lkml.org 
[lkml]   [2021]   [Aug]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RFC][PATCH] usb: dwc3: usb: dwc3: Force stop EP0 transfers during pullup disable
From
Date
Hi Thinh,

On 8/19/2021 6:52 PM, Thinh Nguyen wrote:
> Wesley Cheng wrote:
>> Hi Thinh,
>>
>> On 8/18/2021 5:40 PM, Thinh Nguyen wrote:
>>> Wesley Cheng wrote:
>>>> Hi Thinh/Felipe,
>>>>
>>>> On 8/16/2021 12:13 PM, Wesley Cheng wrote:
>>>>> Hi Thinh,
>>>>>
>>>>> On 8/15/2021 5:33 PM, Thinh Nguyen wrote:
>>>>>> Felipe Balbi wrote:
>>>>>>>
>>>>>>> Hi,
>>>>>>>
>>>>>>> Thinh Nguyen <Thinh.Nguyen@synopsys.com> writes:
>>>>>>>>>>>>>>>> If this occurs, then the entire pullup disable routine is skipped and
>>>>>>>>>>>>>>>> proper cleanup and halting of the controller does not complete.
>>>>>>>>>>>>>>>> Instead of returning an error (which is ignored from the UDC
>>>>>>>>>>>>>>>> perspective), do what is mentioned in the comments and force the
>>>>>>>>>>>>>>>> transaction to complete and put the ep0state back to the SETUP phase.
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
>>>>>>>>>>>>>>>> ---
>>>>>>>>>>>>>>>> drivers/usb/dwc3/ep0.c | 4 ++--
>>>>>>>>>>>>>>>> drivers/usb/dwc3/gadget.c | 6 +++++-
>>>>>>>>>>>>>>>> drivers/usb/dwc3/gadget.h | 3 +++
>>>>>>>>>>>>>>>> 3 files changed, 10 insertions(+), 3 deletions(-)
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c
>>>>>>>>>>>>>>>> index 6587394..abfc42b 100644
>>>>>>>>>>>>>>>> --- a/drivers/usb/dwc3/ep0.c
>>>>>>>>>>>>>>>> +++ b/drivers/usb/dwc3/ep0.c
>>>>>>>>>>>>>>>> @@ -218,7 +218,7 @@ int dwc3_gadget_ep0_queue(struct usb_ep *ep, struct usb_request *request,
>>>>>>>>>>>>>>>> return ret;
>>>>>>>>>>>>>>>> }
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> -static void dwc3_ep0_stall_and_restart(struct dwc3 *dwc)
>>>>>>>>>>>>>>>> +void dwc3_ep0_stall_and_restart(struct dwc3 *dwc)
>>>>>>>>>>>>>>>> {
>>>>>>>>>>>>>>>> struct dwc3_ep *dep;
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> @@ -1073,7 +1073,7 @@ void dwc3_ep0_send_delayed_status(struct dwc3 *dwc)
>>>>>>>>>>>>>>>> __dwc3_ep0_do_control_status(dwc, dwc->eps[direction]);
>>>>>>>>>>>>>>>> }
>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>> -static void dwc3_ep0_end_control_data(struct dwc3 *dwc, struct dwc3_ep *dep)
>>>>>>>>>>>>>>>> +void dwc3_ep0_end_control_data(struct dwc3 *dwc, struct dwc3_ep *dep)
>>>>>>>>>>>>>>>> {
>>>>>>>>>>>>>>>> struct dwc3_gadget_ep_cmd_params params;
>>>>>>>>>>>>>>>> u32 cmd;
>>>>>>>>>>>>>>>> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
>>>>>>>>>>>>>>>> index 54c5a08..a0e2e4d 100644
>>>>>>>>>>>>>>>> --- a/drivers/usb/dwc3/gadget.c
>>>>>>>>>>>>>>>> +++ b/drivers/usb/dwc3/gadget.c
>>>>>>>>>>>>>>>> @@ -2437,7 +2437,11 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
>>>>>>>>>>>>>>>> msecs_to_jiffies(DWC3_PULL_UP_TIMEOUT));
>>>>>>>>>>>>>>>> if (ret == 0) {
>>>>>>>>>>>>>>>> dev_err(dwc->dev, "timed out waiting for SETUP phase\n");
>>>>>>>>>>>>>>>> - return -ETIMEDOUT;
>>>>>>>>>>>>>>>> + spin_lock_irqsave(&dwc->lock, flags);
>>>>>>>>>>>>>>>> + dwc3_ep0_end_control_data(dwc, dwc->eps[0]);
>>>>>>>>>>>>>>>> + dwc3_ep0_end_control_data(dwc, dwc->eps[1]);
>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>> End transfer command takes time, need to wait for it to complete before
>>>>>>>>>>>>>>> issuing Start transfer again. Also, why restart again when it's about to
>>>>>>>>>>>>>>> be disconnected.
>>>>>>>>>>>>>>
>>>>>>>>>>>>>> I can try without restarting it again, and see if that works. Instead
>>>>>>>>>>>>>> of waiting for the command complete event, can we set the ForceRM bit,
>>>>>>>>>>>>>> similar to what we do for dwc3_remove_requests()?
>>>>>>>>>>>>>>
>>>>>>>>>>>>>
>>>>>>>>>>>>> ForceRM=1 means that the controller will ignore updating the TRBs
