lkml.org 
[lkml]   [2023]   [Mar]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH net-next v2 4/6] net: mdio: scan bus based on bus capabilities for C22 and C45
From
Date
On Wed, 2023-01-18 at 11:01 +0100, Michael Walle wrote:
> From: Andrew Lunn <andrew@lunn.ch>
>
> Now that all MDIO bus drivers which set probe_capabilities to
> MDIOBUS_C22_C45 have been converted to use the name API for C45
> transactions, perform the scanning of the bus based on which methods
> the bus provides.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Michael Walle <michael@walle.cc>
> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>

Hello,

On a Turris Omnia (Armada 385, Marvell 88E6176) this commit results
in a strange boot behaviour. I see two distinct multi-second freezes
in dmesg. Usually (up to the commit before), the (monolithic) kernel
starts init after ~1.6 seconds, now it takes more than 6....

dmesg output below. Any idea, why this is happening?

Best regards, Klaus

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 6.2.0-rc3+ (xxxx) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Sun Mar 5 16:20:57 CET 2023
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Turris Omnia
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000] HighMem [mem 0x0000000030000000-0x000000003fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000] percpu: Embedded 12 pages/cpu s19604 r8192 d21356 u49152
[ 0.000000] pcpu-alloc: s19604 r8192 d21356 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416
[ 0.000000] Kernel command line: console=ttyS0,115200 quiet root=PARTUUID=262ecdb3-01 mvneta.txq_number=2 mvneta.rxq_number=2
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 1022716K/1048576K available (7168K kernel code, 590K rwdata, 1776K rodata, 1024K init, 233K bss, 25860K reserved, 0K cma-reserved, 262144K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000001] sched_clock: 64 bits at 800MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.000012] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0xb881274fa3, max_idle_ns: 440795210636 ns
[ 0.000026] Switching to timer-based delay loop, resolution 1ns
[ 0.000153] Ignoring duplicate/late registration of read_current_timer delay
[ 0.000159] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000302] Calibrating delay loop (skipped), value calculated using timer frequency.. 1600.00 BogoMIPS (lpj=3200000)
[ 0.000310] pid_max: default: 32768 minimum: 301
[ 0.000396] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.000403] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.000726] CPU: Testing write buffer coherency: ok
[ 0.000749] CPU0: Spectre v2: using BPIALL workaround
[ 0.000864] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001188] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.001192] cblist_init_generic: Setting shift to 1 and lim to 1.
[ 0.001241] Setting up static identity map for 0x100000 - 0x100060
[ 0.001314] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[ 0.001393] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.001458] rcu: Hierarchical SRCU implementation.
[ 0.001460] rcu: Max phase no-delay instances is 1000.
[ 0.001631] smp: Bringing up secondary CPUs ...
[ 0.001833] Booting CPU 1
[ 0.001955] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.001962] CPU1: Spectre v2: using BPIALL workaround
[ 0.002016] smp: Brought up 1 node, 2 CPUs
[ 0.002020] SMP: Total of 2 processors activated (3200.00 BogoMIPS).
[ 0.002025] CPU: All CPU(s) started in SVC mode.
[ 0.002291] devtmpfs: initialized
[ 0.004089] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.004132] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.004141] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.004196] pinctrl core: initialized pinctrl subsystem
[ 0.004478] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.004981] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.005337] thermal_sys: Registered thermal governor 'step_wise'
[ 0.005440] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.005445] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.010021] SCSI subsystem initialized
[ 0.010039] libata version 3.00 loaded.
[ 0.010094] usbcore: registered new interface driver usbfs
[ 0.010107] usbcore: registered new interface driver hub
[ 0.010123] usbcore: registered new device driver usb
[ 0.010716] clocksource: Switched to clocksource arm_global_timer
[ 0.011194] NET: Registered PF_INET protocol family
