lkml.org 
[lkml]   [2022]   [Sep]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] phy: marvell: phy-mvebu-a3700-comphy: Reset COMPHY registers before USB 3.0 power on
On Saturday 24 September 2022 10:31:27 Pali Rohár wrote:
> On Saturday 24 September 2022 12:44:49 Vinod Koul wrote:
> > On 21-09-22, 10:05, Pali Rohár wrote:
> > > On Wednesday 21 September 2022 05:03:01 Shinichiro Kawasaki wrote:
> > > > On Sep 20, 2022 / 14:11, Pali Rohár wrote:
> > > > > Turris MOX board with older ARM Trusted Firmware version v1.5 is not able
> > > > > to detect any USB 3.0 device connected to USB-A port on Mox-A module after
> > > > > commit 0a6fc70d76bd ("phy: marvell: phy-mvebu-a3700-comphy: Remove broken
> > > > > reset support"). On the other hand USB 2.0 devices connected to the same
> > > > > USB-A port are working fine.
> > > > >
> > > > > It looks as if the older firmware configures COMPHY registers for USB 3.0
> > > > > somehow incompatibly for kernel driver. Experiments show that resetting
> > > > > COMPHY registers via setting SFT_RST auto-clearing bit in COMPHY_SFT_RESET
> > > > > register fixes this issue.
> > > > >
> > > > > Reset the COMPHY in mvebu_a3700_comphy_usb3_power_on() function as a first
> > > > > step after selecting COMPHY lane and USB 3.0 function. With this change
> > > > > Turris MOX board can successfully detect USB 3.0 devices again.
> > > > >
> > > > > Before the above mentioned commit this reset was implemented in PHY reset
> > > > > method, so this is the reason why there was no issue with older firmware
> > > > > version then.
> > > > >
> > > > > Fixes: 0a6fc70d76bd ("phy: marvell: phy-mvebu-a3700-comphy: Remove broken reset support")
> > > > > Reported-by: Marek Behún <kabel@kernel.org>
> > > > > Signed-off-by: Pali Rohár <pali@kernel.org>
> > > > > ---
> > > > > Shinichiro, could you please check that all USB functionality still
> > > > > works correctly on your board?
> > > > > ---
> > > >
> > > > Sure. TL;DR, this patch works ok for my espressobin v7 board.
> > > >
> > > > Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
> > > >
> > > > I prepared base kernel v5.19.10 applying the commit 0a6fc70d76bd. Regardless
> > > > whether this fix patch for Turrix MOX board is applied or not, two USB ports on
> > > > my esprssobin v7 board worked as expected. I confirmed it by using USB thumb
> > > > drive. The drive was detected and its partition was mounted successfully using
> > > > either of the two USB ports.
> > >
> > > Thank you for testing! Anyway, please check that USB 3.0 device is
> > > working fine. Because as I wrote in commit message, on Turris Mox was
> > > USB 2.0 device working fine, but USB 3.0 not. And maybe check in system
> >
> > update the log now?
>
> What do you want to update?

Vinod, could you describe a bit more what is needed to update? Because
this patch fixes regression - USB 3.0 support on Turris Mox board.

> > > (lsusb) that USB 3.0 device was really detected as USB 3.0 because USB
> > > 3.0 devices have supported also fallback USB 2.0/1.x legacy mode.
> > >
> > > > I also confirmed SATA port is ok (my SSD card was detected without error
> > > > message) and three network ports works ok ("Link is Up" message on network cable
> > > > connection). I did same confirmations with the latest firmware (TF-A and U-boot)
> > > > and old firmware (with version date in 2017). All looks good for me.
> > > >
> > > > --
> > > > Shin'ichiro Kawasaki
> >
> > --
> > ~Vinod

\
 
 \ /
  Last update: 2022-10-01 01:47    [W:0.083 / U:0.340 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site