>>>>>>>>>>>>> (including not clearing the HWO and remain transfer size). The driver
>>>>>>>>>>>>> still needs to wait for the command to complete before issuing Start
>>>>>>>>>>>>> Transfer command. Otherwise Start Transfer won't go through. If we know
>>>>>>>>>>>>> that we're not going to issue Start Transfer any time soon, then we may
>>>>>>>>>>>>> be able to get away with ignoring End Transfer command completion.
>>>>>>>>>>>>>
>>>>>>>>>>>>
>>>>>>>>>>>> I see. Currently, in the place that we do use
>>>>>>>>>>>> dwc3_ep0_end_control_data(), its followed by
>>>>>>>>>>>> dwc3_ep0_stall_and_restart() which would execute start transfer. For
>>>>>>>>>>>
>>>>>>>>>>> That doesn't look right. You can try to see if it can recover from a
>>>>>>>>>>> control write request. Often time we do control read and not write.
>>>>>>>>>>> (i.e. try to End Transfer and immediately Start Transfer on the same
>>>>>>>>>>> direction control endpoint).
>>>>>>>>>>>
>>>>>>>>>> OK, I can try, but just to clarify, I was referring to how it was being
>>>>>>>>>> done in:
>>>>>>>>>>
>>>>>>>>>> static void dwc3_ep0_xfernotready(struct dwc3 *dwc,
>>>>>>>>>> const struct dwc3_event_depevt *event)
>>>>>>>>>> {
>>>>>>>>>> ...
>>>>>>>>>> if (dwc->ep0_expect_in != event->endpoint_number) {
>>>>>>>>>> struct dwc3_ep *dep = dwc->eps[dwc->ep0_expect_in];
>>>>>>>>>>
>>>>>>>>>> dev_err(dwc->dev, "unexpected direction for Data Phase\n");
>>>>>>>>>> dwc3_ep0_end_control_data(dwc, dep);
>>>>>>>>>> dwc3_ep0_stall_and_restart(dwc);
>>>>>>>>>> return;
>>>>>>>>>> }
>>>>>>>>>>
>>>>>>>>
>>>>>>>> Looking at this snippet again, it looks wrong. For control write
>>>>>>>> unexpected direction, if the driver hasn't setup and started the DATA
>>>>>>>> phase yet, then it's fine, but there is a problem if it did.
>>>>>>>>
>>>>>>>> Since dwc3_ep0_end_control_data() doesn't issue End Transfer command to
>>>>>>>> ep0 due to the resource_index check, it doesn't follow the control
>>>>>>>
>>>>>>> IIRC resource_index is always non-zero, so the command should be
>>>>>>
>>>>>> No, resource_index for ep0out is 0, ep0in is 1. You can check from any
>>>>>> of the driver tracepoint log for the return value of Start Transfer
>>>>>> command for the resource index of ep0. There could be a mixed up with
>>>>>> the undocumented return value of Set Endpoint Transfer Resource command
>>>>>> before when this code was written, don't mix up with that.
>>>>>>
>>>>>>> triggered. If you have access to a Lecroy USB Trainer, could you script
>>>>>>> this very scenario for verification?
>>>>>>
>>>>>> For anyone who wants to work on this, we don't need a LeCroy USB
>>>>>> trainer. If you use xhci host, just modify the xhci-ring.c to queue a
>>>>>> wrong direction DATA phase TRB of a particular control write request
>>>>>> test, and continue with the next control requests.
>>>>>>
>>>>> Let me give this a try since I already have a modified (broken :)) XHCI
>>>>> stack.
>>>>>
>>>>> Thanks
>>>>> Wesley Cheng
>>>>
>>>> Sorry for the late response. I was trying to get a reliable change to
>>>> get the issue to reproduce. I think I was able to find a set up which
>>>> will generate the unexpected direction issue. I'll try my best to
>>>> summarize the traces here:
>>>>
>>>> Set up:
>>>> - Modified XHCI stack to queue an IN TRB for a three stage CONTROL OUT
>>>> transaction (OUT data stage)
>>>> - Device is using RNDIS, as that has interface specific commands (ie
>>>> SEND_ENCAPSUALTED messages)
>>>>
>>>> Kernel Log:
>>>> [ 1255.312870] msm-usb-hsphy 88e3000.hsphy: Avail curr from USB = 900
>>>> [ 1255.315300] dwc3_ep0_xfernotready event status = 1
>>>> [ 1255.315429] dwc3_ep0_xfernotready event status = 2
