lkml.org 
[lkml]   [2021]   [Sep]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v3 5/8] dt-bindings: mtd: ti,gpmc-nand: Convert to yaml
On Wed, Sep 8, 2021 at 6:14 AM Roger Quadros <rogerq@kernel.org> wrote:
>
>
>
> On 07/09/2021 20:01, Rob Herring wrote:
> > On Tue, Sep 07, 2021 at 02:32:23PM +0300, Roger Quadros wrote:
> >> Convert gpmc-nand.txt to ti,gpmc-nand.yaml.
> >>
> >> Signed-off-by: Roger Quadros <rogerq@kernel.org>
> >> ---
> >> .../devicetree/bindings/mtd/gpmc-nand.txt | 147 ------------------
> >> .../devicetree/bindings/mtd/ti,gpmc-nand.yaml | 110 +++++++++++++
> >> 2 files changed, 110 insertions(+), 147 deletions(-)
> >> delete mode 100644 Documentation/devicetree/bindings/mtd/gpmc-nand.txt
> >> create mode 100644 Documentation/devicetree/bindings/mtd/ti,gpmc-nand.yaml
> >>
> >> diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
> >> deleted file mode 100644
> >> index 44919d48d241..000000000000
> >> --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
> >> +++ /dev/null
> >> @@ -1,147 +0,0 @@
> >> -Device tree bindings for GPMC connected NANDs
> >> -
> >> -GPMC connected NAND (found on OMAP boards) are represented as child nodes of
> >> -the GPMC controller with a name of "nand".
> >> -
> >> -All timing relevant properties as well as generic gpmc child properties are
> >> -explained in a separate documents - please refer to
> >> -Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
> >> -
> >> -For NAND specific properties such as ECC modes or bus width, please refer to
> >> -Documentation/devicetree/bindings/mtd/nand-controller.yaml
> >> -
> >> -
> >> -Required properties:
> >> -
> >> - - compatible: "ti,omap2-nand"
> >> - - reg: range id (CS number), base offset and length of the
> >> - NAND I/O space
> >> - - interrupts: Two interrupt specifiers, one for fifoevent, one for termcount.
> >> -
> >> -Optional properties:
> >> -
> >> - - nand-bus-width: Set this numeric value to 16 if the hardware
> >> - is wired that way. If not specified, a bus
> >> - width of 8 is assumed.
> >> -
> >> - - ti,nand-ecc-opt: A string setting the ECC layout to use. One of:
> >> - "sw" 1-bit Hamming ecc code via software
> >> - "hw" <deprecated> use "ham1" instead
> >> - "hw-romcode" <deprecated> use "ham1" instead
> >> - "ham1" 1-bit Hamming ecc code
> >> - "bch4" 4-bit BCH ecc code
> >> - "bch8" 8-bit BCH ecc code
> >> - "bch16" 16-bit BCH ECC code
> >> - Refer below "How to select correct ECC scheme for your device ?"
> >> -
> >> - - ti,nand-xfer-type: A string setting the data transfer type. One of:
> >> -
> >> - "prefetch-polled" Prefetch polled mode (default)
> >> - "polled" Polled mode, without prefetch
> >> - "prefetch-dma" Prefetch enabled DMA mode
> >> - "prefetch-irq" Prefetch enabled irq mode
> >> -
> >> - - elm_id: <deprecated> use "ti,elm-id" instead
> >> - - ti,elm-id: Specifies phandle of the ELM devicetree node.
> >> - ELM is an on-chip hardware engine on TI SoC which is used for
> >> - locating ECC errors for BCHx algorithms. SoC devices which have
> >> - ELM hardware engines should specify this device node in .dtsi
> >> - Using ELM for ECC error correction frees some CPU cycles.
> >> - - rb-gpios: GPIO specifier for the ready/busy# pin.
