lkml.org 
[lkml]   [2021]   [Sep]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/2] ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins
Date
With commit c709135e576b ("pinctrl: at91-pio4: add support for slew-rate")
and commit cbde6c823bfa ("pinctrl: at91-pio4: Fix slew rate disablement")
the slew-rate is enabled by default for each configured pin. The datasheet
specifies at chapter "Output Driver AC Characteristics" that HSIO
drivers (use in SDMMCx and QSPI0 peripherals), don't have a slewrate
setting but are rather calibrated against an external 1% resistor mounted
on the SDMMCx_CAL or QSPI0_CAL pins. Depending on the target signal
frequency and the external load, it is possible to adjust their target
output impedance. Thus set slew-rate = <0> for SDMMC (QSPI is not enabled
at the moment in device tree).

Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
---
arch/arm/boot/dts/at91-sama7g5ek.dts | 6 ++++++
1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/at91-sama7g5ek.dts b/arch/arm/boot/dts/at91-sama7g5ek.dts
index 0bed8207d498..624162fec223 100644
--- a/arch/arm/boot/dts/at91-sama7g5ek.dts
+++ b/arch/arm/boot/dts/at91-sama7g5ek.dts
@@ -556,6 +556,7 @@ cmd_data {
<PIN_PA8__SDMMC0_DAT5>,
<PIN_PA9__SDMMC0_DAT6>,
<PIN_PA10__SDMMC0_DAT7>;
+ slew-rate = <0>;
bias-pull-up;
};

@@ -563,6 +564,7 @@ ck_cd_rstn_vddsel {
pinmux = <PIN_PA0__SDMMC0_CK>,
<PIN_PA2__SDMMC0_RSTN>,
<PIN_PA11__SDMMC0_DS>;
+ slew-rate = <0>;
bias-pull-up;
};
};
@@ -574,6 +576,7 @@ cmd_data {
<PIN_PC0__SDMMC1_DAT1>,
<PIN_PC1__SDMMC1_DAT2>,
<PIN_PC2__SDMMC1_DAT3>;
+ slew-rate = <0>;
bias-pull-up;
};

@@ -582,6 +585,7 @@ ck_cd_rstn_vddsel {
<PIN_PB28__SDMMC1_RSTN>,
<PIN_PC5__SDMMC1_1V8SEL>,
<PIN_PC4__SDMMC1_CD>;
+ slew-rate = <0>;
bias-pull-up;
};
};
@@ -593,11 +597,13 @@ cmd_data {
<PIN_PD6__SDMMC2_DAT1>,
<PIN_PD7__SDMMC2_DAT2>,
<PIN_PD8__SDMMC2_DAT3>;
+ slew-rate = <0>;
bias-pull-up;
};

ck {
pinmux = <PIN_PD4__SDMMC2_CK>;
+ slew-rate = <0>;
bias-pull-up;
};
};
--
2.25.1
\
 
 \ /
  Last update: 2021-09-15 09:51    [W:1.837 / U:0.392 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site