lkml.org 
[lkml]   [2021]   [Sep]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 1/2] dt-bindings: mtd: spi-nand: Convert to DT schema format
Hello Rob, Mark,

robh@kernel.org wrote on Tue, 21 Sep 2021 14:16:02 -0500:

> On Tue, Sep 21, 2021 at 8:43 AM Apurva Nandan <a-nandan@ti.com> wrote:
> >
> > Hi Rob,
> >
> > On 21/09/21 2:46 am, Rob Herring wrote:
> > > On Mon, Sep 20, 2021 at 06:06:51PM +0300, Serge Semin wrote:
> > >> Hello Apurva
> > >>
> > >> On Mon, Sep 20, 2021 at 07:57:12PM +0530, Apurva Nandan wrote:
> > >>> Convert spi-nand.txt binding to YAML format with an added example.
> > >>>
> > >>> Signed-off-by: Apurva Nandan <a-nandan@ti.com>
> > >>> ---
> > >>> .../devicetree/bindings/mtd/spi-nand.txt | 5 --
> > >>> .../devicetree/bindings/mtd/spi-nand.yaml | 62 +++++++++++++++++++
> > >>> 2 files changed, 62 insertions(+), 5 deletions(-)
> > >>> delete mode 100644 Documentation/devicetree/bindings/mtd/spi-nand.txt
> > >>> create mode 100644 Documentation/devicetree/bindings/mtd/spi-nand.yaml
> > >> Thanks for the bindings conversion patch. There are several comments
> > >> below. But before addressing them it would be better to also get a
> > >> response from Rob.
> > >>
> > >>> diff --git a/Documentation/devicetree/bindings/mtd/spi-nand.txt b/Documentation/devicetree/bindings/mtd/spi-nand.txt
> > >>> deleted file mode 100644
> > >>> index 8b51f3b6d55c..000000000000
> > >>> --- a/Documentation/devicetree/bindings/mtd/spi-nand.txt
> > >>> +++ /dev/null
> > >>> @@ -1,5 +0,0 @@
> > >>> -SPI NAND flash
> > >>> -
> > >>> -Required properties:
> > >>> -- compatible: should be "spi-nand"
> > >>> -- reg: should encode the chip-select line used to access the NAND chip
> > >>> diff --git a/Documentation/devicetree/bindings/mtd/spi-nand.yaml b/Documentation/devicetree/bindings/mtd/spi-nand.yaml
> > >>> new file mode 100644
> > >>> index 000000000000..601beba8d971
> > >>> --- /dev/null
> > >>> +++ b/Documentation/devicetree/bindings/mtd/spi-nand.yaml
> > >>> @@ -0,0 +1,62 @@
> > >>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > >>> +%YAML 1.2
> > >>> +---
> > >>> +$id: http://devicetree.org/schemas/mtd/spi-nand.yaml#
> > >>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > >>> +
> > >>> +title: SPI NAND flash
> > >>> +
> > >>> +maintainers:
> > >>> + - Apurva Nandan <a-nandan@ti.com>
> > >>> +
> > >>> +allOf:
> > >>> + - $ref: "mtd.yaml#"
> > >>> +
> > >>> +properties:
> > >>> + compatible:
> > >>> + const: spi-nand
> > >>> +
> > >>> + reg:
> > >>> + maxItems: 1
> > >>> +
> > >>> + spi-max-frequency: true
> > >>> + spi-rx-bus-width: true
> > >>> + spi-tx-bus-width: true
> > >>> + rx-sample-delay-ns: true
> > >> Since it's an SPI-client device there are more than these properties
> > >> could be set for it. See the SPI-controller bindings schema:
> > >> Documentation/devicetree/bindings/spi/spi-controller.yaml
> > >> So there is two possible ways to make it more generic:
> > >> 1) Detach the spi-client part from the spi-controller.yaml bindings
> > >> into a dedicated DT-schema file and refer to that new scheme from
> > >> here.
> > > Yes, as mentioned there's patches doing this. But the above is fine.
> > > There's some value in defining here which properties are valid.
> > Yeah right
> > >> 2) Forget about these controller-specific properties and let the
> > >> parental SPI-controller bindings parsing them. Of course there must be
> > >> at least one of the next properties declared for it to work:
> > >> {unevaluatedProperties, additionalProperties}.
> > >>
> > >> It's up to Rob to decided which approach is better though...
> > >>
> > >>> +
> > >>> + '#address-cells': true
> > >>> + '#size-cells': true
> > >> Aren't they always equal to 1?
> > > No SPI nand devices >4GB?
> > Yeah, we have SPI NANDs >4GB, and "'#address-cells': true" allows those
> > sizes.
> > >
> > >>> +
> > >>> +additionalProperties:
> > >>> + type: object
> > >> I'd suggest to elaborate the way the partition sub-nodes looks
> > >> like, for instance, the node names, supported compatible names,
> > >> labels, etc.
> > > That should probably all be in mtd.yaml. The question here is whether
> > > partitions are always under a 'partitions' node. Maybe this is new
> > > enough that only the new way has to be supported. Though if mtd.yaml
> > > supported both forms, allowing both all the time is okay IMO.
> > >
> > > Rob
> >
> > I had added the "partition" node properties in the v1 patch, but as per
> > the reviews I removed it.
> > I think we can prefer having them in mtd.yaml if needed, in a separate
> > patch series.
> > Do you prefer the mtd.yaml changes as a part of this series or as a
> > separate patch?
> >
> > Other than that, I don't find any need for a v3 patch re-roll, do you agree?
>
> Yeah, I suppose not.
>
> Reviewed-by: Rob Herring <robh@kernel.org>
>
> And actually, it's Miquel that should apply these 2 rather than Mark.

Yeah, but that's fine for this one, I don't expect conflicts anyway.

Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>

Thanks,
Miquèl

\
 
 \ /
  Last update: 2021-09-22 10:32    [W:0.260 / U:0.780 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site