lkml.org 
[lkml]   [2021]   [Sep]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] drivers: mfd: da9063: Add restart notifier implementation
On Tue, Sep 21, 2021 at 12:25 PM Ben Dooks <ben.dooks@codethink.co.uk> wrote:
>
> On 21/09/2021 06:33, Alexandre Ghiti wrote:
> > The SiFive Unmatched board uses the da9063 PMIC for reset: add a restart
> > notifier that will execute a small i2c sequence allowing to reset the
> > board.
> >
> > The original implementation comes from Marcus Comstedt and Anders Montonen
> > (https://forums.sifive.com/t/reboot-command/4721/28).
> >
> > Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
>
> I've got a couple of comments here, mainly is this the right place
> and has anyone other than you tested. I tried something similar on
> my Unmatched and it just turned the board off.

Someone else in the thread I mention in the commit log tried it, but
more feedback are welcome :)

For the Unmatched, this solution will be temporary, the best place
being openSBI which lacks i2c support for now.
But I think this can be used by other boards using this PMIC.

>
> > ---
> > drivers/mfd/da9063-core.c | 25 +++++++++++++++++++++++++
> > include/linux/mfd/da9063/core.h | 3 +++
> > 2 files changed, 28 insertions(+)
> >
> > diff --git a/drivers/mfd/da9063-core.c b/drivers/mfd/da9063-core.c
> > index df407c3afce3..c87b8d611f20 100644
> > --- a/drivers/mfd/da9063-core.c
> > +++ b/drivers/mfd/da9063-core.c
> > @@ -20,6 +20,7 @@
> > #include <linux/mutex.h>
> > #include <linux/mfd/core.h>
> > #include <linux/regmap.h>
> > +#include <linux/reboot.h>
> >
> > #include <linux/mfd/da9063/core.h>
> > #include <linux/mfd/da9063/registers.h>
> > @@ -158,6 +159,18 @@ static int da9063_clear_fault_log(struct da9063 *da9063)
> > return ret;
> > }
> >
> > +static int da9063_restart_notify(struct notifier_block *this,
> > + unsigned long mode, void *cmd)
> > +{
> > + struct da9063 *da9063 = container_of(this, struct da9063, restart_handler);
> > +
> > + regmap_write(da9063->regmap, DA9063_REG_PAGE_CON, 0x00);
> > + regmap_write(da9063->regmap, DA9063_REG_CONTROL_F, 0x04);
> > + regmap_write(da9063->regmap, DA9063_REG_CONTROL_A, 0x68);
> > +
> > + return NOTIFY_DONE;
> > +}
> > +
>
> Firstly, do you also need to force the AUTOBOOT (bit 3, CONTROL_C)
> to ensure the PMIC does restart.

I tried this too and actually, it seems that the value is read from
OTP at reboot and as it is not set here, it has no effect.

>
> > int da9063_device_init(struct da9063 *da9063, unsigned int irq)
> > {
> > int ret;
> > @@ -197,6 +210,18 @@ int da9063_device_init(struct da9063 *da9063, unsigned int irq)
> > }
> > }
> >
> > + da9063->restart_handler.notifier_call = da9063_restart_notify;
> > + da9063->restart_handler.priority = 128;
> > + ret = register_restart_handler(&da9063->restart_handler);
> > + if (ret) {
> > + dev_err(da9063->dev, "Failed to register restart handler\n");
> > + return ret;
> > + }
> > +
> > + devm_add_action(da9063->dev,
> > + (void (*)(void *))unregister_restart_handler,
> > + &da9063->restart_handler);
>
> there's devm_register_reboot_notifier()

Thanks for that!

>
>
> > +
> > return ret;
> > }
> >
> > diff --git a/include/linux/mfd/da9063/core.h b/include/linux/mfd/da9063/core.h
> > index fa7a43f02f27..1b20c498e340 100644
> > --- a/include/linux/mfd/da9063/core.h
> > +++ b/include/linux/mfd/da9063/core.h
> > @@ -85,6 +85,9 @@ struct da9063 {
> > int chip_irq;
> > unsigned int irq_base;
> > struct regmap_irq_chip_data *regmap_irq;
> > +
> > + /* Restart */
> > + struct notifier_block restart_handler;
> > };
> >
> > int da9063_device_init(struct da9063 *da9063, unsigned int irq);
>
> Note, the watchdog driver for the DA9063 also has a restart method
> although it also does not set the AUTOBOOT bit either.
>
> The best thing is to enable the watchdog driver, the SiFive release
> does not have either the core DA9063 or the watchdog driver for it
> enabled.

It seems that for the restart implemented here to work, the AUTOBOOT
bit needs to be set in the OTP, which seems not to be the case with
the chip on this board: it's been discussed here
https://www.dialog-semiconductor.com/products/pmics?post_id=10052#tab-support_tab_content
(see the accepted answer).

Thanks,

Alex

>
> --
> Ben Dooks http://www.codethink.co.uk/
> Senior Engineer Codethink - Providing Genius
>
> https://www.codethink.co.uk/privacy.html

\
 
 \ /
  Last update: 2021-09-21 13:33    [W:0.084 / U:2.104 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site