+ "BT_FM_SLIMBUS_DATA",
+ "BT_FM_SLIMBUS_CLK",
+ "COMPASS_I2C_SDA",
+ "COMPASS_I2C_SCL",
+ "SSC_SPI_1_MISO",
+ "SSC_SPI_1_MOSI",
+ "SSC_SPI_1_CLK",
+ "SSC_SPI_1_CS_N", /* GPIO_160 */
+ "SSC_SENSOR_I2C_SDA",
+ "SSC_SENSOR_I2C_SCL",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "SSC_UART_1_TX",
+ "SSC_UART_1_RX",
+ "WL_CMD_CLK_CHAIN0",
+ "WL_CMD_DATA_CHAIN0", /* GPIO_170 */
+ "WL_CMD_CLK_CHAIN1",
+ "WL_CMD_DATA_CHAIN1",
+ "WL_BT_COEX_CLK",
+ "WL_BT_COEX_DATA";
};

&uart2 {
--
2.40.0

\
 
 \ /
  Last update: 2023-04-11 20:17    [W:0.140 / U:0.152 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site