lkml.org 
[lkml]   [2022]   [Sep]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH 1/6] dt-bindings: phy: ti: phy-gmii-sel: Add bindings for J721e
From
On 14/09/2022 11:39, Siddharth Vadapalli wrote:
> TI's J721e SoC supports additional PHY modes like QSGMII and SGMII
> that are not supported on earlier SoCs. Add a compatible for it.
>
> Extend ti,qsgmii-main-ports property to support selection of upto
> two main ports at once across the two QSGMII interfaces.
>
> Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
> ---
> .../bindings/phy/ti,phy-gmii-sel.yaml | 52 ++++++++++++++++---
> 1 file changed, 46 insertions(+), 6 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml b/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml
> index da7cac537e15..1e19efab018b 100644
> --- a/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml
> +++ b/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml
> @@ -54,6 +54,7 @@ properties:
> - ti,dm814-phy-gmii-sel
> - ti,am654-phy-gmii-sel
> - ti,j7200-cpsw5g-phy-gmii-sel
> + - ti,j721e-cpsw9g-phy-gmii-sel
>
> reg:
> maxItems: 1
> @@ -65,12 +66,19 @@ properties:
> description: |
> Required only for QSGMII mode. Array to select the port for
> QSGMII main mode. Rest of the ports are selected as QSGMII_SUB
> - ports automatically. Any one of the 4 CPSW5G ports can act as the
> - main port with the rest of them being the QSGMII_SUB ports.
> - maxItems: 1
> - items:
> - minimum: 1
> - maximum: 4

minItems: 1
maxItems: 2
items:
minimum: 1
maximum: 8

> + ports automatically. For J7200 CPSW5G with the compatible:
> + ti,j7200-cpsw5g-phy-gmii-sel, ti,qsgmii-main-ports is an
> + array of only one element, which is the port number ranging from
> + 1 to 4. For J721e CPSW9G with the compatible:
> + ti,j721e-cpsw9g-phy-gmii-sel, ti,qsgmii-main-ports is an array
> + of two elements, which corresponds to two potential QSGMII main
> + ports. The first element and second element of the array can both
> + range from 1 to 8 each, corresponding to two QSGMII main ports.
> + For J721e CPSW9G, to configure port 2 as the first QSGMII main
> + port and port 7 as the second QSGMII main port, we specify:
> + ti,qsgmii-main-ports = <2>, <7>;
> + If only one QSGMII main port is desired, mention the same main
> + port twice.
>
> allOf:
> - if:
> @@ -81,12 +89,43 @@ allOf:
> - ti,dra7xx-phy-gmii-sel
> - ti,dm814-phy-gmii-sel
> - ti,am654-phy-gmii-sel
> + - ti,j7200-cpsw5g-phy-gmii-sel
> + - ti,j721e-cpsw9g-phy-gmii-sel
> then:
> properties:
> '#phy-cells':
> const: 1
> description: CPSW port number (starting from 1)
>
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - ti,j7200-cpsw5g-phy-gmii-sel
> + then:
> + properties:
> + ti,qsgmii-main-ports:
> + maxItems: 1
> + items:
> + minimum: 1
> + maximum: 4
> +
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - ti,j721e-cpsw9g-phy-gmii-sel
> + then:
> + properties:
> + ti,qsgmii-main-ports:
> + minItems: 2
> + maxItems: 2
> + items:
> + minimum: 1
> + maximum: 8
> +
> - if:
> not:
> properties:
> @@ -94,6 +133,7 @@ allOf:
> contains:
> enum:
> - ti,j7200-cpsw5g-phy-gmii-sel
> + - ti,j721e-cpsw9g-phy-gmii-sel
> then:
> properties:
> ti,qsgmii-main-ports: false

This is interesting here... Did you test the bindings with your DTS?


Best regards,
Krzysztof

\
 
 \ /
  Last update: 2022-09-19 12:16    [W:1.261 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site