[ 0.011303] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.012144] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.012157] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.012164] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.012201] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[ 0.012316] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.012363] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.012389] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.012498] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.013022] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.013133] Unpacking initramfs...
[ 0.013356] NET: Registered PF_ALG protocol family
[ 0.013390] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.013406] io scheduler bfq registered
[ 0.018260] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 0.018567] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 0.018922] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 0.019318] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.047355] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.047527] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.075302] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.075544] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
[ 0.076072] printk: console [ttyS0] disabled
[ 0.076106] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 38, base_baud = 15625000) is a 16550A
[ 0.076131] printk: console [ttyS0] enabled
[ 0.076545] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 39, base_baud = 15625000) is a 16550A
[ 0.077023] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 0.077035] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 0.077454] scsi host0: ahci-mvebu
[ 0.077669] scsi host1: ahci-mvebu
[ 0.077746] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 40
[ 0.077752] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 40
[ 0.078389] spi-nor spi0.0: s25fl164k (8192 Kbytes)
[ 0.186266] Freeing initrd memory: 4576K
[ 0.194291] 3 fixed-partitions partitions found on MTD device spi0.0
[ 0.194305] Creating 3 MTD partitions on "spi0.0":
[ 0.194310] 0x000000000000-0x0000000f0000 : "U-Boot"
[ 0.194494] 0x000000100000-0x000000800000 : "Rescue system"
[ 0.194609] 0x0000000f0000-0x000000100000 : "u-boot-env"
[ 0.202428] mv88e6085 f1072004.mdio-mii:10: switch 0x1760 detected: Marvell 88E6176, revision 1
[ 0.392679] ata2: SATA link down (SStatus 0 SControl 300)
[ 0.554721] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 0.555400] ata1.00: supports DRM functions and may not be fully accessible
[ 0.555404] ata1.00: ATA-10: KINGSTON SKC600MS512G, S4800105, max UDMA/133
[ 0.555410] ata1.00: 1000215216 sectors, multi 1: LBA48 NCQ (depth 32)
[ 0.556078] ata1.00: Features: Trust Dev-Sleep
[ 0.556178] ata1.00: supports DRM functions and may not be fully accessible
[ 0.556830] ata1.00: configured for UDMA/133
[ 0.557003] scsi 0:0:0:0: Direct-Access ATA KINGSTON SKC600M 0105 PQ: 0 ANSI: 5
[ 0.557513] sd 0:0:0:0: [sda] 1000215216 512-byte logical blocks: (512 GB/477 GiB)
[ 0.557521] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 0.557542] sd 0:0:0:0: [sda] Write Protect is off
[ 0.557548] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.557582] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.557650] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[ 0.558138] sda: sda1
[ 0.558252] sd 0:0:0:0: [sda] Attached SCSI removable disk
*** FREEZE ***
[ 2.779254] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
[ 2.780632] mvneta f1070000.ethernet eth0: Using device tree mac address d8:58:d7:00:6f:b9
[ 2.781609] mvneta f1030000.ethernet eth1: Using device tree mac address d8:58:d7:00:6f:b7
[ 2.782547] mvneta f1034000.ethernet eth2: Using device tree mac address d8:58:d7:00:6f:b8
[ 2.782747] orion-ehci f1058000.usb: EHCI Host Controller
[ 2.782761] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 2.782807] orion-ehci f1058000.usb: irq 45, io mem 0xf1058000
[ 2.798726] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 2.799034] hub 1-0:1.0: USB hub found
[ 2.799053] hub 1-0:1.0: 1 port detected
[ 2.799415] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 2.799427] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[ 2.799475] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 2.799497] xhci-hcd f10f0000.usb3: irq 46, io mem 0xf10f0000
[ 2.799506] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 2.799513] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[ 2.799525] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed
