lkml.org 
[lkml]   [2023]   [Jan]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/2] arm64: dts: imx8mp-verdin-dev: Do not include dahlia dtsi
Hi Philippe,

Thank you for the patch.

On Wed, Jan 18, 2023 at 11:52:51AM +0100, Philippe Schenker wrote:
> From: Philippe Schenker <philippe.schenker@toradex.com>
>
> Follow the change that has been done on imx8mm-verdin-dev.dtsi and
> remove the include from dahlia to be consistent. Put back all nodes that
> previously had been included.
>
> Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
>
> ---
>
> .../boot/dts/freescale/imx8mp-verdin-dev.dtsi | 116 +++++++++++++++++-
> 1 file changed, 114 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
> index cefabe65b252..361426c0da0a 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
> @@ -3,8 +3,6 @@
> * Copyright 2022 Toradex
> */
>
> -#include "imx8mp-verdin-dahlia.dtsi"
> -

Makes sense.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> / {
> /* TODO: Audio Codec */
>
> @@ -21,16 +19,99 @@ reg_eth2phy: regulator-eth2phy {
> };
> };
>
> +&backlight {
> + power-supply = <&reg_3p3v>;
> +};
> +
> +/* Verdin SPI_1 */
> +&ecspi1 {
> + status = "okay";
> +};
> +
> +/* EEPROM on display adapter boards */
> +&eeprom_display_adapter {
> + status = "okay";
> +};
> +
> +/* EEPROM on Verdin Development board */
> +&eeprom_carrier_board {
> + status = "okay";
> +};
> +
> +&eqos {
> + status = "okay";
> +};
> +
> &fec {
> phy-supply = <&reg_eth2phy>;
> status = "okay";
> };
>
> +&flexcan1 {
> + status = "okay";
> +};
> +
> +&flexcan2 {
> + status = "okay";
> +};
> +
> +/* Verdin QSPI_1 */
> +&flexspi {
> + status = "okay";
> +};
> +
> &gpio_expander_21 {
> status = "okay";
> vcc-supply = <&reg_1p8v>;
> };
>
> +/* Current measurement into module VCC */
> +&hwmon {
> + status = "okay";
> +};
> +
> +&hwmon_temp {
> + vs-supply = <&reg_1p8v>;
> + status = "okay";
> +};
> +
> +/* Verdin I2C_2_DSI */
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c3 {
> + status = "okay";
> +};
> +
> +/* Verdin I2C_1 */
> +&i2c4 {
> + status = "okay";
> +
> + /* TODO: Audio Codec */
> +};
> +
> +/* TODO: Verdin PCIE_1 */
> +
> +/* Verdin PWM_1 */
> +&pwm1 {
> + status = "okay";
> +};
> +
> +/* Verdin PWM_2 */
> +&pwm2 {
> + status = "okay";
> +};
> +
> +/* Verdin PWM_3_DSI */
> +&pwm3 {
> + status = "okay";
> +};
> +
> +&reg_usdhc2_vmmc {
> + vin-supply = <&reg_3p3v>;
> +};
> +
> /* TODO: Verdin I2C_1 with Audio Codec */
>
> /* Verdin UART_1, connector X50 through RS485 transceiver */
> @@ -38,9 +119,40 @@ &uart1 {
> linux,rs485-enabled-at-boot-time;
> rs485-rts-active-low;
> rs485-rx-during-tx;
> + status = "okay";
> +};
> +
> +/* Verdin UART_2 */
> +&uart2 {
> + status = "okay";
> +};
> +
> +/* Verdin UART_3, used as the Linux Console */
> +&uart3 {
> + status = "okay";
> +};
> +
> +/* Verdin USB_1 */
> +&usb3_0 {
> + status = "okay";
> +};
> +
> +&usb3_phy0 {
> + status = "okay";
> +};
> +
> +/* Verdin USB_2 */
> +&usb3_1 {
> + fsl,permanently-attached;
> + status = "okay";
> +};
> +
> +&usb3_phy1 {
> + status = "okay";
> };
>
> /* Limit frequency on dev board due to long traces and bad signal integrity */
> &usdhc2 {
> max-frequency = <100000000>;
> + status = "okay";
> };

--
Regards,

Laurent Pinchart

\
 
 \ /
  Last update: 2023-03-26 23:46    [W:0.097 / U:0.256 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site