lkml.org 
[lkml]   [2022]   [Jan]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 1/2] arm: dts: sun7i: Add A20-Marsboard
Date
The Marsboard A20 is a A20 based SBC with 1G RAM, 8G Flash, micro SD
card slot , SATA socketm 10/100 ethernet, HDMI port, 4 USB2.0 ports, 2
USB2.0 OTG, USB WIFI(RTL8188EU) with antenna.

Signed-off-by: Conley Lee <conleylee@foxmail.com>
---
Change since v1.
- Spearate biddings and dts as two patches.
- use SPDX tag

Change since v2.
- reformat patch
- dual-license with GPL and MIT
- rename dts filename to sun7i-a20-haoyu-marsboard.dts
Change since v3.
- reformat patch
- order dtb alphabetically
- add gmac_txerr node and remove gmac_mii_pins node in
sun7i-a20-marsboard.dts
---
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/sun7i-a20-haoyu-marsboard.dts | 183 ++++++++++++++++++
2 files changed, 184 insertions(+)
create mode 100644 arch/arm/boot/dts/sun7i-a20-haoyu-marsboard.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0de64f237cd8..1850ff7c9006 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1213,6 +1213,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-bananapro.dtb \
sun7i-a20-cubieboard2.dtb \
sun7i-a20-cubietruck.dtb \
+ sun7i-a20-haoyu-marsboard.dtb \
sun7i-a20-hummingbird.dtb \
sun7i-a20-itead-ibox.dtb \
sun7i-a20-i12-tvbox.dtb \
diff --git a/arch/arm/boot/dts/sun7i-a20-haoyu-marsboard.dts b/arch/arm/boot/dts/sun7i-a20-haoyu-marsboard.dts
new file mode 100644
index 000000000000..056dbc415de7
--- /dev/null
+++ b/arch/arm/boot/dts/sun7i-a20-haoyu-marsboard.dts
@@ -0,0 +1,183 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2021 Conley Lee
+ * Conley Lee <conleylee@foxmail.com>
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "HAOYU Electronics Marsboard A20";
+ compatible = "haoyu,a20-marsboard", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+};
+
+&ahci {
+ target-supply = <&reg_ahci_5v>;
+ status = "okay";
+};
+
+&codec {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&reg_dcdc2>;
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_mii_pins>, <&gmac_txerr>;
+ phy-handle = <&phy0>;
+ phy-mode = "mii";
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <&reg_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
+ status = "okay";
+};
+
+&gmac_mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ gmac_txerr: gmac-txerr-pin {
+ pins = "PA17";
+ function = "gmac";
+ };
+};
+
+
+&reg_ahci_5v {
+ status = "okay";
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+ status = "okay";
+};
+
+&reg_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+&reg_usb1_vbus {
+ status = "okay";
+};
+
+&reg_usb2_vbus {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+ usb1_vbus-supply = <&reg_usb1_vbus>;
+ usb2_vbus-supply = <&reg_usb2_vbus>;
+ status = "okay";
+};
--
2.31.1
\
 
 \ /
  Last update: 2022-01-14 17:34    [W:0.251 / U:0.188 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site