lkml.org 
[lkml]   [2022]   [May]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [v4 1/3] dt-bindings: phy: qcom,usb-snps-femto-v2: Add phy override params bindings
From
On 11/05/2022 17:26, Krishna Kurapati wrote:
> From: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
>
> Add device tree bindings for SNPS phy tuning parameters.
>
> Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
> Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
> ---
> .../bindings/phy/qcom,usb-snps-femto-v2.yaml | 87 ++++++++++++++++++++++
> 1 file changed, 87 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
> index 1ce251d..70efffe 100644
> --- a/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
> +++ b/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
> @@ -53,6 +53,93 @@ properties:
> vdda33-supply:
> description: phandle to the regulator 3.3V supply node.
>
> + qcom,hs-disconnect-bps:
> + $ref: /schemas/types.yaml#/definitions/int32
> + description:
> + This adjusts the voltage level for the threshold used to
> + detect a disconnect event at the host. Possible values are.
> + The values defined are in multiples of basis points (1bp = 0.01%).

This means there is some minimum and maximum (100%)?

> + The hardware accepts only discrete values. The value closest to the
> + provided input will be chosen as the override value for this param.
> +
> + qcom,squelch-detector-bps:
> + $ref: /schemas/types.yaml#/definitions/int32
> + description:
> + This adjusts the voltage level for the threshold used to
> + detect valid high-speed data.
> + The values defined are in multiples of basis points (1bp = 0.01%).
> + The hardware accepts only discrete values. The value closest to the
> + provided input will be chosen as the override value for this param.
> +
> + qcom,hs-amplitude-bps:
> + $ref: /schemas/types.yaml#/definitions/int32
> + description:
> + This adjusts the high-speed DC level voltage.
> + The values defined are in multiples of basis points (1bp = 0.01%).
> + The hardware accepts only discrete values. The value closest to the
> + provided input will be chosen as the override value for this param.
> +
> + qcom,pre-emphasis-duration-bps:
> + $ref: /schemas/types.yaml#/definitions/int32
> + description:
> + This signal controls the duration for which the
> + HS pre-emphasis current is sourced onto DP<#> or DM<#>.
> + The HS Transmitter pre-emphasis duration is defined in terms of
> + unit amounts. One unit of pre-emphasis duration is approximately
> + 650 ps and is defined as 1X pre-emphasis duration.
> + The values defined are in multiples of basis points (1bp = 0.01%).
> + The hardware accepts only discrete values. The value closest to the
> + provided input will be chosen as the override value for this param.
> +
> + qcom,pre-emphasis-amplitude-bps:
> + $ref: /schemas/types.yaml#/definitions/int32
> + description:
> + This signal controls the amount of current sourced to
> + DP<#> and DM<#> after a J-to-K or K-to-J transition.
> + The HS Transmitter pre-emphasis current is defined in terms of unit
> + amounts. One unit amount is approximately 2 mA and is defined as
> + 1X pre-emphasis current.
> + The values defined are in multiples of basis points (1bp = 0.01%).
> + The hardware accepts only discrete values. The value closest to the
> + provided input will be chosen as the override value for this param.
> +
> + qcom,hs-rise-fall-time-bps:
> + $ref: /schemas/types.yaml#/definitions/int32
> + description:
> + This adjusts the rise/fall times of the high-speed waveform.
> + The values defined are in multiples of basis points (1bp = 0.01%).
> + The hardware accepts only discrete values. The value closest to the
> + provided input will be chosen as the override value for this param.
> +
> + qcom,hs-crossover-voltage-mv:
> + $ref: /schemas/types.yaml#/definitions/int32
> + description:
> + This adjusts the voltage at which the DP<#> and DM<#>
> + signals cross while transmitting in HS mode.
> + The values defined are in milli volts. The hardware accepts only
> + discrete values. The value closest to the provided input will be
> + chosen as the override value for this param.
> +
> + qcom,hs-output-impedance-mohm:
> + $ref: /schemas/types.yaml#/definitions/int32

Here and in other places, please use standard units. See
dtschema/schemas/property-units.yaml in dtschema repo.


Best regards,
Krzysztof

\
 
 \ /
  Last update: 2022-05-11 20:21    [W:0.254 / U:0.440 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site