> >> -
> >> -For inline partition table parsing (optional):
> >> -
> >> - - #address-cells: should be set to 1
> >> - - #size-cells: should be set to 1
> >> -
> >> -Example for an AM33xx board:
> >> -
> >> - gpmc: gpmc@50000000 {
> >> - compatible = "ti,am3352-gpmc";
> >> - ti,hwmods = "gpmc";
> >> - reg = <0x50000000 0x36c>;
> >> - interrupts = <100>;
> >> - gpmc,num-cs = <8>;
> >> - gpmc,num-waitpins = <2>;
> >> - #address-cells = <2>;
> >> - #size-cells = <1>;
> >> - ranges = <0 0 0x08000000 0x1000000>; /* CS0 space, 16MB */
> >> - elm_id = <&elm>;
> >> - interrupt-controller;
> >> - #interrupt-cells = <2>;
> >> -
> >> - nand@0,0 {
> >> - compatible = "ti,omap2-nand";
> >> - reg = <0 0 4>; /* CS0, offset 0, NAND I/O window 4 */
> >> - interrupt-parent = <&gpmc>;
> >> - interrupts = <0 IRQ_TYPE_NONE>, <1 IRQ_TYPE NONE>;
> >> - nand-bus-width = <16>;
> >> - ti,nand-ecc-opt = "bch8";
> >> - ti,nand-xfer-type = "polled";
> >> - rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
> >> -
> >> - gpmc,sync-clk-ps = <0>;
> >> - gpmc,cs-on-ns = <0>;
> >> - gpmc,cs-rd-off-ns = <44>;
> >> - gpmc,cs-wr-off-ns = <44>;
> >> - gpmc,adv-on-ns = <6>;
> >> - gpmc,adv-rd-off-ns = <34>;
> >> - gpmc,adv-wr-off-ns = <44>;
> >> - gpmc,we-off-ns = <40>;
> >> - gpmc,oe-off-ns = <54>;
> >> - gpmc,access-ns = <64>;
> >> - gpmc,rd-cycle-ns = <82>;
> >> - gpmc,wr-cycle-ns = <82>;
> >> - gpmc,wr-access-ns = <40>;
> >> - gpmc,wr-data-mux-bus-ns = <0>;
> >> -
> >> - #address-cells = <1>;
> >> - #size-cells = <1>;
> >> -
> >> - /* partitions go here */
> >> - };
> >> - };
> >> -
> >> -How to select correct ECC scheme for your device ?
> >> ---------------------------------------------------
> >> -Higher ECC scheme usually means better protection against bit-flips and
> >> -increased system lifetime. However, selection of ECC scheme is dependent
> >> -on various other factors also like;
> >> -
> >> -(1) support of built in hardware engines.
> >> - Some legacy OMAP SoC do not have ELM harware engine, so those SoC cannot
> >> - support ecc-schemes with hardware error-correction (BCHx_HW). However
> >> - such SoC can use ecc-schemes with software library for error-correction
> >> - (BCHx_HW_DETECTION_SW). The error correction capability with software
> >> - library remains equivalent to their hardware counter-part, but there is
> >> - slight CPU penalty when too many bit-flips are detected during reads.
> >> -
> >> -(2) Device parameters like OOBSIZE.
> >> - Other factor which governs the selection of ecc-scheme is oob-size.
> >> - Higher ECC schemes require more OOB/Spare area to store ECC syndrome,
> >> - so the device should have enough free bytes available its OOB/Spare
> >> - area to accommodate ECC for entire page. In general following expression
> >> - helps in determining if given device can accommodate ECC syndrome:
> >> - "2 + (PAGESIZE / 512) * ECC_BYTES" >= OOBSIZE"
> >> - where
> >> - OOBSIZE number of bytes in OOB/spare area
> >> - PAGESIZE number of bytes in main-area of device page
> >> - ECC_BYTES number of ECC bytes generated to protect
> >> - 512 bytes of data, which is:
> >> - '3' for HAM1_xx ecc schemes
> >> - '7' for BCH4_xx ecc schemes
> >> - '14' for BCH8_xx ecc schemes
> >> - '26' for BCH16_xx ecc schemes
> >> -
> >> - Example(a): For a device with PAGESIZE = 2048 and OOBSIZE = 64 and
> >> - trying to use BCH16 (ECC_BYTES=26) ecc-scheme.
