lkml.org 
[lkml]   [2023]   [Jan]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
Subject[PATCH v4 3/3] arm64: dts: qcom: sm6350: Use specific qmpphy compatible
The sc7180 phy compatible works fine for some cases, but it turns out
sm6350 does need proper phy configuration in the driver, so use the
newly added sm6350 compatible.

Because the sm6350 compatible is using the new binding, we need to
change the node quite a bit to match it.

This fixes qmpphy init when no USB cable is plugged in during bootloader
stage.

Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
---
arch/arm64/boot/dts/qcom/sm6350.dtsi | 54 +++++++++++-------------------------
1 file changed, 16 insertions(+), 38 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 8224adb99948..128dbbe23ef5 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -13,6 +13,7 @@
#include <dt-bindings/interconnect/qcom,sm6350.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/phy/phy-qcom-qmp.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>

@@ -1314,49 +1315,26 @@ usb_1_hsphy: phy@88e3000 {
resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
};

- usb_1_qmpphy: phy@88e9000 {
- compatible = "qcom,sc7180-qmp-usb3-dp-phy";
- reg = <0 0x088e9000 0 0x200>,
- <0 0x088e8000 0 0x40>,
- <0 0x088ea000 0 0x200>;
- status = "disabled";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
+ usb_1_qmpphy: phy@88e8000 {
+ compatible = "qcom,sm6350-qmp-usb3-dp-phy";
+ reg = <0 0x088e8000 0 0x3000>;

clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
- <&xo_board>,
- <&rpmhcc RPMH_QLINK_CLK>,
- <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
- clock-names = "aux", "cfg_ahb", "ref", "com_aux";
+ <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
+ <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
+ <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+ clock-names = "aux", "ref", "com_aux", "usb3_pipe";
+
+ power-domains = <&gcc USB30_PRIM_GDSC>;

- resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
- <&gcc GCC_USB3_PHY_PRIM_BCR>;
+ resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
+ <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
reset-names = "phy", "common";

- usb_1_ssphy: usb3-phy@88e9200 {
- reg = <0 0x088e9200 0 0x200>,
- <0 0x088e9400 0 0x200>,
- <0 0x088e9c00 0 0x400>,
- <0 0x088e9600 0 0x200>,
- <0 0x088e9800 0 0x200>,
- <0 0x088e9a00 0 0x100>;
- #clock-cells = <0>;
- #phy-cells = <0>;
- clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
- clock-names = "pipe0";
- clock-output-names = "usb3_phy_pipe_clk_src";
- };
+ #clock-cells = <1>;
+ #phy-cells = <1>;

- dp_phy: dp-phy@88ea200 {
- reg = <0 0x088ea200 0 0x200>,
- <0 0x088ea400 0 0x200>,
- <0 0x088eaa00 0 0x200>,
- <0 0x088ea600 0 0x200>,
- <0 0x088ea800 0 0x200>;
- #phy-cells = <0>;
- #clock-cells = <1>;
- };
+ status = "disabled";
};

dc_noc: interconnect@9160000 {
@@ -1430,7 +1408,7 @@ usb_1_dwc3: usb@a600000 {
snps,dis_enblslpm_quirk;
snps,has-lpm-erratum;
snps,hird-threshold = /bits/ 8 <0x10>;
- phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+ phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>;
phy-names = "usb2-phy", "usb3-phy";
};
};
--
2.39.1

\
 
 \ /
  Last update: 2023-03-26 23:52    [W:1.733 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site