[ 2.799776] hub 2-0:1.0: USB hub found
[ 2.799793] hub 2-0:1.0: 1 port detected
[ 2.799927] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.800135] hub 3-0:1.0: USB hub found
[ 2.800152] hub 3-0:1.0: 1 port detected
[ 2.800329] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 2.800340] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[ 2.800383] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 2.800404] xhci-hcd f10f8000.usb3: irq 47, io mem 0xf10f8000
[ 2.800414] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 2.800421] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 2.800431] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
[ 2.800671] hub 4-0:1.0: USB hub found
[ 2.800687] hub 4-0:1.0: 1 port detected
[ 2.800824] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.801039] hub 5-0:1.0: USB hub found
[ 2.801055] hub 5-0:1.0: 1 port detected
[ 2.801293] usbcore: registered new interface driver uas
[ 2.801337] usbcore: registered new interface driver usb-storage
[ 2.801815] armada38x-rtc f10a3800.rtc: registered as rtc0
[ 2.801892] armada38x-rtc f10a3800.rtc: setting system clock to 2023-03-05T16:48:56 UTC (1678034936)
[ 2.803556] at24 1-0054: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
[ 2.803591] i2c i2c-0: Added multiplexed i2c bus 1
[ 2.803627] i2c i2c-0: Added multiplexed i2c bus 2
[ 2.803657] i2c i2c-0: Added multiplexed i2c bus 3
[ 2.803688] i2c i2c-0: Added multiplexed i2c bus 4
[ 2.803717] i2c i2c-0: Added multiplexed i2c bus 5
[ 2.803796] i2c i2c-0: Added multiplexed i2c bus 6
[ 2.803828] i2c i2c-0: Added multiplexed i2c bus 7
[ 2.804026] pca953x 8-0071: using no AI
[ 2.805622] i2c i2c-0: Added multiplexed i2c bus 8
[ 2.805630] pca954x 0-0070: registered 8 multiplexed busses for I2C mux pca9547
[ 2.807069] orion_wdt: Initial timeout 171 sec
[ 2.807255] sdhci: Secure Digital Host Controller Interface driver
[ 2.807259] sdhci: Copyright(c) Pierre Ossman
[ 2.807320] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.816014] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 2.816451] NET: Registered PF_INET6 protocol family
[ 2.817118] Segment Routing with IPv6
[ 2.817146] In-situ OAM (IOAM) with IPv6
[ 2.817208] NET: Registered PF_PACKET protocol family
[ 2.817323] Registering SWP/SWPB emulation handler
[ 2.838752] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA
[ 2.915557] sfp sfp: Host maximum power 3.0W
[ 2.919406] mv88e6085 f1072004.mdio-mii:10: switch 0x1760 detected: Marvell 88E6176, revision 1
[ 2.942956] mmc0: new high speed MMC card at address 0001
[ 2.943334] mmcblk0: mmc0:0001 H8G4a\x92 7.28 GiB
[ 2.944348] mmcblk0: p1
[ 2.944624] mmcblk0boot0: mmc0:0001 H8G4a\x92 4.00 MiB
[ 2.944926] mmcblk0boot1: mmc0:0001 H8G4a\x92 4.00 MiB
[ 2.945157] mmcblk0rpmb: mmc0:0001 H8G4a\x92 4.00 MiB, chardev (250:0)
[ 3.246121] sfp sfp: module TP-LINK TL-SM321B rev sn 1403076900 dc 140401
[ 3.246143] mvneta f1034000.ethernet eth2: switched to inband/1000base-x link mode
*** FREEZE ***
[ 5.956754] mv88e6085 f1072004.mdio-mii:10: configuring for fixed/rgmii-id link mode
[ 5.958419] mv88e6085 f1072004.mdio-mii:10: configuring for fixed/rgmii-id link mode
[ 5.959693] mv88e6085 f1072004.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off
[ 5.963191] mv88e6085 f1072004.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off
[ 6.030496] mv88e6085 f1072004.mdio-mii:10 lan0 (uninitialized): PHY [mv88e6xxx-1:00] driver [Marvell 88E1540] (irq=68)
[ 6.102678] mv88e6085 f1072004.mdio-mii:10 lan1 (uninitialized): PHY [mv88e6xxx-1:01] driver [Marvell 88E1540] (irq=69)
[ 6.174861] mv88e6085 f1072004.mdio-mii:10 lan2 (uninitialized): PHY [mv88e6xxx-1:02] driver [Marvell 88E1540] (irq=70)
[ 6.246141] mv88e6085 f1072004.mdio-mii:10 lan3 (uninitialized): PHY [mv88e6xxx-1:03] driver [Marvell 88E1540] (irq=71)
[ 6.318682] mv88e6085 f1072004.mdio-mii:10 lan4 (uninitialized): PHY [mv88e6xxx-1:04] driver [Marvell 88E1540] (irq=72)
[ 6.321598] device eth1 entered promiscuous mode
[ 6.322472] device eth0 entered promiscuous mode
[ 6.322491] DSA: tree 0 setup
[ 6.323315] Freeing unused kernel image (initmem) memory: 1024K
[ 6.323453] Run /init as init process
[ 6.323457] with arguments:
[ 6.323459] /init
[ 6.323461] with environment:
[ 6.323463] HOME=/
[ 6.323465] TERM=linux

\
 
 \ /
  Last update: 2023-03-27 00:44    [W:0.202 / U:0.728 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site