lkml.org 
[lkml]   [2022]   [Sep]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
SubjectRe: [PATCH] ARM: dts: Add Raspberry Pi Compute Module 4 CANOPi Board
From
Hi Alexander,

[fix address of Krzysztof]

Am 19.09.22 um 09:47 schrieb Alexander Dahl:
> Hei hei,
>
> Am Fri, Sep 16, 2022 at 12:31:56PM -0300 schrieb Ariel D'Alessandro:
>> The Eclipse KUKSA CANOPi [0] is a baseboard for the Raspberry Compute
>> Module 4 (CM4). It contains a VIA VL805 4 Port USB controller and two
>> MCP251xFD based CAN-FD interfaces.
>>
>> [0] https://github.com/boschresearch/kuksa.hardware
>>
>> Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
>> ---
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/bcm2711-rpi-cm4-canopi.dts | 139 ++++++++++++++++++
>> arch/arm64/boot/dts/broadcom/Makefile | 1 +
>> .../dts/broadcom/bcm2711-rpi-cm4-canopi.dts | 2 +
>> 4 files changed, 143 insertions(+)
>> create mode 100644 arch/arm/boot/dts/bcm2711-rpi-cm4-canopi.dts
>> create mode 100644 arch/arm64/boot/dts/broadcom/bcm2711-rpi-cm4-canopi.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 05d8aef6e5d2..8930ab2c132c 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -98,6 +98,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
>> bcm2837-rpi-zero-2-w.dtb \
>> bcm2711-rpi-400.dtb \
>> bcm2711-rpi-4-b.dtb \
>> + bcm2711-rpi-cm4-canopi.dtb \
>> bcm2711-rpi-cm4-io.dtb \
>> bcm2835-rpi-zero.dtb \
>> bcm2835-rpi-zero-w.dtb
>> diff --git a/arch/arm/boot/dts/bcm2711-rpi-cm4-canopi.dts b/arch/arm/boot/dts/bcm2711-rpi-cm4-canopi.dts
>> new file mode 100644
>> index 000000000000..52ec5908883c
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/bcm2711-rpi-cm4-canopi.dts
>> @@ -0,0 +1,139 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/dts-v1/;
>> +#include "bcm2711-rpi-cm4.dtsi"
>> +
>> +/ {
>> + model = "Raspberry Pi Compute Module 4 CANOPi Board";
>> +
>> + clocks {
>> + clk_mcp251xfd_osc: mcp251xfd-osc {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <20000000>;
>> + };
>> + };
>> +
>> + leds {
>> + led-act {
>> + gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
>> + };
>> +
>> + led-pwr {
>> + label = "PWR";
>> + gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
>> + default-state = "keep";
>> + linux,default-trigger = "default-on";
>> + };
>> + };
> This looks like using the node name and the deprecated "label"
> property for LED naming. Please see
> Documentation/devicetree/bindings/leds/common.yaml and use the
> properties "function" and "color" instead. Also check the node names
> itself, see the example in that binding or the leds-gpio binding for
> reference.

Oops, i didn't noticed this.

Unfortunately the ACT-LED is already a little bit opaque defined in
bcm2835-rpi.dtsi:

leds {
        compatible = "gpio-leds";

        led-act {
            label = "ACT";
            default-state = "keep";
            linux,default-trigger = "heartbeat";
        };
};

So a reference (currently missing) would have make it clear that the
ACT-LED is common for all Raspberry Pi boards.

So you wish that this is fixed for the CANOPi board or all Raspberry Pi
boards?

I'm asking because switching to function would change the sysfs path and
breaking userspace ABI.

