lkml.org 
[lkml]   [2022]   [Mar]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: Intermittent performance regression related to ipset between 5.10 and 5.15
From
[TLDR: I'm adding the regression report below to regzbot, the Linux
kernel regression tracking bot; all text you find below is compiled from
a few templates paragraphs you might have encountered already already
from similar mails.]

On 16.03.22 00:15, McLean, Patrick wrote:
> When we upgraded from the 5.10 (5.10.61) series to the 5.15 (5.15.16) series, we encountered an intermittent performance regression that appears to be related to iptables / ipset. This regression was noticed on Kubernetes hosts that run kube-router and experience a high amount of churn to both iptables and ipsets. Specifically, when we run the nftables (iptables-1.8.7 / nftables-1.0.0) iptables wrapper xtables-nft-multi on the 5.15 series kernel, we end up getting extremely laggy response times when iptables attempts to lookup information on the ipsets that are used in the iptables definition. This issue isn’t reproducible on all hosts. However, our experience has been that across a fleet of ~50 hosts we experienced this issue on ~40% of the hosts. When the problem evidences, the time that it takes to run unrestricted iptables list commands like iptables -L or iptables-save gradually increases over the course of about 1 - 2 hours. Growing from less than a second to run, to taking sometimes over 2 minutes to run. After that 2 hour mark it seems to plateau and not grow any longer. Flushing tables or ipsets doesn’t seem to have any affect on the issue. However, rebooting the host does reset the issue. Occasionally, a machine that was evidencing the problem may no longer evidence it after being rebooted.
>
> We did try to debug this to find a root cause, but ultimately ran short on time. We were not able to perform a set of bisects to hopefully narrow down the issue as the problem isn’t consistently reproducible. We were able to get some straces where it appears that most of the time is spent on getsockopt() operations. It appears that during iptables operations, it attempts to do some work to resolve the ipsets that are linked to the iptables definitions (perhaps getting the names of the ipsets themselves?). Slowly that getsockopt request takes more and more time on affected hosts. Here is an example strace of the operation in question:
>
> 0.000074 newfstatat(AT_FDCWD, "/etc/nsswitch.conf", {st_mode=S_IFREG|0644, st_size=539, ...}, 0) = 0 <0.000017>
> 0.000064 openat(AT_FDCWD, "/var/db/protocols.db", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory) <0.000017>
> 0.000057 openat(AT_FDCWD, "/etc/protocols", O_RDONLY|O_CLOEXEC) = 4 <0.000013>
> 0.000034 newfstatat(4, "", {st_mode=S_IFREG|0644, st_size=6108, ...}, AT_EMPTY_PATH) = 0 <0.000009>
> 0.000032 lseek(4, 0, SEEK_SET) = 0 <0.000008>
> 0.000025 read(4, "# /etc/protocols\n#\n# Internet (I"..., 4096) = 4096 <0.000010>
> 0.000036 close(4) = 0 <0.000008>
> 0.000028 write(1, "ANGME7BF25 - [0:0]\n:KUBE-POD-FW-"..., 4096) = 4096 <0.000028>
> 0.000049 socket(AF_INET, SOCK_RAW, IPPROTO_RAW) = 4 <0.000015>
> 0.000032 fcntl(4, F_SETFD, FD_CLOEXEC) = 0 <0.000008>
> 0.000024 getsockopt(4, SOL_IP, 0x53 /* IP_??? */, "\0\1\0\0\7\0\0\0", [8]) = 0 <0.000024>
> 0.000046 getsockopt(4, SOL_IP, 0x53 /* IP_??? */, "\7\0\0\0\7\0\0\0KUBE-DST-VBH27M7NWLDOZIE"..., [40]) = 0 <0.109384>
> 0.109456 close(4) = 0 <0.000022>
>
> On a host that is not evidencing the performance regression we normally see that operation take ~ 0.00001 as opposed to 0.109384.Additionally, hosts that were evidencing the problem we also saw high lock times with `klockstat` (unfortunately at the time we did not know about or run echo "0" > /proc/sys/kernel/kptr_restrict to get the callers of the below commands).
>
> klockstat -i 5 -n 10 (on a host experiencing the problem)
> Caller Avg Hold Count Max hold Total hold
> b'[unknown]' 118490772 83 179899470 9834734132
> b'[unknown]' 118416941 83 179850047 9828606138
> # or somewhere later while iptables -vnL was running:
> Caller Avg Hold Count Max hold Total hold
> b'[unknown]' 496466236 46 17919955720 22837446860
> b'[unknown]' 496391064 46 17919893843 22833988950
>
> klockstat -i 5 -n 10 (on a host not experiencing the problem)
> Caller Avg Hold Count Max hold Total hold
> b'[unknown]' 120316 1510 85537797 181677885
> b'[unknown]' 7119070 24 85527251 170857690

