lkml.org 
[lkml]   [2022]   [Nov]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 5/7] riscv: dts: bouffalolab: add the bl808 SoC base device tree
On Sun, 20 Nov 2022 at 09:32, Jisheng Zhang <jszhang@kernel.org> wrote:
>
> Add a baisc dtsi for the bouffalolab bl808 SoC.
>
> Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
> ---
> arch/riscv/boot/dts/Makefile | 1 +
> arch/riscv/boot/dts/bouffalolab/bl808.dtsi | 74 ++++++++++++++++++++++
> 2 files changed, 75 insertions(+)
> create mode 100644 arch/riscv/boot/dts/bouffalolab/bl808.dtsi
>
> diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
> index ff174996cdfd..b525467152b2 100644
> --- a/arch/riscv/boot/dts/Makefile
> +++ b/arch/riscv/boot/dts/Makefile
> @@ -1,4 +1,5 @@
> # SPDX-License-Identifier: GPL-2.0
> +subdir-y += bouffalolab
> subdir-y += sifive
> subdir-y += starfive
> subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
> diff --git a/arch/riscv/boot/dts/bouffalolab/bl808.dtsi b/arch/riscv/boot/dts/bouffalolab/bl808.dtsi
> new file mode 100644
> index 000000000000..c98ebb14ee10
> --- /dev/null
> +++ b/arch/riscv/boot/dts/bouffalolab/bl808.dtsi
> @@ -0,0 +1,74 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2022 Jisheng Zhang <jszhang@kernel.org>
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + compatible = "bouffalolab,bl808";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + cpus {
> + timebase-frequency = <1000000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu0: cpu@0 {
> + compatible = "thead,c906", "riscv";
> + device_type = "cpu";
> + reg = <0>;
> + d-cache-block-size = <64>;
> + d-cache-sets = <256>;
> + d-cache-size = <32768>;
> + i-cache-block-size = <64>;
> + i-cache-sets = <128>;
> + i-cache-size = <32768>;
> + mmu-type = "riscv,sv39";
> + riscv,isa = "rv64imafdc";
> +
> + cpu0_intc: interrupt-controller {
> + compatible = "riscv,cpu-intc";
> + interrupt-controller;
> + #address-cells = <0>;
> + #interrupt-cells = <1>;
> + };
> + };
> + };
> +
> + xtal: xtal-clk {
> + compatible = "fixed-clock";
> + clock-frequency = <40000000>;

This was discussed many times before, but I think the conclusion was
that the frequency is a property of the crystal on the board, so this
should be 0 in the SoC dtsi, and then overwritten in the board device
tree.

> + clock-output-names = "xtal";
> + #clock-cells = <0>;
> + };
> +
> + soc {
> + compatible = "simple-bus";
> + ranges;
> + interrupt-parent = <&plic>;
> + dma-noncoherent;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + uart0: serial@30002000 {
> + compatible = "bouffalolab,uart";
> + reg = <0x30002000 0x1000>;
> + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&xtal>;
> + status = "disabled";
> + };
> +
> + plic: interrupt-controller@e0000000 {
> + compatible = "thead,c900-plic";
> + reg = <0xe0000000 0x4000000>;
> + interrupts-extended = <&cpu0_intc 0xffffffff>,
> + <&cpu0_intc 9>;
> + interrupt-controller;
> + #address-cells = <0>;
> + #interrupt-cells = <2>;
> + riscv,ndev = <64>;
> + };
> + };
> +};
> --
> 2.37.2
>
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv

\
 
 \ /
  Last update: 2022-11-20 15:59    [W:0.218 / U:0.372 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site