lkml.org 
[lkml]   [2021]   [Aug]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [Freedreno] [PATCH 10/11] drm/msm/dsi: Add support for DSC configuration
On 2021-07-14 23:52, Vinod Koul wrote:
> When DSC is enabled, we need to configure DSI registers accordingly and
> configure the respective stream compression registers.
>
> Add support to calculate the register setting based on DSC params and
> timing information and configure these registers.
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>

same comments as dmitry on this one:
https://patchwork.freedesktop.org/patch/444082/?series=90413&rev=2
nothing more to add.

> ---
> drivers/gpu/drm/msm/dsi/dsi.xml.h | 10 ++
> drivers/gpu/drm/msm/dsi/dsi_host.c | 142 +++++++++++++++++++++++++++--
> 2 files changed, 142 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/gpu/drm/msm/dsi/dsi.xml.h
> b/drivers/gpu/drm/msm/dsi/dsi.xml.h
> index 50eb4d1b8fdd..b8e9e608abfc 100644
> --- a/drivers/gpu/drm/msm/dsi/dsi.xml.h
> +++ b/drivers/gpu/drm/msm/dsi/dsi.xml.h
> @@ -2310,4 +2310,14 @@ static inline uint32_t
> REG_DSI_7nm_PHY_LN_TX_DCTRL(uint32_t i0) { return 0x00000
>
> #define REG_DSI_7nm_PHY_PLL_PERF_OPTIMIZE 0x00000260
>
> +#define REG_DSI_VIDEO_COMPRESSION_MODE_CTRL 0x0000029c
> +
> +#define REG_DSI_VIDEO_COMPRESSION_MODE_CTRL2 0x000002a0
> +
> +#define REG_DSI_COMMAND_COMPRESSION_MODE_CTRL 0x000002a4
> +
> +#define REG_DSI_COMMAND_COMPRESSION_MODE_CTRL2 0x000002a8
> +
> +#define REG_DSI_COMMAND_COMPRESSION_MODE_CTRL3 0x000002ac
> +
> #endif /* DSI_XML */
> diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c
> b/drivers/gpu/drm/msm/dsi/dsi_host.c
> index e1e5d91809b5..4e8ab1b1df8b 100644
> --- a/drivers/gpu/drm/msm/dsi/dsi_host.c
> +++ b/drivers/gpu/drm/msm/dsi/dsi_host.c
> @@ -942,6 +942,26 @@ static void dsi_ctrl_config(struct msm_dsi_host
> *msm_host, bool enable,
> dsi_write(msm_host, REG_DSI_CTRL, data);
> }
>
> +static int dsi_dsc_update_pic_dim(struct msm_display_dsc_config *dsc,
> + int pic_width, int pic_height)
> +{
> + if (!dsc || !pic_width || !pic_height) {
> + pr_err("DSI: invalid input: pic_width: %d pic_height: %d\n",
> pic_width, pic_height);
> + return -EINVAL;
> + }
> +
> + if ((pic_width % dsc->drm->slice_width) || (pic_height %
> dsc->drm->slice_height)) {
> + pr_err("DSI: pic_dim %dx%d has to be multiple of slice %dx%d\n",
> + pic_width, pic_height, dsc->drm->slice_width,
> dsc->drm->slice_height);
> + return -EINVAL;
> + }
> +
> + dsc->drm->pic_width = pic_width;
> + dsc->drm->pic_height = pic_height;
> +
> + return 0;
> +}
> +
> static void dsi_timing_setup(struct msm_dsi_host *msm_host, bool
> is_dual_dsi)
> {
> struct drm_display_mode *mode = msm_host->mode;
> @@ -956,6 +976,7 @@ static void dsi_timing_setup(struct msm_dsi_host
> *msm_host, bool is_dual_dsi)
