lkml.org 
[lkml]   [2022]   [Feb]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 03/10] spi: spi-mem: Add driver for Aspeed SMC controllers
On 14/02/22 10:42AM, Cédric Le Goater wrote:
> This SPI driver adds support for the Aspeed static memory controllers
> of the AST2600, AST2500 and AST2400 SoCs using the spi-mem interface.
>
> * AST2600 Firmware SPI Memory Controller (FMC)
> . BMC firmware
> . 3 chip select pins (CE0 ~ CE2)
> . Only supports SPI type flash memory
> . different segment register interface
> . single, dual and quad mode.
>
> * AST2600 SPI Flash Controller (SPI1 and SPI2)
> . host firmware
> . 2 chip select pins (CE0 ~ CE1)
> . different segment register interface
> . single, dual and quad mode.
>
> * AST2500 Firmware SPI Memory Controller (FMC)
> . BMC firmware
> . 3 chip select pins (CE0 ~ CE2)
> . supports SPI type flash memory (CE0-CE1)
> . CE2 can be of NOR type flash but this is not supported by the driver
> . single, dual mode.
>
> * AST2500 SPI Flash Controller (SPI1 and SPI2)
> . host firmware
> . 2 chip select pins (CE0 ~ CE1)
> . single, dual mode.
>
> * AST2400 New Static Memory Controller (also referred as FMC)
> . BMC firmware
> . New register set
> . 5 chip select pins (CE0 ∼ CE4)
> . supports NOR flash, NAND flash and SPI flash memory.
> . single, dual and quad mode.
>
> Each controller has a memory range on which flash devices contents are
> mapped. Each device is assigned a window that can be changed at bootime
> with the Segment Address Registers.
>
> Each SPI flash device can then be accessed in two modes: Command and
> User. When in User mode, SPI transfers are initiated with accesses to
> the memory segment of a device. When in Command mode, memory
> operations on the memory segment of a device generate SPI commands
> automatically using a Control Register for the settings.
>
> This initial patch adds support for User mode. Command mode needs a little
> more work to check that the memory window on the AHB bus fits the device
> size. It will come later when support for direct mapping is added.
>
> Single and dual mode RX transfers are supported. Other types than SPI
> are not supported.
>
> Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
> Signed-off-by: Cédric Le Goater <clg@kaod.org>
> ---
> drivers/spi/spi-aspeed-smc.c | 766 ++++++++++++++++++++++++
> drivers/mtd/spi-nor/controllers/Kconfig | 2 +-
> drivers/spi/Kconfig | 11 +
> drivers/spi/Makefile | 1 +
> 4 files changed, 779 insertions(+), 1 deletion(-)
> create mode 100644 drivers/spi/spi-aspeed-smc.c
>
[...]
> +
> +/* support for 1-1-1, 1-1-2 or 1-1-4 */
> +static bool aspeed_spi_supports_op(struct spi_mem *mem, const struct spi_mem_op *op)
> +{
> + if (op->cmd.buswidth > 1)
> + return false;
> +
> + if (op->addr.nbytes != 0) {
> + if (op->addr.buswidth > 1 || op->addr.nbytes > 4)
> + return false;
> + }
> +
> + if (op->dummy.nbytes != 0) {
> + if (op->dummy.buswidth > 1 || op->dummy.nbytes > 7)
> + return false;
> + }
> +
> + if (op->data.nbytes != 0 && op->data.buswidth > 4)
> + return false;
> +
> + if (!spi_mem_default_supports_op(mem, op))
> + return false;
> +
> + return true;

Nitpick: You can just do return spi_mem_default_supports_op(mem, op);

> +}
> +
[...]
> +
> +static int aspeed_spi_init_devices(struct platform_device *pdev, struct aspeed_spi *aspi)
> +{
> + struct device_node *np;
> + unsigned int cs;
> + int ret;
> +
> + for_each_available_child_of_node(aspi->dev->of_node, np) {
> + struct aspeed_spi_chip *chip;
> +
> + if (!of_device_is_compatible(np, "jedec,spi-nor"))
> + continue;
> +
> + ret = of_property_read_u32(np, "reg", &cs);
> + if (ret) {
> + dev_err(aspi->dev, "Couldn't not read chip select.\n");
> + of_node_put(np);
> + return ret;
> + }
> +
> + if (cs > aspi->data->max_cs) {
> + dev_err(aspi->dev, "Chip select %d out of range.\n", cs);
> + of_node_put(np);
> + return -ERANGE;
> + }
> +
> + chip = &aspi->chips[cs];
> + chip->aspi = aspi;
> + chip->cs = cs;
> +
> + ret = aspeed_spi_chip_init(chip);
> + if (ret) {
> + of_node_put(np);
> + return ret;
> + }
> +
> + if (of_property_read_u32(np, "spi-max-frequency", &chip->clk_freq))
> + chip->clk_freq = ASPEED_SPI_DEFAULT_FREQ;
> +
> + aspi->num_cs++;
> + }

SPI MEM already gives you all this information. Get it from there, don't
parse it yourself.

You can get Chip Select via spi_mem->spi->chip_select.
You can get clock frequency via spi_mem->spi->max_speed_hz.

With these comments fixed,

Acked-by: Pratyush Yadav <p.yadav@ti.com>

> +
> + return 0;
> +}
> +
[...]

--
Regards,
Pratyush Yadav
Texas Instruments Inc.

\
 
 \ /
  Last update: 2022-02-25 08:51    [W:0.322 / U:0.568 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site