lkml.org 
[lkml]   [2022]   [Sep]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v1 2/2] dt-bindings: add bindings for QCOM flash LED
From
On 28/09/2022 04:42, Fenglin Wu wrote:
> Add binding document for flash LED module inside Qualcomm Technologies,
> Inc. PMICs.
>
> Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>

You did not Cc me on first patch, so difficult to say how much it
matches the driver... There is also no DTS.

> ---
> .../bindings/leds/leds-qcom-flash.yaml | 108 ++++++++++++++++++
> 1 file changed, 108 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/leds/leds-qcom-flash.yaml
>
> diff --git a/Documentation/devicetree/bindings/leds/leds-qcom-flash.yaml b/Documentation/devicetree/bindings/leds/leds-qcom-flash.yaml
> new file mode 100644
> index 000000000000..52a99182961b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/leds/leds-qcom-flash.yaml


Filename matching compatible if there is one fallback (e.g.
qcom,spmi-flash-led.yaml).

> @@ -0,0 +1,108 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/leds/leds-qcom-flash.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Flash LED device inside Qualcomm Technologies, Inc. PMICs
> +
> +maintainers:
> + - Fenglin Wu <quic_fenglinw@quicinc.com>
> +
> +description: |
> + Flash LED controller is present inside some Qualcomm Technologies, Inc. PMICs.
> + The flash LED module can have different number of LED channels supported
> + e.g. 3 or 4. There are some different registers between them but they can
> + both support maximum current up to 1.5 A per channel and they can also support
> + ganging 2 channels together to supply maximum current up to 2 A. The current
> + will be split symmetrically on each channel and they will be enabled and
> + disabled at the same time.
> +
> +properties:
> + compatible:
> + items:
> + - enum:
> + - qcom,spmi-flash-led
> + - qcom,pm8150c-flash-led
> + - qcom,pm8150l-flash-led
> + - qcom,pm8350c-flash-led

I doubt these are all different. You should use fallback, which also
will make use of the "items" you used...

> +
> + reg:
> + description: address offset of the flash LED controller
> + maxItems: 1
> +
> +patternProperties:
> + "^led@[0-3]$":
> + type: object
> + $ref: common.yaml#
> + unevaluatedProperties: false
> + description:
> + Represents the physical LED components which are connected to the flash LED channels' output.

Does not look like wrapped at 80.

Other places as well.

> +
> + properties:

Does not look like you tested the bindings...

You miss here reg.

> + led-sources:
> + description: The HW indices of the flash LED channels that connect to the physical LED
> + allOf:
> + - minItems: 1
> + maxItems: 2
> + items:
> + enum: [1, 2, 3, 4]
> +
> + led-max-microamp:
> + description: |
> + The maximum current value when LED is not operating in flash mode (i.e. torch mode)
> + Valid values when an LED is connected to one flash LED channel:
> + 5000 - 500000, step by 5000> + Valid values when an LED is connected to two flash LED
channels:
> + 10000 - 1000000, step by 10000

You need minimum and maximum.

> +
> + flash-max-microamp:
> + description: |
> + The maximum current value when LED is operating in flash mode.
> + Valid values when an LED is connected to one flash LED channel:
> + 12500 - 1500000, step by 12500
> + Valid values when an LED is connected to two flash LED channels:
> + 25000 - 2000000, step by 12500

You need minimum and maximum.


> +
> + flash-max-timeout-us:
> + description: |
> + The maximum timeout value when LED is operating in flash mode.
> + Valid values: 10000 - 1280000, step by 10000

You need minimum and maximum.

> +
> + required:
> + - led-sources
> + - led-max-microamp

reg.

> +
> +required:
> + - compatible
> + - reg
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/leds/common.h>
> + flash-led@ee00 {

Node name: led-controller

> + compatible = "qcom,spmi-flash-led";
> + reg = <0xee00>;
> +
> + led@0 {

Test your bindings...

> + function = LED_FUNCTION_FLASH;

Use 4 spaces for indentation of example.

> + color = <LED_COLOR_ID_WHITE>;
> + led-sources = <1>, <4>;
> + led-max-microamp = <300000>;
> + flash-max-microamp = <2000000>;
> + flash-max-timeout-us = <1280000>;
> + function-enumerator = <0>;
> + };
> +

Best regards,
Krzysztof

\
 
 \ /
  Last update: 2022-09-28 10:23    [W:0.073 / U:0.296 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site