lkml.org 
[lkml]   [2022]   [Aug]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v1 2/2] serial: pic32_uart: Convert to use GPIO descriptors
Date
Plain global GPIO numbering schema is deprecated and is being removed
from the kernel. Convert this driver to use a new GPIO descriptor based
schema.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
drivers/tty/serial/pic32_uart.c | 48 +++++++++------------------------
1 file changed, 12 insertions(+), 36 deletions(-)

diff --git a/drivers/tty/serial/pic32_uart.c b/drivers/tty/serial/pic32_uart.c
index 1562c2a48467..56516a72d661 100644
--- a/drivers/tty/serial/pic32_uart.c
+++ b/drivers/tty/serial/pic32_uart.c
@@ -50,7 +50,7 @@
* @irq_rx_name: irq rx name
* @irq_tx: virtual tx interrupt number
* @irq_tx_name: irq tx name
- * @cts_gpio: clear to send gpio
+ * @cts_gpiod: clear to send GPIO
* @dev: device descriptor
**/
struct pic32_sport {
@@ -65,8 +65,7 @@ struct pic32_sport {
const char *irq_tx_name;
bool enable_tx_irq;

- bool hw_flow_ctrl;
- int cts_gpio;
+ struct gpio_desc *cts_gpiod;

struct clk *clk;

@@ -158,25 +157,16 @@ static void pic32_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
PIC32_UART_MODE_LPBK);
}

-/* get the state of CTS input pin for this port */
-static unsigned int get_cts_state(struct pic32_sport *sport)
-{
- /* read and invert UxCTS */
- if (gpio_is_valid(sport->cts_gpio))
- return !gpio_get_value(sport->cts_gpio);
-
- return 1;
-}
-
/* serial core request to return the state of misc UART input pins */
static unsigned int pic32_uart_get_mctrl(struct uart_port *port)
{
struct pic32_sport *sport = to_pic32_sport(port);
unsigned int mctrl = 0;

- if (!sport->hw_flow_ctrl)
+ /* get the state of CTS input pin for this port */
+ if (!sport->cts_gpiod)
mctrl |= TIOCM_CTS;
- else if (get_cts_state(sport))
+ else if (gpiod_get_value(sport->cts_gpiod))
mctrl |= TIOCM_CTS;

/* DSR and CD are not supported in PIC32, so return 1
@@ -648,7 +638,7 @@ static void pic32_uart_set_termios(struct uart_port *port,
PIC32_UART_MODE_PDSEL0);
}
/* if hw flow ctrl, then the pins must be specified in device tree */
- if ((new->c_cflag & CRTSCTS) && sport->hw_flow_ctrl) {
+ if ((new->c_cflag & CRTSCTS) && sport->cts_gpiod) {
/* enable hardware flow control */
pic32_uart_writel(sport, PIC32_SET(PIC32_UART_MODE),
PIC32_UART_MODE_UEN1);
@@ -875,7 +865,8 @@ static struct uart_driver pic32_uart_driver = {

static int pic32_uart_probe(struct platform_device *pdev)
{
- struct device_node *np = pdev->dev.of_node;
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
struct pic32_sport *sport;
int uart_idx = 0;
struct resource *res_mem;
@@ -904,25 +895,10 @@ static int pic32_uart_probe(struct platform_device *pdev)
/* Hardware flow control: gpios
* !Note: Basically, CTS is needed for reading the status.
*/
- sport->hw_flow_ctrl = false;
- sport->cts_gpio = of_get_named_gpio(np, "cts-gpios", 0);
- if (gpio_is_valid(sport->cts_gpio)) {
- sport->hw_flow_ctrl = true;
-
- ret = devm_gpio_request(sport->dev,
- sport->cts_gpio, "CTS");
- if (ret) {
- dev_err(&pdev->dev,
- "error requesting CTS GPIO\n");
- goto err;
- }
-
- ret = gpio_direction_input(sport->cts_gpio);
- if (ret) {
- dev_err(&pdev->dev, "error setting CTS GPIO\n");
- goto err;
- }
- }
+ sport->cts_gpiod = devm_gpiod_get_optional(dev, "cts", GPIOD_IN);
+ if (IS_ERR(sport->cts_gpiod))
+ return dev_err_probe(dev, PTR_ERR(sport->cts_gpiod), "error requesting CTS GPIO\n");
+ gpiod_set_consumer_name(sport->cts_gpiod, "CTS");

pic32_sports[uart_idx] = sport;
port = &sport->port;
--
2.35.1
\
 
 \ /
  Last update: 2022-08-07 00:57    [W:0.044 / U:0.124 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site