> u32 va_end = va_start + mode->vdisplay;
> u32 hdisplay = mode->hdisplay;
> u32 wc;
> + u32 data;
>
> DBG("");
>
> @@ -974,7 +995,73 @@ static void dsi_timing_setup(struct msm_dsi_host
> *msm_host, bool is_dual_dsi)
> hdisplay /= 2;
> }
>
> + if (msm_host->dsc) {
> + struct msm_display_dsc_config *dsc = msm_host->dsc;
> +
> + /* update dsc params with timing params */
> + dsi_dsc_update_pic_dim(dsc, mode->hdisplay, mode->vdisplay);
> + DBG("Mode Width- %d x Height %d\n", dsc->drm->pic_width,
> dsc->drm->pic_height);
> +
> + /* we do the calculations for dsc parameters here so that
> + * panel can use these parameters
> + */
> + dsi_populate_dsc_params(dsc);
> +
> + /* Divide the display by 3 but keep back/font porch and
> + * pulse width same
> + */
> + h_total -= hdisplay;
> + hdisplay /= 3;
> + h_total += hdisplay;
> + ha_end = ha_start + hdisplay;
> + }
> +
> if (msm_host->mode_flags & MIPI_DSI_MODE_VIDEO) {
> + if (msm_host->dsc) {
> + struct msm_display_dsc_config *dsc = msm_host->dsc;
> + u32 reg, intf_width, slice_per_intf, width;
> + u32 total_bytes_per_intf;
> +
> + /* first calculate dsc parameters and then program
> + * compress mode registers
> + */
> + intf_width = hdisplay;
> + slice_per_intf = DIV_ROUND_UP(intf_width, dsc->drm->slice_width);
> +
> + /* If slice_count > slice_per_intf, then use 1
> + * This can happen during partial update
> + */
> + dsc->drm->slice_count = 1;
> +
> + dsc->bytes_in_slice = DIV_ROUND_UP(dsc->drm->slice_width * 8, 8);
> + total_bytes_per_intf = dsc->bytes_in_slice * slice_per_intf;
> +
> + dsc->eol_byte_num = total_bytes_per_intf % 3;
> + dsc->pclk_per_line = DIV_ROUND_UP(total_bytes_per_intf, 3);
> + dsc->bytes_per_pkt = dsc->bytes_in_slice * dsc->drm->slice_count;
> + dsc->pkt_per_line = slice_per_intf / dsc->drm->slice_count;
> +
> + width = dsc->pclk_per_line;
> + reg = dsc->bytes_per_pkt << 16;
> + reg |= (0x0b << 8); /* dtype of compressed image */
> +
> + /* pkt_per_line:
> + * 0 == 1 pkt
> + * 1 == 2 pkt
> + * 2 == 4 pkt
> + * 3 pkt is not supported
> + * above translates to ffs() - 1
> + */
> + reg |= (ffs(dsc->pkt_per_line) - 1) << 6;
> +
> + dsc->eol_byte_num = total_bytes_per_intf % 3;
> + reg |= dsc->eol_byte_num << 4;
> + reg |= 1;
> +
> + dsi_write(msm_host,
> + REG_DSI_VIDEO_COMPRESSION_MODE_CTRL, reg);
> + }
> +
> dsi_write(msm_host, REG_DSI_ACTIVE_H,
> DSI_ACTIVE_H_START(ha_start) |
> DSI_ACTIVE_H_END(ha_end));
> @@ -993,19 +1080,50 @@ static void dsi_timing_setup(struct
> msm_dsi_host *msm_host, bool is_dual_dsi)
> DSI_ACTIVE_VSYNC_VPOS_START(vs_start) |
> DSI_ACTIVE_VSYNC_VPOS_END(vs_end));
> } else { /* command mode */
> + if (msm_host->dsc) {
> + struct msm_display_dsc_config *dsc = msm_host->dsc;
> + u32 reg, reg_ctrl, reg_ctrl2;
