lkml.org 
[lkml]   [2023]   [Feb]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v1 3/3] arch/arm: dts: introduce meson-a1 device tree
Date
Add basic support for the 32-bit Amlogic A1. This device tree
describes following compontents: CPU, GIC, IRQ, Timer, UART,
PIN controller. It's capable of booting up into
the serial console.

This is based on arm64 version of meson-a1.dtsi.

Signed-off-by: Alexey Romanov <avromanov@sberdevices.ru>
---
arch/arm/boot/dts/meson-a1.dtsi | 151 ++++++++++++++++++++++++++++++++
1 file changed, 151 insertions(+)
create mode 100644 arch/arm/boot/dts/meson-a1.dtsi

diff --git a/arch/arm/boot/dts/meson-a1.dtsi b/arch/arm/boot/dts/meson-a1.dtsi
new file mode 100644
index 000000000000..1d900fe86f8e
--- /dev/null
+++ b/arch/arm/boot/dts/meson-a1.dtsi
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2023 SberDevices.
+ * Author: Alexey Romanov <avromanov@sberdevices.ru>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/meson-a1-gpio.h>
+
+/ {
+ compatible = "amlogic,a1";
+
+ interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a35";
+ reg = <0x0>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a35";
+ reg = <0x1>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ l2: l2-cache0 {
+ compatible = "cache";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ sm: secure-monitor {
+ compatible = "amlogic,meson-gxbb-sm";
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ apb: bus@fe000000 {
+ compatible = "simple-bus";
+ reg = <0xfe000000 0x1000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xfe000000 0x1000000>;
+
+ reset: reset-controller@0 {
+ compatible = "amlogic,meson-a1-reset";
+ reg = <0x0 0x8c>;
+ #reset-cells = <1>;
+ };
+
+ periphs_pinctrl: pinctrl@400 {
+ compatible = "amlogic,meson-a1-periphs-pinctrl";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gpio: bank@400 {
+ reg = <0x0400 0x003c>,
+ <0x0480 0x0118>;
+ reg-names = "mux", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&periphs_pinctrl 0 0 62>;
+ };
+
+ };
+
+ uart_AO: serial@1c00 {
+ compatible = "amlogic,meson-gx-uart",
+ "amlogic,meson-ao-uart";
+ reg = <0x1c00 0x18>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>, <&xtal>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+ status = "disabled";
+ };
+
+ uart_AO_B: serial@2000 {
+ compatible = "amlogic,meson-gx-uart",
+ "amlogic,meson-ao-uart";
+ reg = <0x2000 0x18>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>, <&xtal>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+ status = "disabled";
+ };
+
+ gpio_intc: interrupt-controller@0440 {
+ compatible = "amlogic,meson-a1-gpio-intc",
+ "amlogic,meson-gpio-intc";
+ reg = <0x0440 0x14>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ amlogic,channel-interrupts =
+ <49 50 51 52 53 54 55 56>;
+ };
+ };
+
+ gic: interrupt-controller@ff901000 {
+ compatible = "arm,gic-400";
+ reg = <0xff901000 0x1000>,
+ <0xff902000 0x2000>,
+ <0xff904000 0x2000>,
+ <0xff906000 0x2000>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ xtal: xtal-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "xtal";
+ #clock-cells = <0>;
+ };
+};
--
2.38.1
\
 
 \ /
  Last update: 2023-03-27 00:32    [W:0.148 / U:0.532 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site