> >> - Number of ECC bytes per page = (2 + (2048 / 512) * 26) = 106 B
> >> - which is greater than capacity of NAND device (OOBSIZE=64)
> >> - Hence, BCH16 cannot be supported on given device. But it can
> >> - probably use lower ecc-schemes like BCH8.
> >> -
> >> - Example(b): For a device with PAGESIZE = 2048 and OOBSIZE = 128 and
> >> - trying to use BCH16 (ECC_BYTES=26) ecc-scheme.
> >> - Number of ECC bytes per page = (2 + (2048 / 512) * 26) = 106 B
> >> - which can be accommodated in the OOB/Spare area of this device
> >> - (OOBSIZE=128). So this device can use BCH16 ecc-scheme.
> >> diff --git a/Documentation/devicetree/bindings/mtd/ti,gpmc-nand.yaml b/Documentation/devicetree/bindings/mtd/ti,gpmc-nand.yaml
> >> new file mode 100644
> >> index 000000000000..db36f2e944ef
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/mtd/ti,gpmc-nand.yaml
> >> @@ -0,0 +1,110 @@
> >> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> >> +%YAML 1.2
> >> +---
> >> +$id: http://devicetree.org/schemas/mtd/ti,gpmc-nand.yaml#
> >> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> >> +
> >> +title: Texas Instruments GPMC NAND Flash controller.
> >> +
> >> +maintainers:
> >> + - Tony Lindgren <tony@atomide.com>
> >> + - Roger Quadros <rogerq@kernel.org>
> >> +
> >> +description:
> >> + GPMC NAND controller/Flash is represented as a child of the
> >> + GPMC controller node.
> >> +
> >> +properties:
> >> + compatible:
> >> + const: ti,omap2-nand
> >> +
> >> + reg:
> >> + maxItems: 1
> >> +
> >> + interrupts:
> >> + items:
> >> + - description: Interrupt for fifoevent
> >> + - description: Interrupt for termcount
> >> +
> >> + "#address-cells":
> >> + const: 1
> >> +
> >> + "#size-cells":
> >> + const: 1
> >> +
> >> + ti,nand-ecc-opt:
> >> + description: Desired ECC algorithm
> >> + $ref: /schemas/types.yaml#/definitions/string
> >> + enum: [sw, ham1, bch4, bch8, bch16]
> >> +
> >> + ti,nand-xfer-type:
> >> + description: Data transfer method between controller and chip.
> >> + $ref: /schemas/types.yaml#/definitions/string
> >> + enum: [prefetch-polled, polled, prefetch-dma, prefetch-irq]
> >> + default: prefetch-polled
> >> +
> >> + ti,elm-id:
> >> + description:
> >> + phandle to the ELM (Error Location Module).
> >> + $ref: /schemas/types.yaml#/definitions/phandle
> >> +
> >> + nand-bus-width:
> >> + description:
> >> + Bus width to the NAND chip
> >> + $ref: /schemas/types.yaml#/definitions/uint32
> >> + enum: [8, 16]
> >> + default: 8
> >> +
> >> +allOf:
> >> + - $ref: "../memory-controllers/ti,gpmc-child.yaml"
> >
> > Use /schemas/... rather than '..'
>
> ok.
>
> >
> >> +
> >> +required:
> >> + - compatible
> >> + - reg
> >> + - ti,nand-ecc-opt
> >> +
> >> +unevaluatedProperties: false
> >
> > This will throw errors if you have partition nodes. You need to
> > reference the partitions schema.
>
> I didn't get any errors with dtbs_check so far. But I will
> try referencing the partition schema here.

Not yet because 'unevaluatedProperties' isn't actually supported in
the jsonschema package yet. It will be in the next release which I
expect soonish.

Rob

\
 
 \ /
  Last update: 2021-09-08 14:47    [W:0.079 / U:0.240 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site