> + u32 slice_per_intf, bytes_in_slice, total_bytes_per_intf;
> +
> + reg_ctrl = dsi_read(msm_host,
> REG_DSI_COMMAND_COMPRESSION_MODE_CTRL);
> + reg_ctrl2 = dsi_read(msm_host,
> REG_DSI_COMMAND_COMPRESSION_MODE_CTRL2);
> +
> + slice_per_intf = DIV_ROUND_UP(hdisplay, dsc->drm->slice_width);
> + bytes_in_slice = DIV_ROUND_UP(dsc->drm->slice_width *
> + dsc->drm->bits_per_pixel, 8);
> + dsc->drm->slice_chunk_size = bytes_in_slice;
> + total_bytes_per_intf = dsc->bytes_in_slice * slice_per_intf;
> + dsc->pkt_per_line = slice_per_intf / dsc->drm->slice_count;
> +
> + reg = 0x39 << 8;
> + reg |= ffs(dsc->pkt_per_line) << 6;
> +
> + dsc->eol_byte_num = total_bytes_per_intf % 3;
> + reg |= dsc->eol_byte_num << 4;
> + reg |= 1;
> +
> + reg_ctrl |= reg;
> + reg_ctrl2 |= bytes_in_slice;
> +
> + dsi_write(msm_host, REG_DSI_COMMAND_COMPRESSION_MODE_CTRL, reg);
> + dsi_write(msm_host, REG_DSI_COMMAND_COMPRESSION_MODE_CTRL2,
> reg_ctrl2);
> + }
> +
> /* image data and 1 byte write_memory_start cmd */
> - wc = hdisplay * dsi_get_bpp(msm_host->format) / 8 + 1;
> + if (!msm_host->dsc)
> + wc = hdisplay * dsi_get_bpp(msm_host->format) / 8 + 1;
> + else
> + wc = mode->hdisplay / 2 + 1;
>
> - dsi_write(msm_host, REG_DSI_CMD_MDP_STREAM0_CTRL,
> - DSI_CMD_MDP_STREAM0_CTRL_WORD_COUNT(wc) |
> - DSI_CMD_MDP_STREAM0_CTRL_VIRTUAL_CHANNEL(
> - msm_host->channel) |
> - DSI_CMD_MDP_STREAM0_CTRL_DATA_TYPE(
> - MIPI_DSI_DCS_LONG_WRITE));
> + data = DSI_CMD_MDP_STREAM0_CTRL_WORD_COUNT(wc) |
> + DSI_CMD_MDP_STREAM0_CTRL_VIRTUAL_CHANNEL(msm_host->channel) |
> + DSI_CMD_MDP_STREAM0_CTRL_DATA_TYPE(MIPI_DSI_DCS_LONG_WRITE);
>
> - dsi_write(msm_host, REG_DSI_CMD_MDP_STREAM0_TOTAL,
> - DSI_CMD_MDP_STREAM0_TOTAL_H_TOTAL(hdisplay) |
> - DSI_CMD_MDP_STREAM0_TOTAL_V_TOTAL(mode->vdisplay));
> + dsi_write(msm_host, REG_DSI_CMD_MDP_STREAM0_CTRL, data);
> +
> + data = DSI_CMD_MDP_STREAM0_TOTAL_H_TOTAL(hdisplay) |
> + DSI_CMD_MDP_STREAM0_TOTAL_V_TOTAL(mode->vdisplay);
> + dsi_write(msm_host, REG_DSI_CMD_MDP_STREAM0_TOTAL, data);
> }
> }
>
> @@ -2074,6 +2192,7 @@ int msm_dsi_host_modeset_init(struct
> mipi_dsi_host *host,
> struct msm_dsi_host *msm_host = to_msm_dsi_host(host);
> const struct msm_dsi_cfg_handler *cfg_hnd = msm_host->cfg_hnd;
> struct platform_device *pdev = msm_host->pdev;
> + struct msm_drm_private *priv;
> int ret;
>
> msm_host->irq = irq_of_parse_and_map(pdev->dev.of_node, 0);
> @@ -2093,6 +2212,9 @@ int msm_dsi_host_modeset_init(struct
> mipi_dsi_host *host,
> }
>
> msm_host->dev = dev;
> + priv = dev->dev_private;
> + priv->dsc = msm_host->dsc;
> +
> ret = cfg_hnd->ops->tx_buf_alloc(msm_host, SZ_4K);
> if (ret) {
> pr_err("%s: alloc tx gem obj failed, %d\n", __func__, ret);

\
 
 \ /
  Last update: 2021-08-03 03:17    [W:0.244 / U:0.460 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site