>
> Greets
> Alex
>
>> +};
>> +
>> +&ddc0 {
>> + status = "okay";
>> +};
>> +
>> +&ddc1 {
>> + status = "okay";
>> +};
>> +
>> +&hdmi0 {
>> + status = "okay";
>> +};
>> +
>> +&hdmi1 {
>> + status = "okay";
>> +};
>> +
>> +&i2c0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&i2c0_gpio44>;
>> + status = "okay";
>> + clock-frequency = <100000>;
>> +
>> + pcf85063a@51 {
>> + compatible = "nxp,pcf85063a";
>> + reg = <0x51>;
>> + };
>> +};
>> +
>> +&pcie0 {
>> + pci@0,0 {
>> + device_type = "pci";
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> + ranges;
>> +
>> + reg = <0 0 0 0 0>;
>> +
>> + usb@0,0 {
>> + reg = <0 0 0 0 0>;
>> + resets = <&reset RASPBERRYPI_FIRMWARE_RESET_ID_USB>;
>> + };
>> + };
>> +};
>> +
>> +&pixelvalve0 {
>> + status = "okay";
>> +};
>> +
>> +&pixelvalve1 {
>> + status = "okay";
>> +};
>> +
>> +&pixelvalve2 {
>> + status = "okay";
>> +};
>> +
>> +&pixelvalve4 {
>> + status = "okay";
>> +};
>> +
>> +&spi {
>> + status = "okay";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&spi0_gpio7>;
>> + cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
>> + dmas = <&dma 6>, <&dma 7>;
>> + dma-names = "tx", "rx";
>> +
>> + mcp251xfd0: mcp251xfd@0 {
>> + compatible = "microchip,mcp251xfd";
>> + reg = <0>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mcp251xfd0_pins>;
>> + spi-max-frequency = <20000000>;
>> + interrupt-parent = <&gpio>;
>> + interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
>> + clocks = <&clk_mcp251xfd_osc>;
>> + };
>> +
>> + mcp251xfd1: mcp251xfd@1 {
>> + compatible = "microchip,mcp251xfd";
>> + reg = <1>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mcp251xfd1_pins>;
>> + spi-max-frequency = <20000000>;
>> + interrupt-parent = <&gpio>;
>> + interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
>> + clocks = <&clk_mcp251xfd_osc>;
>> + };
>> +};
>> +
>> +&gpio {
>> + mcp251xfd0_pins: mcp251xfd0_pins {
>> + brcm,pins = <27>;
>> + brcm,function = <BCM2835_FSEL_GPIO_IN>;
>> + };
>> +
>> + mcp251xfd1_pins: mcp251xfd1_pins {
>> + brcm,pins = <22>;
>> + brcm,function = <BCM2835_FSEL_GPIO_IN>;
>> + };
>> +};
>> +
>> +&vc4 {
>> + status = "okay";
>> +};
>> +
>> +&vec {
>> + status = "disabled";
>> +};
>> diff --git a/arch/arm64/boot/dts/broadcom/Makefile b/arch/arm64/boot/dts/broadcom/Makefile
>> index e8584d3b698f..7cd88b8c0345 100644
>> --- a/arch/arm64/boot/dts/broadcom/Makefile
>> +++ b/arch/arm64/boot/dts/broadcom/Makefile
>> @@ -1,6 +1,7 @@
>> # SPDX-License-Identifier: GPL-2.0
>> dtb-$(CONFIG_ARCH_BCM2835) += bcm2711-rpi-400.dtb \
>> bcm2711-rpi-4-b.dtb \
>> + bcm2711-rpi-cm4-canopi.dtb \
>> bcm2711-rpi-cm4-io.dtb \
>> bcm2837-rpi-3-a-plus.dtb \
>> bcm2837-rpi-3-b.dtb \
>> diff --git a/arch/arm64/boot/dts/broadcom/bcm2711-rpi-cm4-canopi.dts b/arch/arm64/boot/dts/broadcom/bcm2711-rpi-cm4-canopi.dts
>> new file mode 100644
>> index 000000000000..e9369aa0eb39
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/broadcom/bcm2711-rpi-cm4-canopi.dts
>> @@ -0,0 +1,2 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +#include "arm/bcm2711-rpi-cm4-canopi.dts"
>> --
>> 2.37.2

\
 
 \ /
  Last update: 2022-09-19 13:19    [W:0.644 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site