lkml.org 
[lkml]   [2021]   [Sep]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 3/3] ARM: at91: pm: preload base address of controllers in tlb
Date
In suspend/resume procedure for AT91 architecture different controllers
(PMC, SHDWC, RAM, RAM PHY, SFRBU) are accessed to do the proper settings
for power saving. Commit f0bbf17958e8 ("ARM: at91: pm: add self-refresh
support for sama7g5") introduced the access to RAMC PHY controller for
SAMA7G5. The access to this controller is done after RAMC ports are
closed, thus any TLB walk necessary for RAMC PHY virtual address will
fail. In the development branch this was not encountered. However, on
current kernel the issue is reproducible.

To solve the issue the previous mechanism of pre-loading the TLB with
the RAMC PHY virtual address has been used. However, only the addition
of this new pre-load breaks the functionality for ARMv5 based
devices (SAM9X60). This behavior has been encountered previously
while debugging this code and using the same mechanism for pre-loading
address for different controllers (e.g. pin controller, the assumption
being that other requested translations are replaced from TLB).

To solve this new issue the TLB flush + the extension of pre-loading
the rest of controllers to TLB (e.g. PMC, RAMC) has been added. The
rest of the controllers should have been pre-loaded previously, anyway.

Fixes: f0bbf17958e8 ("ARM: at91: pm: add self-refresh support for sama7g5")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
---

Hi Nicolas,

Please link this patch with the previous one in this series ("ARM: at91:
pm: group constants and addresses loading") with a Depends-on tag as this
will fail to apply if backported to older kernel versions.

Thank you,
Claudiu Beznea

arch/arm/mach-at91/pm_suspend.S | 25 ++++++++++++++++++++++++-
1 file changed, 24 insertions(+), 1 deletion(-)

diff --git a/arch/arm/mach-at91/pm_suspend.S b/arch/arm/mach-at91/pm_suspend.S
index 34f251fdb743..fdb4f63ecde4 100644
--- a/arch/arm/mach-at91/pm_suspend.S
+++ b/arch/arm/mach-at91/pm_suspend.S
@@ -1014,6 +1014,10 @@ ENTRY(at91_pm_suspend_in_sram)
mov tmp1, #0
mcr p15, 0, tmp1, c7, c10, 4

+ /* Flush tlb. */
+ mov r4, #0
+ mcr p15, 0, r4, c8, c7, 0
+
ldr tmp1, [r0, #PM_DATA_PMC_MCKR_OFFSET]
str tmp1, .mckr_offset
ldr tmp1, [r0, #PM_DATA_PMC_VERSION]
@@ -1023,23 +1027,42 @@ ENTRY(at91_pm_suspend_in_sram)
ldr tmp1, [r0, #PM_DATA_MODE]
str tmp1, .pm_mode

+ /*
+ * ldrne below are here to preload their address in the TLB as access
+ * to RAM may be limited while in self-refresh.
+ */
ldr tmp1, [r0, #PM_DATA_PMC]
str tmp1, .pmc_base
+ cmp tmp1, #0
+ ldrne tmp2, [tmp1, #0]
+
ldr tmp1, [r0, #PM_DATA_RAMC0]
str tmp1, .sramc_base
+ cmp tmp1, #0
+ ldrne tmp2, [tmp1, #0]
+
ldr tmp1, [r0, #PM_DATA_RAMC1]
str tmp1, .sramc1_base
+ cmp tmp1, #0
+ ldrne tmp2, [tmp1, #0]
+
+#ifndef CONFIG_SOC_SAM_V4_V5
+ /* ldrne below are here to preload their address in the TLB */
ldr tmp1, [r0, #PM_DATA_RAMC_PHY]
str tmp1, .sramc_phy_base
- /* Both ldrne below are here to preload their address in the TLB */
+ cmp tmp1, #0
+ ldrne tmp2, [tmp1, #0]
+
ldr tmp1, [r0, #PM_DATA_SHDWC]
str tmp1, .shdwc
cmp tmp1, #0
ldrne tmp2, [tmp1, #0]
+
ldr tmp1, [r0, #PM_DATA_SFRBU]
str tmp1, .sfrbu
cmp tmp1, #0
ldrne tmp2, [tmp1, #0x10]
+#endif

/* Active the self-refresh mode */
at91_sramc_self_refresh_ena
--
2.25.1
\
 
 \ /
  Last update: 2021-09-30 17:43    [W:0.054 / U:0.420 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site