>>>> [ 1255.316390] android_work: sent uevent USB_STATE=CONFIGURED
>>>> [ 1255.317467] dwc3_ep0_xfernotready event status = 1
>>>> [ 1255.317588] dwc3_ep0_xfernotready event status = 2
>>>> [ 1255.334196] dwc3_ep0_xfernotready event status = 1
>>>> [ 1255.334217] dwc3 a600000.dwc3: unexpected direction for Data Phase
>>>> [ 1255.334311] rndis_msg_parser: unknown RNDIS message 0x0052033A len
>>>> 4456526
>>>> [ 1255.334328] RNDIS command error -524, 0/24
>>>> [ 1255.334369] ------------[ cut here ]------------
>>>> [ 1255.334377] dwc3 a600000.dwc3: No resource for ep0out
>>>> [ 1255.334440] WARNING: CPU: 0 PID: 8364 at
>>>> drivers/usb/dwc3/gadget.c:360 dwc3_send_gadget_ep_cmd+0x3c4/0x96c
>>>> ...
>>>> 1255.336163] WARNING: CPU: 0 PID: 8364 at drivers/usb/dwc3/ep0.c:281
>>>> dwc3_ep0_out_start+0x108/0x144
>>>>
>>>> So the kernel log does indeed show the concern mentioned by Thinh, where
>>>> after ending the transfer, we do see the dwc3_ep0_out_start() fail due
>>>> to no xfer resource.
>>>>
>>>
>>> No, there's no end transfer command seen, and it's expected from code
>>> review.
>>>
>> Sorry, yes that's correct.
>>>> ftrace:
>>>> <...>-8364 [000] d..1 1255.333988: dwc3_ctrl_req: Get Interface
>>>> Status(Intf = 0, Length = 24)
>>>> <...>-8364 [000] d..1 1255.334115: dwc3_prepare_trb: ep0out: trb
>>>> ffffffc01bffd000 (E1:D0) buf 00000000efb76000 size 24 ctrl 00000455
>>>> (HlCs:Sc:data)
>>>> <...>-8364 [000] d..1 1255.334128: dwc3_prepare_trb: ep0out: trb
>>>> ffffffc01bffd010 (E1:D0) buf 00000000efff9000 size 488 ctrl 00000c53
>>>> (HLcs:SC:data)
>>>> <...>-8364 [000] d..1 1255.334166: dwc3_gadget_ep_cmd: ep0out: cmd
>>>> 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status:
>>>> Successful
>>>> <...>-8364 [000] d..1 1255.334239: dwc3_gadget_ep_cmd: ep0out: cmd
>>>> 'Set Stall' [404] params 00000000 00000000 00000000 --> status: Successful
>>>> <...>-8364 [000] d..1 1255.334291: dwc3_gadget_giveback: ep0out: req
>>>> ffffff8891724e00 length 0/24 zsI ==> -104
>>>
>>> It detected wrong direction and sets STALL here, but no End Transfer
>>> command.
>>>
>>>> <...>-8364 [000] d..1 1255.334339: dwc3_prepare_trb: ep0out: trb
>>>> ffffffc01bffd010 (E1:D0) buf 00000000efffa000 size 8 ctrl 00000c23
>>>> (HLcs:SC:setup)
>>>
>>> The driver overwrote the active TRB with a new SETUP TRB.
>>>
>>>> <...>-8364 [000] d..1 1255.336099: dwc3_gadget_ep_cmd: ep0out: cmd
>>>> 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: No
>>>> Resource
>>>
>>> The dep->flags DWC3_EP_TRANSFER_STARTED got cleared. When it tries to
>>> issue a Start Transfer a SETUP transfer, the command will fail with no
>>> resource because the endpoint never ended properly.
>>>
>>>> <...>-8364 [000] d..1 1255.357594: dwc3_ctrl_req: 00 60 b7 ef 00 00
>>>> 00 00
>>>
>>> Here is iffy because the behavior is undefined. The driver overwrote the
>>> previous TRB. The Start Transfer command didn't go through, so the
>>> controller still has the old TRB setup in its cache. It gets the next
>>> SETUP request completion anyway because the SETUP stage is a short
>>> packet. The driver updated its state that it's expecting the SETUP
>>> stage, and it doesn't check the TRB write back buffer size for more or
>>> less than 8 bytes or whether this is valid data.
>>>
>>> Wesley, is this SETUP packet the correct RNDIS control request?
>>>
>> That doesn't look to be a RNDIS control packet. I collected a bus
>> analyzer log as well w/ this snippet, and nothing was transmitted from
>> the host side during the data stage. Subsequent SETUP transactions were
>> standard USB descriptors (GET string descriptors).
>
> Ok.
>
>>>> <...>-8364 [000] d..1 1255.357680: dwc3_gadget_ep_cmd: ep0out: cmd
>>>> 'Set Stall' [404] params 00000000 00000000 00000000 --> status: Successful