Hi, this is your Linux kernel regression tracker.

Thanks for the report.

CCing the regression mailing list, as it should be in the loop for all
regressions, as explained here:
https://www.kernel.org/doc/html/latest/admin-guide/reporting-issues.html

To be sure below issue doesn't fall through the cracks unnoticed, I'm
adding it to regzbot, my Linux kernel regression tracking bot:

#regzbot ^introduced v5.10..v5.15
#regzbot title net: netfilter: Intermittent performance regression
related to ipset
#regzbot ignore-activity

If it turns out this isn't a regression, free free to remove it from the
tracking by sending a reply to this thread containing a paragraph like
"#regzbot invalid: reason why this is invalid" (without the quotes).

Reminder for developers: when fixing the issue, please add a 'Link:'
tags pointing to the report (the mail quoted above) using
lore.kernel.org/r/, as explained in
'Documentation/process/submitting-patches.rst' and
'Documentation/process/5.Posting.rst'. Regzbot needs them to
automatically connect reports with fixes, but they are useful in
general, too.

I'm sending this to everyone that got the initial report, to make
everyone aware of the tracking. I also hope that messages like this
motivate people to directly get at least the regression mailing list and
ideally even regzbot involved when dealing with regressions, as messages
like this wouldn't be needed then. And don't worry, if I need to send
other mails regarding this regression only relevant for regzbot I'll
send them to the regressions lists only (with a tag in the subject so
people can filter them away). With a bit of luck no such messages will
be needed anyway.

Ciao, Thorsten (wearing his 'the Linux kernel's regression tracker' hat)

P.S.: As the Linux kernel's regression tracker I'm getting a lot of
reports on my table. I can only look briefly into most of them and lack
knowledge about most of the areas they concern. I thus unfortunately
will sometimes get things wrong or miss something important. I hope
that's not the case here; if you think it is, don't hesitate to tell me
in a public reply, it's in everyone's interest to set the public record
straight.

--
Additional information about regzbot:

If you want to know more about regzbot, check out its web-interface, the
getting start guide, and the references documentation:

https://linux-regtracking.leemhuis.info/regzbot/
https://gitlab.com/knurd42/regzbot/-/blob/main/docs/getting_started.md
https://gitlab.com/knurd42/regzbot/-/blob/main/docs/reference.md

The last two documents will explain how you can interact with regzbot
yourself if your want to.

Hint for reporters: when reporting a regression it's in your interest to
CC the regression list and tell regzbot about the issue, as that ensures
the regression makes it onto the radar of the Linux kernel's regression
tracker -- that's in your interest, as it ensures your report won't fall
through the cracks unnoticed.

Hint for developers: you normally don't need to care about regzbot once
it's involved. Fix the issue as you normally would, just remember to
include 'Link:' tag in the patch descriptions pointing to all reports
about the issue. This has been expected from developers even before
regzbot showed up for reasons explained in
'Documentation/process/submitting-patches.rst' and
'Documentation/process/5.Posting.rst'.

\
 
 \ /
  Last update: 2022-03-16 10:18    [W:0.231 / U:0.124 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site