lkml.org 
[lkml]   [2023]   [Feb]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [RFC PATCH v2 1/2] PM: domains: Skip disabling unused domains if provider has sync_state
From
On 03/02/2023 03:20, Matthias Kaehlcke wrote:
> Hi Dmitry,
>
> On Thu, Feb 02, 2023 at 09:53:41PM +0200, Dmitry Baryshkov wrote:
>> On 02/02/2023 20:24, Matthias Kaehlcke wrote:
>>> Hi Abel,
>>>
>>> On Fri, Jan 27, 2023 at 12:40:53PM +0200, Abel Vesa wrote:
>>>> Currently, there are cases when a domain needs to remain enabled until
>>>> the consumer driver probes. Sometimes such consumer drivers may be built
>>>> as modules. Since the genpd_power_off_unused is called too early for
>>>> such consumer driver modules to get a chance to probe, the domain, since
>>>> it is unused, will get disabled. On the other hand, the best time for
>>>> an unused domain to be disabled is on the provider's sync_state
>>>> callback. So, if the provider has registered a sync_state callback,
>>>> assume the unused domains for that provider will be disabled on its
>>>> sync_state callback. Also provide a generic sync_state callback which
>>>> disables all the domains unused for the provider that registers it.
>>>>
>>>> Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
>>>> ---
>>>>
>>>> This approach has been applied for unused clocks as well.
>>>> With this patch merged in, all the providers that have sync_state
>>>> callback registered will leave the domains enabled unless the provider's
>>>> sync_state callback explicitly disables them. So those providers will
>>>> need to add the disabling part to their sync_state callback. On the
>>>> other hand, the platforms that have cases where domains need to remain
>>>> enabled (even if unused) until the consumer driver probes, will be able,
>>>> with this patch in, to run without the pd_ignore_unused kernel argument,
>>>> which seems to be the case for most Qualcomm platforms, at this moment.
>>>
>>> I recently encountered a related issue on a Qualcomm platform with a
>>> v6.2-rc kernel, which includes 3a39049f88e4 ("soc: qcom: rpmhpd: Use
>>> highest corner until sync_state"). The issue involves a DT node with a
>>> rpmhpd, the DT node is enabled, however the corresponding device driver
>>> is not enabled in the kernel. In such a scenario the sync_state callback
>>> is never called, because the genpd consumer never probes. As a result
>>> the Always-on subsystem (AOSS) of the SoC doesn't enter sleep mode during
>>> system suspend, which results in a substantially higher power consumption
>>> in S3.
>>>
>>> I wonder if genpd (and some other frameworks) needs something like
>>> regulator_init_complete(), which turns off unused regulators 30s after
>>> system boot. That's conceptually similar to the current
>>> genpd_power_off_unused(), but would provide time for modules being loaded.
>>
>> I think the overall goal is to move away from ad-hoc implementations like
>> clk_disable_unused/genpd_power_off_unused/regulator_init_complete towards
>> the sync_state.
>
> I generally agree with the goal of using common mechanisms whenever possible.
>
>> So inherently one either has to provide drivers for all devices in question
>> or disable unused devices in DT.
>
> I don't think that's a great solution, it essentially hands the issue down to
> the users or downstream maintainers of the kernel, who might not be aware that
> there is an issue, nor know about the specifics of genpd (or interconnects and
> clocks which have similar problems).

The goal is to move the control down to individual drivers. Previously
we had issues with clk_disable_unused() disabling mdss/mdp clocks
incorrectly, which frequently led to broken display output. Other
clock/genpd/regulator drivers might have other internal dependencies.
Thus it is not really possible to handle resource shutdown in the common
(framework) code.

>
> In general symptoms are probably subtle, like a (potentially substantially)
> increased power consumption during system suspend. The issue might have been
> introduced by an update to a newer kernel, which now includes a DT node for a
> new SoC feature which wasn't supported by the 'old' kernel. It's common
> practice to use the 'old' .config, at least as a starting point, which
> obviously doesn't enable the new driver. That happend to me with [1] when
> testing v6.1. It took me quite some time to track the 'culprit' commit down
> and then some debugging to understand what's going on. Shortly after that I
> ran into a related issue involving genpds when testing v6.2-rc, which again
> took a non-trivial amount of time to track down (and I'm familiar with the SoC
> platform and the general nature of the issue). I don't think it's reasonable
> to expect every user/downstream maintainer of an impacted system to go through
> this, one person at a time.

I think it would be nice to have some way of 'sync_pending' debug
available (compare this to debugfs/devices_deferred).

Note, we are trying to make sure that all supported drivers are enabled
at least as modules (if possible). If we fail, please send a patch
fixing the defconfig.

> Maybe there could be a generic solution for drivers with a 'sync_state'
> callback, e.g. a the driver (or framework) could have a 'sync_state_timeout'
> callback (or similar), which is called by the driver framework if 'sync_state'
> wasn't called (for example) 30s after the device was probed. Then the provider
> can power off or throttle unclaimed resources.

I might be missing a point somewhere, but for me it looks like a logical
solution. Please send a proposal.

--
With best wishes
Dmitry

\
 
 \ /
  Last update: 2023-03-27 00:09    [W:0.163 / U:0.340 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site