lkml.org 
[lkml]   [2022]   [Apr]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/3] arm64: dts: qcom: sm8350: Add GENI I2C/SPI DMA channels
On 12-04-22, 20:57, Bjorn Andersson wrote:
> On Tue 12 Apr 20:14 PDT 2022, Vinod Koul wrote:
>
> > On 12-04-22, 14:51, Bjorn Andersson wrote:
> > > The GENI I2C and SPI controllers may use the GPI DMA engine, define the
> > > rx and tx channels for these controllers to enable this.
> > >
> > > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> > > ---
> > > arch/arm64/boot/dts/qcom/sm8350.dtsi | 108 +++++++++++++++++++++++++++
> > > 1 file changed, 108 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> > > index 7e585d9e4c68..8547c0b2f060 100644
> > > --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
> > > +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> > > @@ -721,6 +721,9 @@ i2c14: i2c@880000 {
> > > pinctrl-names = "default";
> > > pinctrl-0 = <&qup_i2c14_default>;
> > > interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
> > > + dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>,
> > > + <&gpi_dma2 1 0 QCOM_GPI_I2C>;
> > > + dma-names = "tx", "rx";
> >
> > I have been thinking about this. I dont feel this is right approach here
> > as this is board dependent and having the firmware loaded on the board..
> >
> > This was tested on HDK and can fail in MTP or other boards.. which might
> > be in FIFO mode
> >
>
> But if the controller is in FIFO mode, then !fifo_disable so we wouldn't
> try to pick up the dmas. And in the opposite case, i.e. when
> fifo_disable, the introduction of the GPI implementation meant that the
> i2c driver wouldn't no longer probe without the dmas specified.
>
> Unfortunately we don't have any i2c busses enabled on the MTP currently,
> so I'm not able to validate this easily.
>
>
> For the SPI driver though, the same logic is used to invoke
> spi_geni_grab_gpi_chan(). So dmas will only be considered if
> fifo_disabled is set.

Right, I tested that and it works just fine. So lets go ahead with this
approach

> That said, in the even that the SPI driver finds a fifo_disabled
> controller and dma_request_chan() returns an error, we will fall back to
> fifo mode instead. I'm not sure if that's desirable...

I agree, we should not fall back, that does not make sense at all

--
~Vinod

\
 
 \ /
  Last update: 2022-04-18 09:20    [W:0.091 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site