>>>
>>> The device Set Stall on an unrecognized request, probably from the
>>> application, which can be normal.
>>>
>>>> <...>-8364 [000] d..1 1255.357696: dwc3_prepare_trb: ep0out: trb
>>>> ffffffc01bffd010 (E1:D0) buf 00000000efffa000 size 8 ctrl 00000c23
>>>> (HLcs:SC:setup)
>>>> <...>-8364 [000] d..1 1255.357722: dwc3_gadget_ep_cmd: ep0out: cmd
>>>> 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status:
>>>> Successful
>>>> <...>-224 [005] d..1 1266.313014: dwc3_gadget_ep_cmd: ep2out: cmd
>>>> 'End Transfer' [40c08] params 00000000 00000000 00000000 --> status:
>>>> Timed Out
>>>>
>>>> Thanks
>>>> Wesley Cheng
>>>>
>>>
>>> Thanks for the test Wesley
>>>
>>> BR,
>>> Thinh
>>>
>>
>> So back to the original issue, which was the SETUP timeout during pullup
>> disable, I went ahead and collected the ftrace w/ a change to just
>> remove the return statement:
>>
>> ret = wait_for_completion_timeout(&dwc->ep0_in_setup,
>> msecs_to_jiffies(DWC3_PULL_UP_TIMEOUT));
>> if (ret == 0) {
>> dev_err(dwc->dev, "timed out waiting for SETUP phase\n");
>> return -ETIMEDOUT;
>> }
>>
>> This would allow the __dwc3_gadget_stop() to disable EP0/1, which would
>> call dwc3_gadget_stop_active_transfer() to send the end xfer command:
>>
>> //Packet which will not queue a data stage (injected failure)
>> <...>-7098 [003] d..1 346.560711: dwc3_ctrl_req: Get String
>> Descriptor(Index = 3, Length = 2)
>>
>> //Prepare IN data stage TRB
>> <...>-7098 [003] d..1 346.560865: dwc3_prepare_trb: ep0in: trb
>> ffffffc011edd000 (E0:D0) buf 00000000effcc000 size 2 ctrl 00000c53
>> (HLcs:SC:data)
>> <...>-7098 [003] d..1 346.560915: dwc3_gadget_ep_cmd: ep0in: cmd
>> 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status:
>> Successful
>>
>> //Pullup disable here kicks in - __dwc3_gadget_stop()
>> <...>-224 [006] d..1 348.607367: dwc3_gadget_ep_disable: ep0out:
>> mps 64/512 streams 0 burst 1 ring 0/0 flags E:swbp:>
>> <...>-224 [006] d..1 348.607430: dwc3_gadget_giveback: ep0out: req
>> ffffff884e5f5500 length 0/2 zsI ==> -108
>> <...>-224 [006] d..1 348.607444: dwc3_gadget_ep_disable: ep0in:
>> mps 64/512 streams 0 burst 1 ring 0/0 flags E:swBp:<
>>
>> //End transfer on the pending EP0 in TRB queued previously
>> <...>-224 [006] d..1 348.607484: dwc3_gadget_ep_cmd: ep0in: cmd
>> 'End Transfer' [10c08] params 00000000 00000000 00000000 --> status:
>> Successful
>> <...>-224 [006] dN.1 348.607788: usb_gadget_vbus_draw: speed 3/6
>> state 6 0mA [sg:self-powered:activated:disconnected] --> 0
>> <...>-224 [006] .... 348.616888: usb_gadget_disconnect: speed 3/6
>> state 6 0mA [sg:self-powered:activated:disconnected] --> 0
>>
>> Does this look ok, Thinh?
>>
>
> It should be fine.
>
> The way we're handling soft-connect and soft-disconnect in dwc3 is
> different than what the programming guide suggested. We're not doing
> soft-reset on soft-connect. Our HW testing didn't show a problem in
> quick soft-connect/disconnect succession before, but can you test doing
> soft-connect immediately after this scenario?
>

Thanks Thinh.

I can try. Currently, the Android USB framework will immediately rebind
to the UDC if I run the below command from the console:
echo "" > /config/usb_gadget/g1/UDC

So that will be a quick pullup disable (due to the command) and then a
subsequent pullup enable from the Android USB framework. I'll run a
script overnight to keep doing the echo command above.
> Also, maybe we can change dev_err() print to dev_warn() on timeout instead?
>
Sure, will do.

Thanks
Wesley Cheng
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

\
 
 \ /
  Last update: 2021-08-20 05:06    [W:0.076 / U:0.400 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site